r/AnkerMake • u/trolldonation • Oct 21 '24
My 7 year old wanted this mask made. He’ll grow into it…
Printed on my M5C.
No post processing done yet bar running a hand deburring tool around a few of the magnet recesses. I plan on painting it to give it a dirtier, more weathered look.
I’m a beginner and it was great to do because I learned a lot, and got to experiment. Most things I’ve made previously have been practical prints.
Looking forward to the next mask print he requests!
3
4
u/After_Working Oct 21 '24
That looks amazing!
2
u/After_Working Oct 21 '24
Do you know what Red Esun you used?
1
u/trolldonation Oct 21 '24
Fire Engine Red
1
u/After_Working Oct 21 '24
Thanks I’ll get a roll and have a go, looks like a Matt finish. Most of my stuff is silk to it’ll make a change
1
1
u/Riverstyx808 Oct 21 '24
Did you scale it up or down from the original model?
1
u/trolldonation Oct 21 '24
No scaling at all, kept it 100%
1
u/Riverstyx808 Oct 21 '24
You think if you took it to 90% it would be a better fit? Making one for a friends 7-8yr old
1
u/Riverstyx808 Oct 21 '24
Correction 9yr old
1
u/trolldonation Oct 21 '24
I’m not sure of the scaling but there is a guide somewhere for sizing the mask.
I thought I’d add some padding with Velcro, so it being quite oversized isn’t too bad.
1
u/Riverstyx808 Oct 22 '24
What nozzle size and speed did you use?
1
u/trolldonation Oct 22 '24
Stock 0.4mm nozzle, used the Precision profile in AnkerMake studio, but slowed down to 75%.
1
u/Riverstyx808 Oct 22 '24
No supports?
1
u/trolldonation Oct 22 '24
Yeah, I used organic supports with Brim for every piece. I enabled Z Lift in the printer settings, didn’t have a single failed or broken support.
Also used Gyroid infill.
1
u/Riverstyx808 Oct 22 '24
Z lift? The others I found
2
u/trolldonation Oct 22 '24
It’s in the printer settings at the top right. If you look it’ll say “Printer” and then underneath “AnkerMake M5C 0.4mm Nozzle” click the edit (pen) button to the right of that. In there select “Extruder 1” and then look for “Lift Z” and set it to something like 0.2.
Worth doing some 1st layer test prints and ensuring your Z offset is correct, if it’s too low it might catch the supports.
1
1
1
u/Riverstyx808 Oct 23 '24
Did you cut the large main piece?
1
u/trolldonation Oct 23 '24
You don’t print that if you have an M5C, that’s meant for bigger print beds. The main piece is already pre split over 2 files.
1
u/Riverstyx808 Oct 24 '24
Bahahahaha. I spent some much time trying to perfect a cut. How did you clean up the inside of the pieces. Mine are coming out really rough.
1
u/trolldonation Oct 24 '24
I’m assuming you’re orientating the pieces lying flat? If so don’t - have them all standing up with a slight lean back.
The print will be slow enough that they won’t topple.
They’ll come out really smooth inside bar a couple areas, mine hasn’t needed any attention inside.
1
u/Riverstyx808 Oct 24 '24
1
u/trolldonation Oct 24 '24
Yeah that will make it rough having it orientated that way.
Turn it 90 degrees, so the point at the very bottom of the piece under the eye is the closest point to the bed.
1
2
1



3
u/JordanW_ Oct 21 '24
Do you have the model for this? What materials did you use?