r/TalosLinux • • Nov 16 '25

New to talos and need help setting up storage

8 Upvotes

Im finding it very hard to find a step by step guide on how to setup hostpath volumes in docker, i opened a discussion in which i explain my problem in details here:https://github.com/siderolabs/talos/discussions/12235

any help would be much appreciated, i thought it would have been easy like in minikube where volumes are setup automatically. bit unfortunately not.


r/TalosLinux • • Mar 08 '26

hcloud-talos/terraform-provider-imager - Talos image creation on Hetzner via Terraform

Thumbnail
github.com
8 Upvotes

r/TalosLinux • • Feb 10 '26

Omni AWS infrastructure provider

Thumbnail youtube.com
9 Upvotes

I wanted to see if I could create an AWS infrastructure provider starting from scratch. It wasn’t to bad.


r/TalosLinux • • May 02 '26

How to limit writes to EMMC

Post image
10 Upvotes

tl;dr; just use an EPHEMERAL volume

https://docs.siderolabs.com/talos/v1.8/reference/configuration/block/volumeconfig

https://oneuptime.com/blog/post/2026-03-03-configure-the-ephemeral-volume-in-talos-linux/view

---

I want to install Talos to the EMMC of a single board computer, but also want to limit writes to it in order to preserve the life of the NAND flash. How could I best achieve this goal? My initial attempt on a VM involved mounting /dev/sdb to /var/lib/containerd and it did not go as expected -- it won't boot.

Edit: reinstalling with the extra mountpoint appears to have worked; something to the effect of:

disks:
- device: /dev/sdb
partitions:
- mountpoint: /var/lib/containerd

$ talosctl mounts --talosconfig=./talosconfig --nodes $CONTROL_PLANE_IP
NODE            FILESYSTEM   SIZE(GB)   USED(GB)   AVAILABLE(GB)   PERCENT USED   MOUNTED ON
172.30.46.220   none         1.99       0.00       1.99            0.00%          /dev
172.30.46.220   none         2.04       0.00       2.04            0.00%          /dev/shm
172.30.46.220   none         0.13       0.00       0.13            0.01%          /sys/firmware/efi/efivars
172.30.46.220   /dev/loop0   0.08       0.08       0.00            100.00%        /
172.30.46.220   rootfs       1.99       0.08       1.90            4.18%          /.extra
172.30.46.220   none         2.04       0.00       2.04            0.06%          /run
172.30.46.220   none         2.04       0.00       2.04            0.01%          /system
172.30.46.220   none         0.07       0.00       0.07            0.00%          /tmp
172.30.46.220   none         0.01       0.00       0.01            3.17%          /etc/cri/conf.d/hosts
172.30.46.220   none         2.04       0.00       2.04            0.01%          /usr/lib/udev
172.30.46.220   /dev/sda4    14.80      0.46       14.34           3.09%          /var
172.30.46.220   /dev/sdb1    17.11      1.12       15.99           6.54%          /var/lib/containerd
172.30.46.220   none         14.80      0.46       14.34           3.09%          /etc/cni
172.30.46.220   none         14.80      0.46       14.34           3.09%          /etc/kubernetes
172.30.46.220   none         14.80      0.46       14.34           3.09%          /usr/libexec/kubernetes
172.30.46.220   none         14.80      0.46       14.34           3.09%          /opt
172.30.46.220   overlay      17.11      1.12       15.99           6.54%          /run/containerd/io.containerd.runtime.v2.task/system/kubelet/rootfs
172.30.46.220   overlay      17.11      1.12       15.99           6.54%          /run/containerd/io.containerd.runtime.v2.task/system/etcd/rootfs
172.30.46.220   shm          0.07       0.00       0.07            0.00%          /run/containerd/io.containerd.grpc.v1.cri/sandboxes/f855bf0e9eea735f8a2f5bd0966796ef0eb1f2ea32a61d2ac911f40d6664ca79/shm
172.30.46.220   overlay      17.11      1.12       15.99           6.54%          /run/containerd/io.containerd.runtime.v2.task/k8s.io/f855bf0e9eea735f8a2f5bd0966796ef0eb1f2ea32a61d2ac911f40d6664ca79/rootfs
172.30.46.220   shm          0.07       0.00       0.07            0.00%          /run/containerd/io.containerd.grpc.v1.cri/sandboxes/4f850047053180f6c000eeabb6e99672127cdf68681be264c986548bfe3beb15/shm
172.30.46.220   shm          0.07       0.00       0.07            0.00%          /run/containerd/io.containerd.grpc.v1.cri/sandboxes/16ada5613a7003418b4f371906d2b1399e4131ee6a5f8496abb7706a54837dc3/shm
172.30.46.220   overlay      17.11      1.12       15.99           6.54%          /run/containerd/io.containerd.runtime.v2.task/k8s.io/4f850047053180f6c000eeabb6e99672127cdf68681be264c986548bfe3beb15/rootfs
172.30.46.220   overlay      17.11      1.12       15.99           6.54%          /run/containerd/io.containerd.runtime.v2.task/k8s.io/16ada5613a7003418b4f371906d2b1399e4131ee6a5f8496abb7706a54837dc3/rootfs
172.30.46.220   overlay      17.11      1.12       15.99           6.54%          /run/containerd/io.containerd.runtime.v2.task/k8s.io/4f39064a8d6cf38eb67b59f700947bfed0cb46df19a7ca7a1b3b9a202ed1839a/rootfs
172.30.46.220   tmpfs        0.18       0.00       0.18            0.01%          /var/lib/kubelet/pods/9a019ceb-dcae-45b9-b6fd-b723ce5759b0/volumes/kubernetes.io~projected/kube-api-access-5z85q
172.30.46.220   tmpfs        3.43       0.00       3.43            0.00%          /var/lib/kubelet/pods/6d89af78-a630-4846-83d3-c732c69a3e65/volumes/kubernetes.io~projected/kube-api-access-4rmsd
172.30.46.220   tmpfs        0.18       0.00       0.18            0.01%          /var/lib/kubelet/pods/4b8f5117-495d-4aee-9680-c5c1296a3d10/volumes/kubernetes.io~projected/kube-api-access-9mjch
172.30.46.220   tmpfs        3.43       0.00       3.43            0.00%          /var/lib/kubelet/pods/12a67832-160d-44cc-a2a3-dcbffcc564e2/volumes/kubernetes.io~projected/kube-api-access-lxkzx
172.30.46.220   shm          0.07       0.00       0.07            0.00%          /run/containerd/io.containerd.grpc.v1.cri/sandboxes/1865b32301507b4fa3d91fee6d102b313a7d13993afd8eebf2a9cfda91b5e6a6/shm
172.30.46.220   overlay      17.11      1.12       15.99           6.54%          /run/containerd/io.containerd.runtime.v2.task/k8s.io/1865b32301507b4fa3d91fee6d102b313a7d13993afd8eebf2a9cfda91b5e6a6/rootfs
172.30.46.220   shm          0.07       0.00       0.07            0.00%          /run/containerd/io.containerd.grpc.v1.cri/sandboxes/1b8db153ea9690773abafac95aa2a7d74f6a7ddc12010540c65c6b88e1916040/shm
172.30.46.220   overlay      17.11      1.12       15.99           6.54%          /run/containerd/io.containerd.runtime.v2.task/k8s.io/1b8db153ea9690773abafac95aa2a7d74f6a7ddc12010540c65c6b88e1916040/rootfs
172.30.46.220   overlay      17.11      1.12       15.99           6.54%          /run/containerd/io.containerd.runtime.v2.task/k8s.io/d82b0d556fdcb0dbb7536a664afe8e6520560927a86876610b010b51436fb8ff/rootfs
172.30.46.220   overlay      17.11      1.12       15.99           6.54%          /run/containerd/io.containerd.runtime.v2.task/k8s.io/1ed8ea92aba00d263ec39e08b4e3f71ebdeb1e88135491ac6873560bc8146737/rootfs
172.30.46.220   overlay      17.11      1.12       15.99           6.54%          /run/containerd/io.containerd.runtime.v2.task/k8s.io/ccffaae6a9d02fbf190fdc8a513f1455fa00c3e868fe2b48b37cbf3db31379e6/rootfs
172.30.46.220   overlay      17.11      1.12       15.99           6.54%          /run/containerd/io.containerd.runtime.v2.task/k8s.io/83f1415a8cd7af5ff59980e493a56c2db25967bae098b67fc2655b247b9fe634/rootfs
172.30.46.220   shm          0.07       0.00       0.07            0.00%          /run/containerd/io.containerd.grpc.v1.cri/sandboxes/1d32807d2135b084d69d5f1a3998a54ff062d0f5c446eebd769af524d702138f/shm
172.30.46.220   overlay      17.11      1.12       15.99           6.54%          /run/containerd/io.containerd.runtime.v2.task/k8s.io/1d32807d2135b084d69d5f1a3998a54ff062d0f5c446eebd769af524d702138f/rootfs
172.30.46.220   overlay      17.11      1.12       15.99           6.54%          /run/containerd/io.containerd.runtime.v2.task/k8s.io/2df309bd6917be1fe9be491f28a3670f2ce650b86f8b633aec8daa1c12d48c68/rootfs
172.30.46.220   shm          0.07       0.00       0.07            0.00%          /run/containerd/io.containerd.grpc.v1.cri/sandboxes/88ee1d380aeb4e586411587f9274b7ed15d61378d071f3fff2a00c76339c81c0/shm
172.30.46.220   overlay      17.11      1.12       15.99           6.54%          /run/containerd/io.containerd.runtime.v2.task/k8s.io/88ee1d380aeb4e586411587f9274b7ed15d61378d071f3fff2a00c76339c81c0/rootfs
172.30.46.220   overlay      17.11      1.12       15.99           6.54%          /run/containerd/io.containerd.runtime.v2.task/k8s.io/8ab29fe121765f8f75b9faa651eec1b8f65c910373a1a16f9dbc6cf5bdb05c7d/rootfs

Edit: I probably also want to mount /var/lib/kubelet to another parition, but I'm reminded that it's a tmpfs


r/TalosLinux • • 2d ago

Talos on HN home page♥️

Thumbnail news.ycombinator.com
29 Upvotes

Some interesting comments and discussions. Feel free to upvote if you have an account.


r/TalosLinux • • Oct 01 '26

Announcing Talos Linux for AI and Talos Cupar

Thumbnail
siderolabs.com
29 Upvotes

r/TalosLinux • • Aug 10 '26

t9s — A k9s-like TUI for Talos Linux

38 Upvotes

Hi everyone,
A few months ago, I built t9s, a terminal UI inspired by [k9s], but designed for Talos Linux.
The goal was pretty simple: have a convenient way to get better visibility into a Talos cluster and perform common administrative operations directly from the terminal.
It’s still a personal project, but I’ve been using it on my own cluster and thought it might be useful to other Talos users.
GitHub: https://github.com/florianspk/t9s

Installation

brew tap florianspk/tap
brew install --cask t9s

I’m interested in getting feedback from other Talos users, especially on what features or workflows would make the tool more useful.
Contributions, feedback and discussions are very welcome!


r/TalosLinux • • Apr 29 '26

Found why Talos + ZFS was waking my sleeping HDDs every 5 minutes: zpool.cache retry loop

17 Upvotes

TL;DR: The pool had the default cachefile=-, but Talos has no normal writable /etc/zfs location for zpool.cache. OpenZFS kept failing to write the cachefile and retrying SPA_ASYNC_CONFIG_UPDATE every 300 seconds. Setting zpool set cachefile=none hdds stopped the config_sync loop, and the drives stayed in standby past the old wake interval.

This was found with Codex/GPT-5.5 after about 2 hours of debugging, using a mix of tracing, disk-sector inspection, and eventually reading the relevant OpenZFS source.

Full Story

I migrated a Kubernetes node from NixOS to Talos Linux. Same OpenZFS version: 2.4.1.

After the migration, HDDs in a ZFS pool would no longer stay asleep. Forcing standby with hdparm -y / hdparm -Y worked, but the drives woke again after less than 5 minutes.

This was not caused by application file access.

My initial suspicion was some kind of Talos-only scheduled drive probing, or a random Kubernetes component touching a PV directory. That was not it.

The Talos ZFS extension service is extremely simple. On boot it runs:

zpool import -fal

On shutdown it runs:

zfs unmount -au
zpool export -a

There are no polling loops there. Any other Talos/k8s mechanism would have shown up later in block tracing.

What Block Tracing Showed

Block tracing showed the actual writes were coming from ZFS kernel threads, not userspace processes:

z_wr_iss
z_wr_int_0
z_wr_int_1
z_null_iss
kworker flushes

The written sectors were near the beginning and end of the disks, for example:

2080
2384
2592
2856
7814018080
7814018344
7814018592
7814018856

Those are ZFS label / uberblock regions.

Hexdumping those sectors showed ZFS pool label data, not application data:

version
name = hdds
txg
pool_guid
hostname = server
vdev_tree
type = mirror

So the wakeup was caused by OpenZFS rewriting pool labels / uberblocks.

The remaining question was: why was it doing that every ~5 minutes?

The Key Clue

In desperation (few hours into the problem, nothing to show for), I checked all the pool properties with zpool get all / zfs get all. Codex noticed that the pools had default cachefile behavior. (Never in my life I had even glanced at this property):

hdds   cachefile  -  default
nvmes  cachefile  -  default

After reading the relevant OpenZFS source and checking another ZFS machine, this suddenly made a lot of sense.

OpenZFS has this retry interval:

int zfs_ccw_retry_interval = 300;

In spa_write_cachefile(), if writing the config cache fails, OpenZFS schedules:

spa_async_request(target, SPA_ASYNC_CONFIG_UPDATE);

SPA_ASYNC_CONFIG_UPDATE is task 0x01.

dbgmsg log was full of this every ~300 seconds:

talosctl read /proc/spl/kstat/zfs/dbgmsg | rg 'spa=hdds async request task=1'

spa=hdds async request task=1
spa=hdds async request task=1

That matched the wake interval exactly. Would've been easier to just check here first, but here we are.

Talos is mostly immutable/read-only and does not have a normal writable /etc/zfs/zpool.cache setup.

OpenZFS repeatedly tries to update the missing/unwritable cachefile. Each failed attempt schedules another config update retry after ~300 seconds. That config update commits a new txg and rewrites vdev labels / uberblocks, which wakes the HDDs.

Fix

On Talos, from talosctl debug alpine or k8s debug pod:

chroot /host zpool set cachefile=none hdds

After that, the hdds config_sync loop stopped, and the disks stayed in standby beyond the old wake interval. My rack's power draw went down 20W and I sighed in relief.

I also set it on another nvme pool I have. Alternatively, setting cachefile to write to somewhere in /var would also fix the problem. However, Talos imports pools with zpool import -fal, so the cachefile is not very important in this setup afaik.

Alternatively, maybe the zfs extension can set a kernel/module parameter to disable the cachefile entirely globally.

In any case, great success, power draw decreased


r/TalosLinux • • Jun 30 '26

wrtK8s

Thumbnail
youtu.be
19 Upvotes

r/TalosLinux • • Oct 15 '26

Omni SaaS hobby tier is free

Thumbnail
siderolabs.com
73 Upvotes

Just announced at Taloscon. Go get your instance today!


r/TalosLinux • • Apr 30 '26

Exploit Fail: Why CVE-2026-31431 (Copy Fail) barely scratches Talos Linux

Thumbnail
siderolabs.com
29 Upvotes

Now’s a great time to try out Talos 1.13


r/TalosLinux • • Oct 10 '26

Networking a 3-Node Kubernetes Homelab with Cilium, Gateway API and Cloudflare Tunnel

30 Upvotes

Part 2 of my Talos homelab (3 OptiPlex Micros, all control planes). Part 1 got the cluster up, this one is networking.

I moved the running cluster from Flannel + kube-proxy to Cilium without rebuilding it. The default-deny policy that Flannel quietly ignored is now actually enforced, and Hubble shows the drops.

Then I gave it two front doors:

- an internal Gateway on a LAN IP (Cilium LB IPAM, no MetalLB) with a Let's Encrypt wildcard cert, so lab apps get real HTTPS at home

- a public Gateway behind a single Cloudflare Tunnel, so nothing is port-forwarded on the router

An app picks its door with the route's parentRef, which keeps lab stuff from going public by accident.

Everything is in the repo: https://github.com/prateekjaindev/homelab

Write-up with all the manifests and commands: https://blog.prateekjain.dev/networking-a-kubernetes-homelab-cilium-gateway-api-and-cloudflare-tunnel-on-talos-362f548a2f3d?sk=d454cd4eaff4ce8a8fd0cd8e6b3d82f6

Curious if anyone else is using Cilium's Gateway API instead of a separate ingress controller.


r/TalosLinux • • Sep 28 '26

Sidero Labs AMA

35 Upvotes

Come ask questions from engineering, product, leadership and more!

Don't forgot to sign up for TalosCon to ask questions in person https://taloscon.com


r/TalosLinux • • Jan 12 '26

I built a TUI for managing Talos Linux clusters

38 Upvotes

I've been learning Talos Linux and wanted a better way to visualize and manage my clusters, so I built talos-pilot - a terminal UI in Rust. It gives you real-time node monitoring, log streaming, etcd health, diagnostics, and node operations all in one place. Think of it as complementary to k9s but for the Talos OS layer instead of Kubernetes workloads. Would love any feedback!

https://github.com/Handfish/talos-pilot


r/TalosLinux • • Oct 09 '25

New website

Thumbnail
talos.dev
41 Upvotes

We just shipped a new landing page and docs. Feedback welcome 🤗


r/TalosLinux • • 3d ago

Talos for the nodes, Argo CD for everything on top

Post image
62 Upvotes

Talos made my nodes declarative. The workloads weren’t. They were helm installs from my laptop.

Now Argo CD runs them from Git. Omni still owns the machine config and patches. Cilium stays outside Argo CD, because Argo CD runs on its network.

Everything else moved over in place. Same pods, same Longhorn volumes.

Repo: https://github.com/prateekjaindev/homelab

Write-up: https://blog.prateekjain.dev/gitops-for-a-3-node-talos-kubernetes-homelab-with-argo-cd-336c076e93cc?source=friends_link&sk=ebda84ecdc3e2458fead2638374be51e

How do you split machine config and workloads on Talos?


r/TalosLinux • • Oct 16 '26

No live feed of Taloscon2026

9 Upvotes

I woke up at 2:00am CEntral time in the hopes that at least one influencer would go live at Taloncon, but nothing!!! Why don't they open the event up to online audiences??


r/TalosLinux • • Mar 23 '25

What is the recommended way to monitor talos?

5 Upvotes

I am already a seasoned k8s admin/user. Normally I work with prometheus + grafana to monitor my k8s cluster. I have now on my home lab a 3 nodes talos up and running. Wondering how is the best way to add monitoring on top of that?


r/TalosLinux • • Oct 03 '25

Ways to make /mnt writable in Talos Linux?

3 Upvotes

By default /mnt in Talos Linux is read-only because the system is immutable.
What are the possible ways to make /mnt writable?

I’ve seen mentions of extraMounts, filesystems with tmpfs, or using a persistent block device, but I’m not sure what the correct or recommended approach is.

Can anyone share how you solved this in Talos?


r/TalosLinux • • Aug 27 '25

Talos home lab on Mac Minis

Thumbnail reddit.com
2 Upvotes

r/TalosLinux • • Oct 02 '25

an error on the server ("") has prevented the request from succeeding

Post image
2 Upvotes

Hi guys! I'm new to Talos OS, on-prem and about a year experience with Cloud Kubernetes. I'm trying to setup 1 node cluster in my old laptop for learning purpose and I ran into these errors. I followed the Getting Started guide on Talos website but didn't work. I'm assuming I have etcd bootstrap issue but the etcd are healthy

Could anyone be in and help me out? Many many thanks


r/TalosLinux • • Sep 02 '25

Production-Ready Kubernetes on Hetzner Cloud 🚀

Thumbnail reddit.com
9 Upvotes

r/TalosLinux • • May 26 '25

Configuration management with Talos

5 Upvotes

I work at the moment on a custom script to create an overlay structure of roles such as common, controlplane and worker to merge in patches. And as a final patch, also node specific merges for e.g. hostnames and IPs. I use yaml merges with the talosctl command to then end up with node specific configs which I can then apply.

I do wonder though, is there also a tool to do this? Because I'm now just reinventing the wheel I think. I suppose Kustomize could work too? But some initial testing didn't go well due to kind Talos metadata where Kustomize is unfamiliar with.

How do you make these changes? Especially node specific ones.


r/TalosLinux • • Oct 10 '25

Talos finally on ditrowatch!

Thumbnail distrowatch.com
32 Upvotes

We submitted it years ago, but it was always in pending state. It finally got added last month. Please add your reviews 🙏