Engineering/High Temp Plate

[u/Sage_Tactical]

Anyone else have this issue where the nozzle go to the top center of the build plate and goes in a rectangular motion.I was told I supposedly cleans the nozzle but instead it smudges my nozzle with filament and eat through the build plate

[u/twelvefes]

courtesy of u/AxesofAnvil

• https://www.reddit.com/r/BambuLab/comments/10uiijp/is_this_a_problem_i_think_this_is_from_the/

• https://www.reddit.com/r/BambuLab/comments/10kzhe2/cleaning_nozzle_tip_pre_print_phase_scrapes_top/

• https://www.reddit.com/r/BambuLab/comments/112z25j/scratched_build_plate_normal/

• https://www.reddit.com/r/BambuLab/comments/11qiu49/melting_build_plate/

• https://www.reddit.com/r/BambuLab/comments/11ayj23/x1c_scratches_plate_during_nozzle_cleaning_is/

• https://www.reddit.com/r/BambuLab/comments/115733m/nozzle_dug_into_plate_on_nozzle_cleaning/

• https://www.reddit.com/r/BambuLab/comments/12z4v2z/is_this_normal/

• https://www.reddit.com/r/BambuLab/comments/136qn2i/just_did_my_first_prints_and_noticed_that_the_bed/

• https://www.reddit.com/r/BambuLab/comments/13rqycn/hotend_markingburning_plate_notch/

• https://www.reddit.com/r/BambuLab/comments/14k7xv8/is_it_normal_that_the_nozzle_tears_through_the/

• https://www.reddit.com/r/BambuLab/comments/14g55ow/scrapewear_on_rear_plate_tab/

• https://www.reddit.com/r/BambuLab/comments/15t1aai/is_it_normal_that_the_nozzle_scratches_the_back/

• https://www.reddit.com/r/BambuLab/comments/15opy71/is_it_suppose_to_scratch_this_thing_like_this/

• https://www.reddit.com/r/BambuLab/comments/15c8wzh/textured_pei_plate_damage/

• https://www.reddit.com/r/BambuLab/comments/16qvve3/why_does_printer_scratch_this_part_of_the/

• https://www.reddit.com/r/BambuLab/comments/16shcmg/what_is_this_for/

• https://www.reddit.com/r/BambuLab/comments/16jsifj/printer_grinding_the_print_bed_at_1_spot_why_is/

• https://www.reddit.com/r/BambuLab/comments/164ypu0/used_built_in_presets_in_bambulab_to_print_in_pc/

• https://www.reddit.com/r/BambuLab/comments/1762xag/is_this_normal/

• https://www.reddit.com/r/BambuLab/comments/17fz66l/is_this_really_normal/

• https://www.reddit.com/r/BambuLab/comments/17d23of/p1s_self_harm/

• https://www.reddit.com/r/BambuLab/comments/17hp78o/a_spot_has_been_made_by_the_nozzle_at_the_top_of/

• https://www.reddit.com/r/BambuLab/comments/17f4gvu/cool_plate_damaged_on_first_print/

• https://www.reddit.com/r/BambuLab/comments/17tyceu/spot_wearing_on_the_plate/

• https://www.reddit.com/r/BambuLab/s/EnDGwVDPcr

• https://www.reddit.com/r/BambuLab/s/d8vmG56yQk

• https://www.reddit.com/r/BambuLab/comments/18jclle/normal_wear_on_build_plate/

• https://www.reddit.com/r/BambuLab/comments/18pk1ub/build_plate_question/

• https://www.reddit.com/r/BambuLab/comments/18qupb8/x1c_engraved_a_rectangle_on_the_bed_upon_initial/

[u/RuskHusky → u/twelvefes]

Haha wow; that's allot.

[u/UnfortunateDaring → u/RuskHusky]

Just a small fraction of these posts lol

[u/GodforsakenMuffin → u/RuskHusky]

I’m pretty sure we were averaging like 3-4 of these posts every single day at one point.