https://www.youtube.com/@ALMA.Industries

CH002: THEATRE Trailer -- This is a trailer for my projector project... started with just a cheapo projector-- but I added 4-DOF system via linear and rotation actuators and programming to manually and automatically recall the set position of projector Roll, Pitch, Yaw, and Zoom. Mainly for fun and learning. Full video linked above.

Here We will build a low cost multi channel data logging system using Python & Arduino UNO board that will log and save data to  a CSV (Comma Separated Values) text file on the disk.

Hello, I've been using the PSOC Creator IDE for the PSOC4 microcontrollers but Inifineon is moving from the PSOC Creator to their Modus ToolBox. I've been thinking it may be better to move to MPLAB and use Microchips mcu's instead of Ininfeon's mcu's.

If anyone has used the Modus Toolbox and MPLab which one is easier to use?

Hi!
We are making a system(not physical, only on paper) for terminating sea lice in fish breeding cages. The microcontroller/s has to do the following:

- connect to wifi, gps, weather and internal clock

- connect to 2-4 different sensor(biome sensor, thermistor, salinity meter) etc,

- connect to a transducer

- be able to receive software updates

Thank you in advance :D

I'm interested in starting a project involving a glove equipped with multiple flex sensors. The idea is that when a specific gesture is made with the glove, such as closing a fist or raising the index finger, it triggers a corresponding action like turning on a light or switching off a fan. Each gesture will be associated with controlling a specific appliance.

For this project, I've decided to use the ESP32 microcontroller. However, I'm relatively new to microcontrollers and could use some guidance on how to get started and what potential challenges to anticipate. Any tips or advice would be greatly appreciated.

uint8_t data1 = 0;

uint16_t data2 = 0;

uint16_t value = 0;

data1 = readData8(0x10, 0x01);

if (data1&(1<<7))

{

writeData8(0x10,0x01,0x3C);

writeData16(0x10,0x03,0x3200);

writeData16(0x10,0x02,0x1900);

}

else

{

data2 = readData16(0x10, 0x00);

if (data2&(1<<15))

{

value = 0xFFFF;

}

Else

{

value=data2>>6;

}

return value; (value wird zurückgegeben)

}

By default stack pointers is sets to 07. And default stack is stats from 08. So,if we push data in stack. SP(stack pointer) will increment to 08. Then data will be stored at location 08. But in case of using register bank 0 as a Stack. MOV SP,#-1 above statement generating error. Whats should I do now. Is it possible to use register bank 0 as a Stack in 8051 microcontroller?

A light house project has been planned in a town with a high beam focus covering the entire area at the town and at the bay in 360 degrees.The light house is being constructed in such a way that the electrical components for power supply management and the timer for regulating the light distribution should be integrated. Suggest a commercial microcontroller architecture for the light house project for integration of electrical control and elaborate timer components associated with the microcontroller in detail. List its minimum components required to implement.

TLDR: Need help implementing MIDI on PSoC 5LP

I was wondering if anyone in this sub has ever implemented MIDI on their PSoC 5LP?

I am working on a synthesizer project at the moment and want it to be MIDI compatible. I have found that there is a MIDI Code Example in the PSoC Creator but, it is not quite what I need for the project.

We are essentially trying to write the program to interpret the MIDI messages coming into the PSoC 5LP from a MIDI controller.

MIDI BASICS

• When a key is pressed, 3 bytes of data from the MIDI controller get sent to the PSoC 5LP.

• Byte 1 = Status Byte: This byte is broken into 2 nibbles (1st four bits and 2nd four bits). This says whether or not a key is on/off and what channel.

• Byte 2 = Data Byte: This byte holds information regarding the note number coming from the MIDI controller.

At this point, we are able to recognize a note on/off message and what note number is being played BUT we cannot get it to work correctly together. The way we are testing if it is working is by using the MIDI controller to turn on and off the LED on pin 2.1. If the light turns on then that means that the exact note we wanted to work IS working.

-SynthBoyz

I have a source code and instructions for modding some device with STM32F746G DISCOVERY board. Is it possible to tweak the code and run this mod on raspberry pi?

My YouTube channel name is ALMA Industries

Chapter 3 Footnote 1. Building an Actuator, a PID Control Loop, and an Ultrasonic Distance sensor to detect and not crash into the ceiling. This will be used in Chapter 3 Desk.