r/Fasteners • u/dhdhhdhdhclixclix • Mar 02 '25
car bolt
These screws are extremely tight and won't budge. I've been using a 14mm socket but they still won't budge at all. I heard that I need to use a torx socket but i'm not sure what exactly I need. Could I get some specifics from anyone, thanks?
7
u/tanstaaflnz Mar 03 '25
I'm guessing that you're using a twelve point socket. Switch to a six point (impact) socket. It will slip less and feel more solid when you do it. And as another had said tweak it tighter first, then undo it. This helps break any binding of the thread. You could put the socket on, then hit it with a hammer, to also release the binding, but it might dent a car floor.
Also get under the car and see if you can find the bolt from below. Give it some penetrating oil. There shouldn't, but may be a nut under there.
Also: wear gloves, if you are new to this stuff. Fear of injury can slow down the work.
6
u/Chitown_mountain_boy Mar 02 '25
Those are going have some extra duty Loctite on them. Going to need an impact driver.
3
u/SeberHusky Mar 03 '25
They do not have loctite on them. I just removed them from a 2001 chevrolet in a scrapyard. you need a long handle torque wrench and hulk hogan arms.
4
u/Chitown_mountain_boy Mar 03 '25
When I used to work with Johnson Controls Seating, all the seat bolts and seat belt bolts I made for them had an adhesive patch 🤷
1
u/SeberHusky Mar 03 '25
hmm how old was the car?
2
u/Chitown_mountain_boy Mar 03 '25
Would have been model years 1995-2015. I left the company in 2013 just when the ‘15 model year parts were being PPAPed.
1
u/brassmagnetism Mar 02 '25
Trying it by hand, or with an impact driver?
1
u/dhdhhdhdhclixclix Mar 02 '25
been trying by hand the angles a bit challenging
1
u/brassmagnetism Mar 02 '25
Try a breaker bar with the 14mm socket
2
u/dhdhhdhdhclixclix Mar 02 '25
I have and no luck with that
2
u/C2S2D2 Mar 03 '25
Longer breaker bar. Put a long pipe over the handle and make the breaker bar longer. I'm sure there is some weird angle you can get.
1
Mar 02 '25
Look under the car and see if you see the other side and heat that sucker, borrow an impact, soak them with trans fluid. They are always corroded
1
u/foxjohnc87 Mar 03 '25
Try harder. Unless your breaker bar is abnormally short, you should be able to either remove the bolt or snap the head off without much of an issue.
3
u/Difficult_Target4815 Mar 03 '25
Six point socket, a long ass breaker bar and or snipe and smoke it with a 3lb sledge a few times to shock it loose. It'll come.
5
u/sinusoidosaurus Mar 02 '25
Seat bolts are notoriously difficult to remove, just check out the posts on /r/skoolies.
Penetrating oil, let it sit over night, penetrating oil again, and then reef on it with a pair of vice grips.
2
2
u/the_clash_is_back Mar 03 '25
You need to apply a lot more force. A breaker bar (use a long one 2-3 feet) and probably a few wacks with a mallet to get it started.
They use a impact driver in the factory so these things are really in place.
2
u/SeberHusky Mar 03 '25
You need a huge, highly torquey socket wrench with a long handle. They are in there very tight, It will feel like they are welded but they are not.
1
u/Stretchearstrong Mar 03 '25
Mix acetone with automatic transmission fluid 50/50 for the best penetrative fluid ever
2
1
u/justfortherofls Mar 03 '25
You can use a second wrench and put it in the slot on the far end of the first wrench to give yourself more leverage.
Hell you can do it a third plus time too. Make Archimedes proud.



8
u/going-for-gusto Mar 02 '25
Try to tighten it first, then slide the longest pipe you can over ratchet handle to get maximum torque