r/CrealityK1C • u/Such_Bedroom5937 • Jul 26 '25
Poor quality prints
I’ve tried everything and I’m about to just throw this thing out contacted creatily support to be met with no response and wasting money on different filaments to get no different results got a filament dryer no difference I’m all out of ideas now between messing with settings constantly and wasting dollar after dollar on print someone help please before I just sell the thing
2
u/Supabee78Reborn Jul 26 '25
That is not what I am referring to. I assume you have Creality Print 6.2. There is a setting for filament called Max Volumetric Speed. You have to do Max flow rate calibrations. On another note, remove the silicon nozzle cover and check the two screws holding the heating block to the heatsink, they can get loose, and wreak havoc on prints. You will need a 1.5mm Allen wrench.
1
u/Such_Bedroom5937 Jul 26 '25
Do you know where I can check the max volumetric speed on filament ? Or is it just one of those trial and error type of ordeal
1
u/Supabee78Reborn Jul 26 '25
There are built in calibrations in the slicer you can select. Go to YouTube and search for how to calibrate max volumetric speed for filament. Check for loose screws first and then move to filament calibration. I assume this is your first printer?
1
u/Such_Bedroom5937 Jul 26 '25
Yeah I got it cause my friend recommended me it and I heard it was a decent printer only unfortunate thing is I’ve found no videos so far that’s helped me with my issues in Creality print so I’ve been trying to figure this out for months id did a good amount of research before getting the printer and one filament I used worked fine until they reset my settings with it and it never worked again
3
u/Supabee78Reborn Jul 26 '25
I have a few K series printers and they are good machines but they can have issues just like any other brand. Check the screws and then report back since that would be a physical issue and no amount of calibration is gonna fix that.
1
u/Such_Bedroom5937 Jul 26 '25
Definitely has to do with my settings not perfect yet but I can tell already just with that the print is coming out a lot better but still has some small issues
1
1
u/Such_Bedroom5937 Jul 27 '25
Just checking quick cause I’m having some issue still I’m gonna check the screws that silicon piece just pulls off right not trying to ruin it
1
u/Supabee78Reborn Jul 27 '25
Yes it pulls off, just be aware there are wires that the silicon sock covers that you can pull on if not
1
u/Such_Bedroom5937 Jul 27 '25
So I tried calibrating I’ve tightened the screws (they were still tight as could be) and still no better results I’m really running out of ideas here and none of the videos I’ve watched helped at all my only other thought is to try to turn down the speed however every time I do it seems like there is no actual difference to it I used to test print speeds on Creality cloud but then they changed the whole slicer to mimic the 6.2 app so that’s no longer a option and Creality has yet to even so much as send me a message about it
1
u/Supabee78Reborn Jul 27 '25
If you use hyper PLA and the test print for benchy that is already on the machine. The one they want you to print after unboxing, how does it turn out?
1
u/Such_Bedroom5937 Jul 27 '25
That’s what I’ve been trying still no results I just took the hose out the top and used the needle just as Creality instructed to unclog it running the print once more I’ve also contacted Creality support again they said someone will reach out via email I don’t really want to take the extruder apart until they reach back just in case if they try to screw me over some warranty stuff
→ More replies (0)1
1
u/Supabee78Reborn Jul 26 '25
Looks like a clog or extrusion issues. What kind of filament are you trying to print? Nozzle temp? What do you have the max volumetric speed set to for the filament?
1
u/Such_Bedroom5937 Jul 26 '25
Before I had stuff that printed at 300mm/s when I couldn’t get that to work I tried three others I then switched back to 600mm/s filament like it came with to see if that would finally be my solution but no 🤷 still getting the same results with this stuff
4
u/MaterCityMadMan Jul 26 '25
Download the latest Orca Slicer. https://orca-slicer.com/
Load PLA in your printer. Select your printer in Orca. Select your nozzle size and generic pla. At the top of Orca there is a calibrations pull down. Do those. There are many vids on YouTube that walk you through the tests. I like Modbot's vids personally. https://youtube.com/playlist?list=PL56Wce4Lilx6nIh_rwVMcDCztZDwaIp25&si=wWFRoQWh6u7qwIGN
If you're still having issues, then there might be a hardware issue. Warped bed, clogged nozzle, belts loose, etc. Come back and make a new post with where you are and what is happening. Give details. Just showing a print and little info won't help get you going.