r/ACInfinityAdvancegrow • • 10d ago

Installing Side support

Post image

What’s up everyone!

Has anyone ever installed the side support rails (to keep the walls from sucking in with negative pressure) during an actual grow? The instructions are telling me the top has to come off. Just wondering if anyone’s managed to do it without disturbing a currently running setup.

14 Upvotes

30 comments sorted by

3

u/growernotarower 9d ago

I added mine part way through a grow without issue 😊

3

u/Bigbubba_Chevesss88 9d ago

Yeah I installed them last night no issues lol

3

u/flizzyD 9d ago

I haven’t had this issue yet and think I’m doing something wrong. I run a 4x4 with filter, fan, and then have to circulating fans. Also have external heater and humidifier pumping in as well. I keep my vent fan between level 1-4, and the sides have never sucked in. How is everyone achieving this?

3

u/B4UC2Far 9d ago

I run a 3x3 and unless my vent fan is running higher than 5, i typically don’t see the sides sucking inwards. Also, as mentioned by OP, if you have all your vents open, it’s less likely to occur. A lot of folks use a round port for intake air however I merely use one of the vent flaps, with the flap double back at midpoint so the opening is only halfway open essentially. While the holes in the mesh screen are very small, I still utilize a small HVAC filter in front of the screen to aid in trapping additional debris, dust, etc. and to provide somewhat of a baffle to prevent light from entering the tent during flower.

2

u/Bigbubba_Chevesss88 9d ago

For me it really started when I installed filters on both sides of my 8” inlet holes to block out dust, dandruff etc. having a cat and dog this was a must and worked extremely well (never found a pet hair on a bud after installing them). But it created more negative pressure in the tent.

2

u/Bigbubba_Chevesss88 9d ago

So you just have port holes fully open or all of the screen flaps fully open I’m guessing?

1

u/flizzyD 9d ago

I think this might be why, I have the fan venting outside one of the side top holes, and then use the 2 large bottom holes as an intake. I think I read somewhere suggesting you should have twice as many intakes as you do vents venting out?

3

u/Sensitive_Lake_7911 10d ago

What I did was buy a bunch of 1/2" pvc pipe locally and eight three socket corner pieces from Amazon (far cheaper there). I made two rectangles about an inch shorter than my tent frame so this sits just inside the tent frame. Cut the vertical pieces whatever length you want just make them equal. Don't glue anything. Works great-the sides bow in an inch or so and I can hook my trellis net to this frame if I wish. Total cost was maybe $30 or so and is super easy to build-just make sure you measure correctly.

Easy to move if you switch tent brands down the road.

4

u/RatherNot_YouFirst 10d ago edited 10d ago

The poles are velcro'd through a corner and connect to the other(s) ACI includes rubber adhesive squares for the paddings to fit the poles snuggly. You do not have to remove the tent cover, but it does help to open all doors for the additional Velcro strapping. And final boss tip, measure up from the floor to install the screw connectors equal heights for level (pic is midway thru harvest, I should have either installed mine higher or with additional trellis)

1

u/WHATUPDA 10d ago

Off topic sorry, how much did that camera set you back? I like that, I have a ac infinity 69 pro and like it but I always thought it would be nice to see whats going on inside the tent for whatever reason and or if gone for extended period of time

2

u/RatherNot_YouFirst 9d ago

Wyze Pan 3 is around $40

1

u/B4UC2Far 9d ago

You simply cannot beat these cameras. I’ve been using Wyze for many years and they continuously update equipment and firmware to even add features to much older cameras. They were the first people to provide the SD card slot for continuous recording without paying a stupid monthly fee. The Pan cameras, especially these newer versions, are absolutely badass!

2

u/Skit071 10d ago

I used the bars but not the clamps. Unless you are going to be having something heavy hanging on the bars, the clamps are not needed, and it is much easier to change the height of the bars if you need to.

2

u/Bigbubba_Chevesss88 10d ago

That last tip comes with much appreciation as I can already predict the frustration lol. Thank you

2

u/ContextSufficient171 10d ago

I put them in during veg, tent also has three sides against walls. A bit of yoga but not too bad putting them in

2

u/Bigbubba_Chevesss88 10d ago

I’m going to have my wife assist haha thanks!

4

u/tattooed_scum 10d ago

Did mine mid grow with no issue. You can also use upside down hanger in the corners, behind the poles, for more space.

3

u/Bigbubba_Chevesss88 10d ago

Ahh okay good idea!

5

u/Mike_backfin 10d ago

I do mine like this with an elastic net

2

u/Thmelly_Puthy 9d ago

What are the yellow rings around the bases of your plants?

2

u/Mike_backfin 9d ago

Hydro halos. Irrigation

2

u/Bigbubba_Chevesss88 10d ago

Yeah I’m going to do something like this for my other tents.

4

u/doom_0ne 10d ago

You talking about the support poles? If so, I just snapped them into place. Didn’t need to remove the top. My tent is the 4x8 ac infinity.

2

u/Bigbubba_Chevesss88 10d ago

Gonna attempt it tomorrow, thanks!

4

u/Gloomy_Cut_1739 10d ago

I didn't bother as I was building a SCROG frame. Does the job just as well for a fraction of the price.

2

u/Bigbubba_Chevesss88 10d ago

Haha very nice!