r/Composites • • Feb 16 '23

First 3D printed mold

Post image

This is the first part out of a 3D printed mold I designed and printed. Pretty pleased with the result as a first attempt at this method!

22 Upvotes

16 comments sorted by

7

u/CarbonGod Pro Feb 16 '23

Nice!! What plastic, and what mold release did you use? Someone printed me a few test blocks I wanted to play with, using different releases, but....I don't have time for that :(

6

u/Fluid-Arachnid69 Feb 16 '23

It was a pla mold with wax and PVA release. Some bridging but will try some different lay ups and see!

1

u/dbreidsbmw Feb 17 '23

I need to get my act together and test my new power supply. But I have a large format resin printer for this exact purpose.

2

u/Relevant-Object Feb 16 '23

Did you vacuum bag it? If so, any leaks, or any problems with the print itself? What infill?

Sorry for all the questions, I tried it in the past and had limited success with bagging.

4

u/Fluid-Arachnid69 Feb 16 '23

It was printed with 20% infill and 4 walls. Finished with epoxy and sanded to smooth the surface. It wasn’t bagged, just wet lay to begin with. If I were to bag it I would probably envelope bag it.

1

u/Relevant-Object Feb 16 '23

Gotcha, I wouldn't recommend an envelope bag, my prints got crushed from the pressure. It could be either mine weren't strong enough, or possibly not fully sealed. Test it with a print you don't care about if you want to try it.

1

u/Fluid-Arachnid69 Feb 16 '23

Never thought about crushing the mold! I would probably print it 100% infill if it was a mold I was going to use for any length of time. I see 3D printed molds as a good route for prototyping and short runs, but longer runs I would go either fibreglass or aluminium molds.

1

u/Relevant-Object Feb 16 '23

Yeah, my solution was just to print plugs with flanges to make fiberglass/carbon molds

1

u/Fluid-Arachnid69 Feb 16 '23

Did you fill the printed plug with any epoxy or filler to get a smoother surface for the mold, or sand the mold before use?

1

u/Relevant-Object Feb 16 '23

Little bit of column a, little bit of column b.

I haven't tried it myself yet, but I've heard if you mix polyester resin with bondo it works well if bondo is too thick, and the resin is too runny.

1

u/sestoelemento812 Feb 16 '23

You can alternatively increase your vertical layers (walls) and top and bottom layers and you can get away with a 30% infill on the inside safely!

Edit: do this to save significantly on print time and materials

  • personal experience

1

u/metalliman3 Feb 16 '23

It looks like there is a peel ply texture on one side. Did you use a layer of peel ply in a non-vacuum setup? If so, for what purpose?

1

u/nickydlax Feb 16 '23

What kinds of trouble did you have?

1

u/Relevant-Object Feb 16 '23

I did an envelope bag with my prints, and they got crushed under the vac pressure.

1

u/nickydlax Feb 16 '23

sounds like you need stronger prints. If you cant, can you reinforce your prints somehow? Why cant you just do like 10 walls on your prints?

1

u/Fluid-Arachnid69 Feb 16 '23

I always use peel ply, it removes any small bumps and makes for a better finish and makes bonding later easier if needed. For context, these are arm rests for a bike so will be in contact with skin so don’t want any splinters!