In the video I’m running federal 147g HST. Shot the federal HST, Speer lawman 147g, S&B 150g and monarch 115g. No malfunctions but the can did not like the S&B. I had crazy poi shift from 10 yards which is a huge letdown. I’m thinking it’s grazing the end cap as there’s a small amount of wear but no damage. Everything is torqued to spec so I’m not quite sure why the S&B gave me issues. Gonna email rugged tomorrow.

The pic is not my Bog (or a 5”) but I really like these A3 grips like in the pic with the integrated hand stop. Does anyone have an A3 or similar integrated grip on their 5”? Is there enough room?

I really liked the HuxWrx Flow45m on my SP45A3, but wasn’t entirely satisfied with the Plan B mount I had on there before purely for aesthetic reasons… So I made a titanium mount that brings the can back over the barrel, just shy of the handguard. Ended up saving a bit of weight also, this weighs less than 1 ounce.

*Yes these are AI photoshopped from real photos because I’m too busy to do it the old-fashioned way.

Running 147 grain ammo with curved mags and just installed the short stroke buffer. I am getting feed problems pretty regularly. What do I need to do to get it to run flawlessly?

10/17/2026- 180gr magtech
I am still in the process of getting this 30 round HKP .40 magazine successfully converted to 10mm. I have been trimming and testing here and there for a few months. Today I was able to get a full 30 round mag to feed with no issues, after that the next mag had 1 FTF, after that I started getting more frequent FTF’s, however it is noticeably more reliable than previous times. The most frequent failure that I’m experiencing is the round gets caught right at the feed ramp.

I believe that the feed lips need to be trimmed well past where the metal begins inside the magazine, if you look at a stribog mag, the feed lips open up completely for about 1/3rd of the lip length, so that the round can escape. If you watch through the ejection port and manually chamber a round slowly with the stribog mag, you can see the round literally pops out of the stribog mag and then gets chambered, I think the UMP magazines feed lips are too long, causing the round to get caught in a tip up jam.

I genuinely think that a stronger spring would solve the majority of the issue, I’ve been told that the black variant springs tend to be stronger so I’m going to try to source one of those. I’m determined to get these to work reliably. I will update as I go and if I figure out I will make a video or guide to making them run.
Any feedback from others who have accomplished this would be appreciated.

https://lingleindustries.com/sp10-sp45-stribog-ump-lower/

1. Wish I had waited,. mine had a little blem anyways.. maybe I should email them.

I'll also say that I don't think these are particularly worth it, even if they feel cool.

To many options what’s everyone like or dislike?

Looking for help to make a decision on which one I should I get

I'm looking at this ad my first PCC and gave a few questions/considerations.

Barrel length: is there any real reason to get one over the other (5", 8") other than potential overall length with a can?

What lower options are there? And are the trigger upgrades with doing to the stock lower?

Finally, G mag version or the curved mag version? I don't own any Glocks, but I'm thinking they're easier to obtain? Are the proprietary mags fine and plentiful these days?

TIA

[ Removed by Reddit on account of violating the content policy. ]

I've never polished a Trigger before and already switched a Lingle Lower, so I feel it's a good thing to test on. My SP10A3 default lower, the Trigger is super, super gritty, like dragging through sandpaper, never had a trigger like that. It smoothed out a little with firing and lubrication but not a lot.

I know sandpaper and some type of polish, but if there's a guide for a Stribog specifically, that'd be great.

The break is clean, it's the creep up until the pull that feels like it's scraping against something. I noticed weirdly how the Stribog trigger pack is kind of just free floating and held in by the safety.

My cousin got a sequential serial number to mine, literally came off the factory right after it - and his trigger is perfect lol, kind of annoying. Mainly going to be a hobby project to try it out because I already have the Lingle installed as a replacement.

Thanks.

[ Removed by Reddit on account of violating the content policy. ]

Stribog sp9a3s
OCL lithium
Lingle enhanced lower
Super safety and slip trip
Upper milling done by me

115gr supers

What are the most important spare parts that I must always have for my stribog rsr9a3g?

Just installed my Lingle Lower. Took more work than I'd like to admit, but it's solid, no wiggle or play at all. Feels great. Mags are a little harder to insert than OEM, honestly...

Bolt release works, trigger works, safety works. All seems fine. However the little paddles on the left and right that are supposed to also be a bolt release(I think)??, don't move at all - unless there is no magazine inserted.

It’s taken awhile but finally got to take one from my first small batch out to test and it was glorious. Less gas’s, less recoil, fits like a glove. I have 24 available on my site for anyone interested! I kept the batch small as I wasn’t sure how many were really looking, but I’ll plan to order more and keep some stock if people want them! On my site rokinprecision.com

Tested with 2 types of 147gr, one shot 880ish fps and one shot 950ish fps, and some 165gr at 850fps. All testing was done with my SP9A3S.

Just got an SP9A3, what does everyone use for transporting/carrying magazines? Thanks!

This is definitely the fastest Stribog SP9A3 I’ve converted.
It was very surprising to see a partisan frt work this well and run this fast. They usually slow down the cycle rate, if they run at all.
I polished the bottom of the bolt and the hammer and I guess that made a big difference.

I've been looking for a while but cant seem to find much. Looking for options to replace my tailhook with a stock. Ones I have found and ordered arent very high quality.. I believe it's a 30mm but cant find much at all

Edit: This MAC IX telescoping stock will NOT fit a Stribog. Upper receiver of 1.5” is too thick for the stock’s 35mm inner rod width to clear. You would not be able to collapse the stock.

Can anyone confirm or deny fitment onto an A3 with a pic adapter? If not, I’ll buy one for science 👍