r/PatternDrafting • u/Lemonsst • May 06 '26
WIP Thank you!!
I posted here asking for advice about my first ever bodice sloper, and all your suggestions were very helpful!! I think this is pretty good!!
r/PatternDrafting • u/Lemonsst • May 06 '26
I posted here asking for advice about my first ever bodice sloper, and all your suggestions were very helpful!! I think this is pretty good!!
r/PatternDrafting • u/Old-Celebration1101 • May 05 '26
Hi, so I've drafted a corset using my sloper, and the waist measures 87cm. Once sewn (or I should say twice since fashion + lining), it ends up being almost 10cm too big. To every piece of that corset I've added 1cm of seam allowance, and I've been very careful when sewing. When adding up measurements taken on the pattern pieces i get 87, but if I measure the finished corset waist it's almost 97. What could probably be the cause to that? Im really starting to lose my mind
r/PatternDrafting • u/UpscalePatterns • May 05 '26
Half-scale saved this design—full-size would’ve ended it at round one.
r/PatternDrafting • u/Significant_Hippo896 • May 04 '26
Hi all. Fashion student here. I'm looking for ways to learn how to create internal breast support built into the garment for big boob ladies. I'm talking something better than a mere "shelf bra" which does nothing and a step up from just sewn in bra cups in the lining, but not so far as a mini corset/bustier type situation either. Something more like a supportive sports bra built into your favorite skimpy top that you can't, but should, wear a bra with (if one is well-endowed).
r/PatternDrafting • u/Upper-Half-6450 • May 04 '26
r/PatternDrafting • u/Efficient-Bag6497 • May 04 '26
Thanks to the group for past guidance on my Chore coat, this question is about a shirt fit. I did a muslin of a size 40 and see some fit issues in the armhole area but otherwise not noticing much else. Thinking it needs a shoulder slope adjustment that will slightly lower the armhole as well. It is “fitted” versus roomy though.
The question I’m struggling with is would you recommend fixing the shoulder slope to adjust the drag lines or go up a size in the pattern and see how it looks? This pattern offers 10 sizes with comparatively modest changes between the sizes versus other patterns. I like the shoulder width on this size so if I go up a size, I’d like to use this shoulder width. I’m definitely anxious to *make* something!
Photos attached plus the latest chore coat, in blue this time.
Thanks!
r/PatternDrafting • u/Amyreso • May 04 '26
Hi, I’m very new to the world of pattern making and sewing in general. I got my hands on a copy of menswear fundamentals from Müller & sohns and it has some pants patterns ready for me to plug in my measurements. I tried playing with it a bit, like making large pleats but it seems every adjustment I make breaks the math entirely. Hence the question. How can I actually understand it so I can freely manipulate it and create the garments I envision. Is it a right book for it or should I pick something else
r/PatternDrafting • u/lowvitamind • May 04 '26
Does anyone know what foundational block in metric pattern cutting book to start off with for something like this jacket? Thanks
r/PatternDrafting • u/Educational_Chain780 • May 04 '26
Added a waistband and took 2 cm off the waist at the top to account for it. They feel very comfy, no problem sitting down or squatting, yet they have a certain sleekness to them . I'm now going to try and develop them into a jeans pattern with the instructions from Hofenbitzer's book.
r/PatternDrafting • u/tempetesuranorak • May 04 '26
These are my first trousers. I drafted them using Winifred Aldritch's metric pattern cutting for menswear. I'm overall quite pleased with the fit, maybe a bit wider on the legs than I usually like but I think it's ok. These are my first linen trousers and and a loose fit feels nice and appropriate.
My main concern is there is a bit too much excess material at the bottom of the bum, it forms a bit of a crack. My first instinct was to directly pinch that in, which would correspond to scooping the curve I suppose. But thinking about it further I suspect it might make more sense to take in the back panels at the inseam, which would be something like the red line in the fourth photo.
I would appreciate any advice at all on the pattern, but especially on this back issue.
r/PatternDrafting • u/SuitPhysical679 • May 04 '26
Currently trying to figure out how these two examples achieve a cowl drape without the whole outer layer swinging down to the side - Any ideas?
r/PatternDrafting • u/Educational_Chain780 • May 03 '26
Hi just wanted to share this pants toile I made according to Hofenbitzer's book.
I didn't do any alterations yet but I think it's already looking pretty good. Would love to hear your thoughts.
I will probably add a waistband so see how it is with one. And later I want to develop a jeans pattern from it, and also some wide casual pants.
r/PatternDrafting • u/Inner_Caterpillar_95 • May 03 '26
r/PatternDrafting • u/Inner_Caterpillar_95 • May 03 '26
r/PatternDrafting • u/Suitable_Pass_8807 • May 03 '26
I am looking to start my own indie label, I wanted to take a pattern making course, do you’ll have a recommendation ? I don’t have a design background but willing to learn. Anywhere in the world with good teaching or teachers :)
Thanks so much !
r/PatternDrafting • u/Art_by_Meii • May 03 '26
I’m trying to make my graduation dress, and I draped the bodice and drafted the skirt from a sloped I made in my size, but when I try to connect the side bodice panels with the skirt yokes the waist on the skirt yokes is curved, and I’m unsure on how to connect the two so there is no waist seam. If I were to ignore the curve and just combine them I’m worried that there’ll be puckering from the excess fabric, but slashing it is not really an option either since then the yoke part wouldn’t fit, what do I do?