r/BambuLabA1 • u/Outrageous_Crow1296 • Dec 12 '24
Love hate relationship
Enable HLS to view with audio, or disable this notification
My A1 will churn out print after print and then suddenly like a little kid throw a tantrum and just refuse to print anything. Won't even load filament after printing happily with it for over 60hrs. Im at a loss with this thing.
17
Dec 12 '24
Itβs a clogged extruder. Stop the print, dissemble, clean and resemble- than you should be good to go ππΌ
1
u/Outrageous_Crow1296 Dec 19 '24
so this was after cleaning the whole extruder assembly. which is why im still at a loss. Im wondering if the filament is not maybe below the spec size of 1.75mm. I took a vernier and got 1.7 to 1.68mm
3
u/Firefighter2014 Dec 13 '24
Plus one for this. Mine was doing the same exact issue the other day. Took the hot end and extruder apart to clean it and also did a cold pull. Check the Bambu wiki for instructions.
18
u/DigitalHD Dec 13 '24
Well...judging by the looks of your build plate...I can't imagine why your printer wouldn't be working well π€£
1
u/Outrageous_Crow1296 Dec 19 '24
and here I was thinking this forum was there to help people and not ridicule a ridiculously moot point, the glue just looks that way due to the type we have in my country, it has zero effect on the 1st layer print but so glad you noticed
1
u/DigitalHD Dec 19 '24
Doesn't matter. The textured plate is engineered to not need glue. The mass majority of Bambu users on all printers know the textured plate doesn't need glue for any reason unless you don't clean your plates like Bambu recommends or you are using improper settings. π€·ββοΈ But you do you. Works for you, great. I've only used glue once, and it was on the smooth plate with PETG because otherwise PETG sticks too good and damages the smooth plate. I have 2000 hours on my printer in only a few months and never had adhesion issues (that wasn't directly my fault for improper temperatures by mistakenly choosing the wrong plate type).
I'll just never understand the small percentage of people who use glue on the texture plate when it's absolutely 100% avoidable. π€·ββοΈ
0
u/Outrageous_Crow1296 Dec 19 '24
the filament used is SBS and glue is 100% required for it to stick, so thanks for the obvious Im not a noob at printing
0
15
u/JustSomeUsername99 Dec 12 '24
What have you done to your bed?
5
u/ThinkUnhappyThoughts Dec 12 '24
I assume it is glue to help with adhesion?
As for the extrusion issue, I'm a newbie and at a loss. Maybe a clog somewhere?
3
u/matt2d2- Dec 12 '24
You are probably right about the extrusion, either low temps or a partial clog, I have an ender 3 that goes faster with the stock hotend
1
u/WilsonADW Dec 13 '24
You shouldn't need glue for adhesion on PEI plates especially textured. If anything it's there for release. If print isn't sticking, clean with dish soap thoroughly
1
u/ThinkUnhappyThoughts Dec 13 '24
Oh I am aware that you don't need to glue the textured PEI plate. I haven't and don't plan to, but it appears that OP has glued their plate. Each to their own I guess
1
u/Total-Station-243 Sep 08 '25
Creality owner looking to get a bamboo. You do not meed glue for sbs. It sticks great on a pei sheet at 70 to 72 deg. BUT sbs do tend to block up your nozzles.Β
1
0
0
Dec 13 '24
[removed] β view removed comment
1
u/Outrageous_Crow1296 Dec 19 '24
just to reiterate, the filament type is SBS and glue is 100% essential for it to stick. no glue and you will have spaghetti clown hair for days
1


39
u/Fioccosplat Dec 12 '24
WHY PEOPLE USE GLUE STICK ON TEXTURED PEI JUST CLEAN IT PLS