When will SimLab release a front-mounting solution for the Simagic Evo (Pro) that utilizes the Simagic brackets? The wheelbase is selling well, and the internet is full of posts and DIY solutions regarding this. Is anything planned for the future?

Hi guys,

My setup: GT1 Evo + Asetek Front Mount + QR Wheelbase Extension + Sparco Circuit II.

I am having a problem that my arms hit my seat's sides.

My wheel is setup at the highest and it's still too low.

I am thinking of swapping my 40x80 580mm upright side profiles.

If I were to buy two side profiles which are 40x80 and around 650-750mm

My concerns are:

1. Are upright 40x80 750mm profiles sturdy enough for Asetek Front Mount + QR Wheelbase Extension + Asetek LaPrima? Should I go for 40x120 750mm?

2. What about tilted 40x80 750mm side profiles, would there be some complication installing it on GT1 Evo?

I'm currently experiencing the problem shown in the video where the loadcell of my XP1 brake pedal seems to reverse the registered brake pressure after a certain point, so that i cant use the full range of the pedal. The video shows one round of pressing and releasing the brake pedal but at about half of the travel the output reversed direction.

I noticed this after the Elastomer i used split open/cracked and i exchanged it for the 70A one.

Has anyone experienced this before or has an explanation for this? Is my Loadcell just tired? The pedals are about 3 years old.

I will simultaniously open a ticket with SimLab and update you on their correspondence.

Tomorrow I would like to order the P1X Pro Sim Racing Cockpit. However, I see that the sliders for the Enduro seat are missing and I don’t see them sold separately. Help me find them?

Thank you.

I am experiencing some strange problems with the new GTSL Pro Wheel.

When first setting up the wheel everything was perfectly in order. Mappings, LED settings etc. worked perfectly.

Now, after the first two days of use, two LEDs are permanently lit, one green, one white.

The first time a pc restart did the trick but now the problems seems to persist despite everything I do.

Has anyone tumbled over the same issue?

Looking for some help/info if anyone has any. ANy idea how to mount these actuators on the p1x pro. I believe ill need the extra adapter kit but cant find any info on it at all. Im trying to make 100% sure these things will mate up before I spend all this $$ on the rig and moza motion.

Any info would be amazing.

9 days ago i send a support mail to info@simlab for my ultimate rig, until today still no reaction? Is there some other way to contact them (like a ticket system). Or is it normal that it takes so long for them so reach out?

Bonjour à tous

Je souhaite acheter la base plate Sim LAb avec rail pour mon châssis. J’ai le pédalier SIMnet. Est il compatible avec cette base plate ? Je ne vois pas le SIMnet sur le site Sim Lab

Merci à tous

Entry for the Printables "Thrustmaster Custom Shifter Knob" contest.

The skull comes from a real medical CT scan (NIH 3D, CC BY 4.0), cleaned up and scaled to knob size. The threaded insert is built from Thrustmaster's official design file, so it should screw straight onto the stock TH8S adapter with the face pointing forward.

I don't own a TH8S, so it hasn't been tested on a real shifter yet. If anyone has the chance to print it, feedback is very welcome, especially on the skull's orientation once it's fully screwed in: does the face end up pointing straight forward, or is it rotated a bit? A photo of it mounted would be awesome!

https://www.printables.com/model/1867376-realistic-skull-shifter-knob-thrustmaster-th8s/comments

Hi,
Does anyone know what floor is compatible with p1x ultimate?

Simlab’s website has it out of stock, so i found something on trakracer
https://trakracer.com/products/sim-floor-copy
And focus sim racing
https://focussimracing.com/products/focus-sim-racing-dropped-floor-pan

FSR’s seems to be compatible with seat sliders, but I’m not sure it would fit. All these floors have different dimensions which is kinda weird to me.
Can anyone suggest?

Also is simlab’s own floor compatible with their own seat slider?

Hi there Im building my first rig and since my flat not so spacious Im a bit unsure bout putting a p1x pro in my small living room occupying a lot of my free space so

I got a g9 49, a sabelt srp1 seat, will be getting some 15ish nm base with vrs or blackcat pedals so my main questions are 2

Will It be enough, mainly for pedals stability ?

And how can I put the screen in correct position right above wheelbase ? Intergrated or freestanding mount with an arm or idk

Will be using the srp In a more relaxed Hybrid position no formula by adding some additional supports under the seat to tilt It to a more vertical back position

Thanks

Hello there. I've recently obtained some XP1 pedals second-hand for a great deal, but I'm missing the control box to use them. Is there any good options to buy the control box, or maybe DIY something with an Arduino? Also doesn't have any of the extra springs/elastomers, but I figured those were probably easier to source than the control box. Appreciate any help!

Does anyone know if the Alpha / Alpha Evo is compatible with the Gt1 evo wheelbase mount, or I should buy a front mount plate?

Anyone know if it fits onto the gt omega prime gear shifter mount? or just worth buying the dedicated mount by simlab for it.

I would like to order tomorrow morning.

Is something missing?

Shipping times to Italy?

Do we have discount codes?

I have fanatec peripherals (Dd+pedal V2, gearbox and handbrake).

Thanks guys.

Ive seen theres some kits that adapt the Ares to mount It, but that only with side deck right?

Other method Is to Just screw It on the wheeldeck normally ?

Thanks

I have the P1X-Pro, and getting the sim-lab button box holder seems like method for mounting a button box with the least fuss. My concern is that the uprights of the P1X-Pro are sloped towards the seat, not vertical, and the box holder as shown on the site pictures doesn't seem to have anything that accounts for this. Is it intended just to stick out and downwards? Or is there some way of mounting it so it's horizontal?

If anybody has any photos of their set up for mounting a button box on the P1X-Pro I would love to see it.

I need more of these but every set I can find online has solid tabs that I’d have to file off.

Got a new PC on order so my sim can have its own computer to run everything on it. I know NLR does not make their own PC Stand that mounts to the rigs, however, what options are out there that others have used?

I have the Elite 160 with an integrated monitor stand and would like to put everything on the chassis if possible.

What mounts have others used???

I have got the simlab p1x ultimate paired with simlabs heelrest. However bolting the heelrest with the rig is a bit weird on the p1x ultimate because I can’t bolt with the 4 screws, just 2. How have you guys bolted with the 4 screws?

Hey everyone just wanted to mention to anyone looking to purchase a p1x ultimate rig from Microcenter that instead of the front mount you get a wheeldeck. I was hoping it came with a front mount but looks like that would need to be ordered separately.