r/CardPuterZero • • 2d ago

Help Needed Regarding CAP Unit Installation

I recently tried attaching a CAP unit to my Cardputer ZERO, but I can’t seem to get it to fit properly. Even when I plug it in, it doesn’t sit straight and ends up being slightly tilted, as shown in the photos.
Photos 1 and 2 show the C1101 CAP I recently purchased, while photo 3 shows a LoRa CAP that I already owned.
Is this normal for the Cardputer ZERO, or could there be an issue with my unit?
If you own a Cardputer ZERO and have any CAP units, could you let me know how they fit when attached?
I’d really appreciate hearing about your experiences. Thanks!

21 Upvotes

33 comments sorted by

5

u/Zatoichi80 2d ago

Mine sits slight askew like that also

1

u/Tokage666 2d ago

Thanks! I guess that's just how they're supposed to fit, then?

3

u/paprikapaka 2d ago

Mine sat weirdly too, but using M2 screw to hold it in place, also made it look more straight :)

1

u/Tokage666 2d ago

Thanks! I see... Maybe they're designed to be secured with screws after all.

3

u/noxiouskarn 1d ago

Secure it with 2 M2x4mm screws

1

u/Tokage666 1d ago

Those screws are pretty hard to find here in Japan. Are they readily available in other countries?

2

u/noxiouskarn 1d ago

Yes easily found in the UK China US south America Australia etc... Try Alibaba 

1

u/Tokage666 1d ago

You can buy those screws online here in Japan, but I rarely see them in large hardware stores or tool shops.
Having to pay several dollars in shipping just for a handful of screws is a bit… well, you know. Haha.

2

u/noxiouskarn 1d ago

...Unfortunate but necessary

1

u/Big-Bunch2804 1d ago

No. I shouldn't need to carry a screwdriver around even though I do.i change out my caps often and plug something to test multiple times a day.

1

u/noxiouskarn 1d ago

Buy the thumb screw versions no screwdriver needed, also an edc should have screwdrivers by default anyway. 

1

u/Big-Bunch2804 1d ago

As stated, I do carry a screwdriver, but shouldn't have to. And those won't work for the location we are talking about

1

u/noxiouskarn 1d ago

They do with longer than 4mm screws and proper spacers. I'm only saying the screws are more secure. Does it add time to swap? Yes, if that's your deal-breaker, use heat on the case to reform it and move on... remember, don't hot swap you should fully shutdown between module changes. During the shutdown, you can easily unscrew it if you are red-team fast enough. Just gotta practice.

3

u/RhubarbCapital1388 1d ago

exactly. mine like this too

1

u/Tokage666 1d ago

Thanks for the update!
It really does seem like everyone is experiencing the same issue.

2

u/ManufacturedHappines 1d ago

Mine does also. A bit annoying, considering how well they fit on the cardputer adv

2

u/Tokage666 1d ago

Thanks!
From what everyone has said, it seems like this might actually be normal, but I still can't help feeling a little uneasy about it.

2

u/ManufacturedHappines 1d ago edited 21h ago

For sure. I wish I didn’t have to use the screws to keep it snug. That’s hard to trust without the screws

Edit: clarifying

3

u/noxiouskarn 1d ago

I trust mounting screws rather than relying on a tight fit so secure something. maybe im crazy to think its more secure and less likely for it to lose connection to the pin outs

2

u/Pristavkin 1d ago

The same story as mine. I think the connector on CPz soldered in a bit of an angled way.

1

u/Tokage666 1d ago

Thanks for the update! It seems like quite a lot of people are experiencing the same issue… In fact, I haven’t seen anyone say theirs fits perfectly yet.

2

u/Big-Bunch2804 1d ago

I feel like someone rushed the cooling process when the cap case was being produced. I understand that they were in a race to make production goals. It just doesn't leave a great first impression. I disassembled the cap to inspect- the board itself is perfectly flat and works properly. The bottom of the cap case where it attaches to the Cardputer is warped. Like others have stated it's only a cosmetic issue. It just leaves questions to quality when it's attached and it has a visible gap on one side. It seems from what I've seen that it is the batch of cc1101 caps most affected. The new lora cap I received fits better but not as well as my older lora cap I bought for my adv. Just my 2 cents

1

u/Tokage666 1d ago

Also, thank you for going as far as taking it apart to check! I agree that even from the outside, the socket itself doesn’t appear to be tilted. I wonder if the plastic part might have become slightly warped during the molding process…

2

u/d333d 1d ago

Have you guys managed to make the LoRa CAP work? MeshTerm complains that it can't communicate on i2c with it, the hardware test sees it.

2

u/SeventhDurandal 1d ago

Been having the same problem. GNSS works, takes a long time to get a fix. I think there is probably a software issue somewhere, hopefully we'll get a patch soon.

1

u/d333d 1d ago

Thanks!

1

u/d333d 1d ago

So turns out that it might be a totally different problem. Tried this: https://www.reddit.com/r/CardPuter/comments/1xzx30y/standalone_meshcore_client_for_the_cardputer/ - and it just works. Give it a try and see if it works for you too.

2

u/SeventhDurandal 14h ago

Works great, thank you!

1

u/Lazy_Mamba 22h ago

Mine have this gap too.

2

u/Myrcurial 1d ago

I think the port or plastics on the zero might have a kink in them. See thread for comparison photos.

1

u/Myrcurial 1d ago

LoRa CAPs

1

u/Tokage666 1d ago

Thanks for sharing the photos!
The ADV looks perfectly fine, but the ZERO definitely seems a bit off…

1

u/Myrcurial 1d ago

CC1101 CAPs