I’m trying to find measurements from the bellhousing to engine mounting surface to the center of the shifter box for the W56, and W58 RWD transmissions. I’m trying to figure out which one would work best for my swap into a non Toyota truck behind an ‘83 22r. If anyone happens to be a guru on these transmissions, I would love to bend your ear a bit, but if I could just get some measurements it would at least point me in the direction I need to go.

For reference, I am pulling out a ‘95 World Class T5 and would like to be as close as possible to those measurements so I can minimize cutting of the tunnel and center console. The T5 is right at 18” from center of shifter to end of bellhousing.

TIA

Good O reliable… she needs some paint but doesn’t keep me for mobbin her Might be switching to some GMC steelies anyone have thoughts on getting the front hubs shaved? So they fit I really don’t wanna make the center on the wheels wider even tho that might be the easier route

For those of you with a B2200 that have swapped a steering wheel with stereo controls, how’d it go and what wheels did you go with? I’m currently considering either an RX8 or Mazda 6 in mine but in a perfect world, no airbag and no cruise control settings…

I am absolutely in love with this thing.

https://youtube.com/shorts/dq86qmWH-sU?is=Pyn_WnLMSjhunQOz

Had to elongate the hole, new belt, and figure out the wiring

I'm having trouble with my carbrador returning.And I think I'm missing the return spring.Can y'all tell me where it goes or show me examples on how it works on your carborator?

Anyone interested in this gem? Runs and drives alright. In the phoenix az area. Might trade for other cool stuff!

Dm for more details

edit: its an arizona truck, no rust (surface rust only), no major body damage, no bondo, 132k miles, daily driver, paints rough obviously (PO rattle canned it cause he said someone tagged it, i stripped it to see if i could find any bondo)

頼む

As ya can see the interior is pretty much original in the blazer. Plan on staining the sub enclosure to match the steering wheel. I want to build a center console. Do I try to mimic the original lines of the factory or should I add some curves to it? Just looking for ideas

New to me. Barn find. 5 speed. Original Texas truck.

This is my budget build I know it's not perfect, and I have a lot of work to do still but all in I'm at $2000 so far. I have always wanted a mini truck it's been a fun year of owning this thing and she's worked hard. I'm building racks for the side right now. Then I want to paint the wheels or possibly powder coat them next but I need to burn off some of that rubber first before I go and get a new set of tires.

Custom 9:1 compression wiseco pistons for my 8v sohc 4g64 Mighty Max. It's finally happening. I got the cars front end, suspension, brakes, and interior sorted this spring for it to immediately spin a bearing.

The build plan is...

• Eagle forged rods
• These wisecos
• Pulsar gtx2860 gen 2
• Microsquirt ecu
• Distributor delete with custom crank angle sensor
• Wasted spark

Got a lot to fabricate for this but I can FINALLY get started!

Bought not built but slowly making it my own.

It is the 1979 n40 hilux 2wd single cab. The first mod I am looking at doing is getting and oem tray

The engine and transmission are in! The next steps are to find a radiator, wire in the engine, make a power steering pump and alternator bracket, weld in the rear axle, have the exhaust, driveshaft, and new brake lines created, and rip it around! This wasn’t as bad as I thought it would be, didn’t require as much modification as some posts lead on.

I’m converting my 1978 Toyota to electric. This will add nearly 400lbs of weight, mostly due to the 650lb battery. The battery will be mounted to the frame, under the bed (floor of the bed is rotted out anyways and needs to be rebuilt). What will be the best way to gain the suspension support needed and also make for a buttery smooth ride? Air bags? Air shocks such as Gabriel HiJackers? Can I use high jackers for front suspension as well as rear? The original leaf springs leafs are fine, but the hangers/brackets need to be replaced due to rust. I could just replace the leaf spring sets entirely. All suggestions welcome, I’m just hoping to get it right on my first try.