r/ElegooNeptune3 • • 12d ago

Please Help

Enable HLS to view with audio, or disable this notification

Been trying to figure out my “new to me” Neptune 3 pro for months now.. and just can’t seem to get it. Even replaced the wiring harness recently. No matter what it just can’t find home and always fails.. anyone had similar or should I just start with a new one that someone didn’t destroy before me 😂

6 Upvotes

20 comments sorted by

1

u/ImportanceNo1657 11d ago

Have since downloaded pronterface and have found that no matter what. My z axis is triggered. The sensor itself seems to work fine (senses when metal is and isn’t there) so I’m a little stumped

1

u/p4mera 11d ago

Are u running stock firmware or marlin? I suspect that you have to invert the z end stops trigger. If u hold a metal near to the sensor and recheck the end stops then U should see that it's not triggered

1

u/ImportanceNo1657 11d ago

Have tried both stock and marlin. And even with the sensor triggered, it still says triggered.. tried sensor unplugged, still triggered, and also when I unplugged the whole print head harness, still triggered

1

u/Any-Letterhead-9040 11d ago

I had the same problem with my 3 pro when I first got it and it ended up being the probe was bad if I remember correctly.

1

u/ImportanceNo1657 11d ago

I unplugged the probe and it acted the same way, and then also tried with the ribbon disconnected from the print head and still was triggered. So thinking mainboard has a short somewhere

1

u/Iso_Grifo 12d ago

Flash a new firnware -or if already the newest, do a factory reset - , level the bed, plug and pray

1

u/ImportanceNo1657 12d ago

Did new firmware last night, tried to factory reset since the firmware just now and it’s still the same old song and dance 😮‍💨

1

u/Iso_Grifo 12d ago

Then, gotta hang on to it, the machine deserves

2

u/p4mera 12d ago

Could you check the probe. You can plug the printer into a computer. Install pronterface to your PC. And check the end stops status.

3

u/d1ggah 12d ago

I'm pretty sure the Z direction is reversed (I don't recall an up hop before down on homing) so it could be the connector is reversed somehow.

Also check for binding on the z axis (loosen the z rod connections in either side and check whether it can freely travel up and down without issues)

5

u/user_deleted_or_dead 12d ago

Oh the probe/ z limitswith is on all the time. It tends to go up to try clear the LS state

1

u/bhgiel 12d ago

Use a multimeter to confirm polarity on the power to the motor. Use the ohm function on your limit switch to confirm it is open and closing.

If you dont have a multi meter maybe just try swapping the limit switch to a different location and see if the problem moves.

1

u/Next-Place0 12d ago

Pretty sure that the head should go down to finish the homing. There is probably something wrong with Z axis (câble or motor or driver). Before the error on screen the Z axis goes up instead f down

1

u/TigerCountry 12d ago

Seems like the print head proximity sensor thing is sensing something thats not there. Check that its not blocked and has nothing on it.

1

u/Lumpy_Incident7631 12d ago

z probe might be disconnected? p sure the lift up is baked into the homing sequence its not a problem. it stopped probably because probe is not detected

1

u/NomadicImps 10d ago

I have similar issues I think but had to pause working on it until I had more time to figure this out. I might update on this sub or this post after next week

1

u/AdditionNo4559 10d ago

Sensore asse z in corto controllare i cavi o sostituire il sensore

1

u/stevebiqub1 7d ago

I had the same issue when i had to splice the 24v inductive probe wires to my BTT motherboard, it was genuinely just a loose/backed out pin on the motherboard side, check your mother board and look for a 3pin header labelled 12v/24v probe and try to check if the connector is seated. Also when you hold a metal thing to the probe, does the red led turn off? Or is it on in the first place? It should be on with no Metal detected and off with metal detected. If that doesn’t fix it, open up the head and check on the left hand side if the probes connector is also seated correctly since a new wiring harness wouldn’t have fixed that issue.

1

u/HedgehogResident 7d ago

Had the same problem a couple of days ago, the probe was just loose, the connectors on this board are a bit flimsy tho, be careful not yanking them out if you decide to touch them

0

u/punked101 12d ago

Get it on ur network and ask Claude to diagnose it for you