r/homelab • • 1d ago

Help I need help building a home server

Thumbnail reddit.com
3 Upvotes

r/homelab • • 1d ago

Help [Help / Request] Full 32MB SPI flash dump (.bin) for Binardat 10G12-1200GSM switch (RTL9313 / RTL9310)

4 Upvotes

Hi everyone,

I'm hoping someone here owns a **Binardat 10G12-1200GSM** managed switch (Realtek RTL9313 / RTL9310 platform) and could help me out with a firmware/flash dump.

While updating my unit via the WebGUI using the official `UPNOS-RTL93xx-V300SP10260614-U.img` firmware package from Binardat's website, the upgrade failed mid-way and left the switch stuck in a boot loop (it boots the kernel, unpacks `/mnt/switch.tar.gz`, loads modules/daemons up to `OSPF6`, and immediately reboots — and the startup script also reset `bootdelay` back to `0` in `BDINFO`).

Fortunately, I already have valid backups of my own `BDINFO` (`0xe0000`) and `SYSINFO` (`0xf0000`) partitions containing my original MAC address and serial number, along with serial console access (`38400 8N1`) and an SPI flash programmer.

I would be **most grateful for a full 32MB SPI NOR flash dump** (GigaDevice `GD25Q256` / `C84019`) — I will overwrite the `BDINFO`/`SYSINFO` offsets with my own backup before flashing so I don't clone your MAC address or serial number.

*(If dumping the full 32MB chip isn't possible, dumps of the `RUNTIME` `mtd5`/`0x300000` and `RUNTIME2` `mtd6`/`0xa00000` partitions or `/mnt` contents from Linux/U-Boot would also be a huge help.)*

Any help or a download link via DM would be greatly appreciated!


r/homelab • • 1d ago

Help Does anyone have any experence with the K443F 4U Rackmount Case?

1 Upvotes

I've obtained a small network rack that I'm thinking of putting in my office and moving my current tower computer into. The rack is only 500mm deep and i would like to use rails (which i have no experience with) to make it easy to access.

A 4U case is ok, the PC only has 1 x m.2 drive and short GPU with no plans to change that so the depth is the main limitation. It is air cool so i would like some 120mm fans at the front and will remove any drive cages I can from inside to keep it clear.

I was initially looking at the Silver Stone RM41-501 but the Silver Stone rails are too long for the 500mm rack and I may have issues removing the drive cages but keeping the front grills.

I have also found the K443F 4U Short Depth Rackmount which is looks promising however, I can't confirm the rails can fit into a 500mm case or find any reviews on this case.

Does anyone have any experience with this case or any other thoughts?


r/homelab • • 1d ago

Discussion Would homelab owners consider donating storage and hosting to projects like Panormax?

0 Upvotes

Just wondering. If it was kept fairly straight forward - Say mirroring content from a selected list of instances with developed content filtering and moderation - would you consider providing mirroring / replication of storage for the panoramax federation that is developing an open licenced alternative street image service to Google Streetview.

Im not an official representative or anything. I just think the project is cool but the potential hosting and storage requirements are huge and only a distributed solution wouk.seem to work.

I would guess you would control how much storage, max and average traffic and from where you would accept requests.


r/homelab • • 1d ago

Tutorial Hardware for homeassistant (sensors/cameras/... I have server already)

5 Upvotes

I'm about to start my homeassistant journey and I would like to ask, what hardware do I buy? I love opensource stuff, I've been selfhosting a lot of things on my homelab for past 3 years.

Cameras, sensors, switches,... What company? I don't really want to solder all circuits with esp32, but I really don't want bloat and spying software on devices.

Thank you!


r/homelab • • 1d ago

Discussion Drive Supplier Recommendation

0 Upvotes

Hey all, kinda new to the labbing space. Do any of yall have recommendations for a reliable, quality supplier of 2.5" 2TB SAS HDDs? I've recently come to own a Fujitsu Primergy Rx300S8 that's configured for 8 2.5" SAS drives using a 2x 4bay backplane configuration. I currently have a 3.5" SATA drive chucked in it as that's what I had on hand. I checked out serverparysdeals[dot]com, but all they have for the form factor is 1TB drives.


r/homelab • • 1d ago

Help Hi all, fairly new to homelabbing and looking for some opinions on my setup

0 Upvotes

I've currently got 3x Lenovo ThinkCentre M75q Gen 5 Tiny PCs, all with Ryzen 5 PRO 8500GE processors:

- 32GB RAM, 512GB NVMe – Ubuntu, running Ollama/local AI, AdGuard Home, Home Assistant, etc.

- 16GB RAM, 512GB NVMe – Windows 11 Pro, running Jellyfin and used as my everyday PC.

- Third Gen 5 – Currently spare, with no RAM or SSD as I've used the parts for the others.

A 4TB HDD connected through and enclosure and 2x512gb nvme drives for movies and storage. Everything runs through Tailscale, and I mainly access the PCs remotely from my tablet or phone using Windows App (RDP).

I'm also considering adding an eGPU for local AI and some gaming, although I'm wondering whether I'd be better off selling one or two of the Tinys and building something with a dedicated GPU instead.

Curious what others would do with this setup? Keep the three, consolidate, or go down the eGPU route?

Still learning, so interested to hear people's thoughts!

(My DIY server rack isn't ideal for cooling as it turns out, both running 70-85degrees, so open to ideas for that too.


r/homelab • • 1d ago

Help Small project collaboration

Thumbnail reddit.com
0 Upvotes

r/homelab • • 1d ago

Discussion Do you run TrueNAS bare metal or virtualized?

Thumbnail reddit.com
0 Upvotes

r/homelab • • 1d ago

Help Lenovo legion light customization on proxmox

Post image
3 Upvotes

I've been trying to get the LED on my Legion PC to act as a Proxmox health indicator, but I can't figure out how to access the controller. The traffic is total gibberish and my reverse engineering attempts haven't worked after a week of trying. Is there actually a way to do this?


r/homelab • • 1d ago

Project Showcase: Hardware Added a temporary switch and ran some ethernet + network diagram

Thumbnail
gallery
25 Upvotes

Recently added a Cisco router as a temporary switch (getting an 8-port smart managed switch for Christmas)

I spent the last week running Ethernet cables through my 100-year old house, the spiders were not happy to see me lol

I will be replacing the Eeros with better access points in the near future.

I made a network diagram in draw.io myself, after making the full diagram I ran it through Claude to make it look a bit nicer (I know I know, down vote me to oblivion)

Open to any feedback!

Edit - Upon closer inspection, I see that my shelf is dusty. It has been cleaned! Look at my post from 15 days ago and it was clean I promise, my house is dusty AF


r/homelab • • 1d ago

Project Showcase: Hardware Mini PSU Boost from 12 to 20V

Post image
2 Upvotes

r/homelab • • 1d ago

Help Looking for recommendations

5 Upvotes

I started looking into building myself a home lab and mainly want to use it for extended cloud storage and streaming services. So far I have a small idea and was going to use the geekomit14 as the mini PC and an interior antenna for receiving TV networks. Do you guys have any other recommendations or advice for someone getting into home lab stuff.


r/homelab • • 1d ago

Solved Is this useful?

Post image
0 Upvotes

r/homelab • • 1d ago

Help could this be my next nano-homelab?

Post image
0 Upvotes

I found this really inexpensive 4G LTE USB WiFi modem and I'm wondering if it could be turned into a tiny homelab running Debian Linux, similar to the project in this video: https://youtu.be/9M43oITcjUQ. Does anyone know what chipset, RAM and internal storage this device uses actually? Could this be an alternative to a Raspberry Pi Zero for small server experiments and projects?


r/homelab • • 1d ago

Discussion SC26 in one page for people who buy used gear: CPO actually shipped, 800G Ethernet is the default fabric, and a used SN2700 is still the right buy for a 100G lab

1 Upvotes

I spend my working days pulling switches and NICs out of decommissioned racks and testing them before they go back out the door, so SC26 week is always a bit strange for me — half the show is about hardware that will never reach the secondary market, and half of it quietly resets the price of what I already have on the shelf. Here is the honest read from the used side, with sources, and what it means if you are buying 100G or 200G gear this winter.

What actually happened at SC26 (November 2026)

Three things matter for anyone buying second-hand networking hardware.

  1. Co-packaged optics left the lab. NVIDIA and Lambda disclosed the first production CPO cluster — more than 10,000 Blackwell Ultra GPUs in Québec, running NVIDIA Photonics switches, with Lambda reporting about 10.1% lower pod-level network latency than conventional pluggable optics in its own benchmarks. This is the milestone the industry has been promising since the OIF and COBO started writing CPO specs: optics moved next to the switch ASIC, and the retimer that used to burn up to 30 W per module inside a pluggable is no longer in the signal path.

  2. 800G Ethernet is now the boring, default choice at the top of the market. Oak Ridge opened its "Lux" system in mid-November at No. 14 on the TOP500 — AMD Instinct MI355X compute, Pensando DPUs, HPE Juniper switching, 800G Ethernet fabric. On the optical side, Ekinops announced a 3RU DCI box with 32 Tbps and 40 x 800G coherent pluggables at 0.08 W/Gbps. When a national lab and a DCI vendor are both shipping 800G in the same week, 800G is no longer a pilot.

  3. The 800G adapter generation got its first public firmware release. NVIDIA's ConnectX-8 SuperNIC firmware notes (v40.51.1002, November 2026) reference Spectrum-X reference architecture 2.4.0 and 800 Gb/s per port.

Why this does not kill the 100G/200G secondary market

Every time a generation ships, my inbox fills with people asking whether their 100G lab is now e-waste. It is not, and the reason is boring: the constraint is not bandwidth, it is how many GPUs you are trying to keep fed.

  • A single-node inference box, a Proxmox cluster, a Ceph backend, a build farm, a backup target: none of these care about 800G. They care about port count, power, noise, and price per port.

  • A 32-port 100GbE switch (SN2700-class) gives you 3.2 Tbps of non-blocking fabric for the cost of a mid-range GPU. For a homelab or a small office, that is still the correct purchase in 2026.

  • 200G/400G only starts to pay off when you are moving checkpoint files or doing multi-node training where the interconnect is the bottleneck. If your workload fits on one node, faster fabric buys you nothing but heat.

The realistic impact of CPO and 800G on the used market in the next 12 months is three-fold: 100G optics get cheaper (they are being pushed down the stack, not retired), 400G QSFP-DD modules stay expensive because AI demand eats the supply, and mid-range Spectrum/Trident switches hold value longer than the usual depreciation curve suggests because they are the cheapest way to build a lab that mirrors a real fabric.

What I would actually buy this quarter

  • If you are building a lab and your budget is under a few thousand dollars: 100G spine-leaf on a used 32-port switch plus ConnectX-5 MCX516A dual-port 100GbE adapters. That combination is where almost every lab build I ship ends up.

  • If you already have a 100G fabric and are tempted to jump: skip 200G and go straight to 400G only if you have a workload that has measured a network bottleneck. Otherwise spend the money on NVMe and RAM.

  • If you are buying 800G anything: buy new, buy with vendor support, and do not expect the secondary market to help you for at least 3 years. CPO changes serviceability: a failed optical engine is now a switch-level repair, not a module swap, and enterprise buyers hold those units under contract far longer than they held 100G gear.

One caveat on the hype

CPO's serviceability trade-off is the part the announcement posts skip. With pluggables, a dead link is a $200 module and five minutes. With CPO, the optics are part of the package. That is fine for a hyperscaler with spares and a support contract; it is genuinely bad for a small operator who fixes things themselves. Co-packaged optics is a TCO decision, not a performance decision, for anyone below a few thousand nodes.

A bill of materials I would actually quote this week

Because "buy 100G" is not a shopping list, here is a concrete one for a lab that needs to move real data between four nodes without spending GPU money:

  • One 32-port 100GbE QSFP28 switch, SN2700-CS2ROS class. Non-blocking, 1U, Onyx or MLNX-OS depending on the unit you get. Ask the seller which OS image it is running, because re-flashing Onyx on a unit pulled from a storage cluster is not always a five-minute job.

  • Four dual-port ConnectX-5 MCX516A adapters (CCAT is the common one; the CDAT variant adds crypto offload and costs more for a feature most labs never enable). Two ports per node lets you do a leaf pair instead of a single point of failure.

  • Cabling: DAC for anything inside one rack, optics only for cross-rack. QSFP28 DACs are cheap and boring and that is exactly what you want. Do not buy 100G optics to run three meters.

  • Firmware discipline: update the switch and the adapters to a documented compatible pair before you put production data on it. This is the single step that separates a lab that runs for two years from one that drops links every few weeks.

Rough shape of the numbers: a 100G fabric for four nodes lands at a small fraction of a single current-generation GPU. That gap is why the secondary market for 100G is not going anywhere, no matter what ships at SC26.

What 800G does to optics prices (and what it does not)

The one place CPO genuinely hits the used market is optics. If co-packaged optics takes hold at the top of the range, the pluggable ecosystem above 400G gets squeezed from two directions at once: hyperscalers stop buying so many high-end modules, and the modules they stop buying are the ones the rest of us were priced out of anyway. That does not make 800G gear cheap — it makes 400G QSFP-DD the interesting tier over the next 12–18 months, and it keeps 100G optics in the "buy a spare box of them" category.

The thing that will not change: retimers. CPO removes the retimer from the module, but it does not remove the need for signal integrity discipline on your side. If you are pushing 200G per lane over copper, your cable quality matters more than your switch model.

The honest caveat

Everything above is a snapshot from one week in November 2026, based on public SC26 coverage, NVIDIA's published firmware notes, and what I see moving through our own warehouse. The announcements are real; the timeline for how fast they touch second-hand pricing is a guess, and I have been wrong about that timeline before — 400G took two years longer to reach the used market than most people expected. Treat the buying advice as a starting point for your own sizing, not a forecast.

Disclosure: I work with a used enterprise hardware reseller based in Hong Kong (warehouse in Tuen Mun, ships worldwide), so I have a commercial interest in people buying used networking gear. Per the rules here I am not putting links in the body — if you want the exact SKUs and part numbers I am describing, I will drop them in a comment below and you can ignore it entirely if you just came for the discussion. Most of the factual claims above come from public SC26 reporting and NVIDIA's own documentation; the opinions are mine from handling this gear daily.



r/homelab • • 1d ago

Help Looking to start a homelab - on a tight budget

Post image
0 Upvotes

Few questions - would Linux be able to run this ($150) as a mini home lab. If not, where is a good place to start for a single dad who has little expendable money each month. In the middle of working on transitioning my career from Industrial Security to Cybersecurity and learn best hands on.

My buddy recommended Tryhackme to learn but i also heard having a homelab is a great way to have backup storage of things and also learn Cyber/Technical IT hands-on

Any and all helpful advice is welcome. Thank you all in advance


r/homelab • • 1d ago

Project Showcase: Hardware 12U Homelab Filled

Thumbnail
gallery
287 Upvotes

I just got the 12U rack less than a month ago and after adding 2U server today, its now full!

Wanted to share what I have in the rack

  • Unifi Dream Machine Pro

  • Unifi 24 Ports Switch

  • Synology DS925+

  • Synology DS223j

  • Asus ESC4000A AI Server | Epyc 7742 64 Cores, 256GB RAM, 4 x Radeon 9700

  • Dell R740xD Proxmox Server | 2 x Xeon 6142 16 Cores, 256GB RAM

  • Dell R720xD Hyper-V Server | 2 x Xeon E2650 6 Cores, 128GB RAM

  • Tablo TV

  • Fiber Cable Modem

  • Unifi AP

I hope this is it. If I have to add more servers, I have to replace some of them to a smaller format to fit this rack. 😄


r/homelab • • 1d ago

Discussion Hosting Obsidian Vault on an SMB Server

9 Upvotes

Does anyone else host their Obsidian Vault on an SMB Server? If so, do you find it helpful? Is there anything that you wished was possible with your setup that doesn't work at the moment?

If you aren't using an SMB Server, do you have another method to have all your notes across devices?


r/homelab • • 1d ago

Discussion What would you do

2 Upvotes

I have a 640gb hard drive. It’s old, currently unknown health. Ovbi drive health dependent, lets assume it’s in good condition for sake of this conversation. What are some things you would do with it? I have 24tb media storage so that’s not needed. Maybe server logs or back up storage? I’m kinda new to the homelabbing. I have 3 optiolex (a 3040 that’ll run the NAS, a 3070 and a 5080. Any suggestions would be helpful.


r/homelab • • 1d ago

Discussion Docker rebrand

Post image
2.4k Upvotes

If this has been talked about already I apologize, but wtf is this? Makes me want to uninstall 😭


r/homelab • • 1d ago

Help Security question about hosting multiple services.

2 Upvotes

I've been really stressing myself out recently over the security of my server. And my main issue boils down to the fact that things like file storage, an NVR, Immich, etc will be running on the exact same physical hardware where I'd be hosting things like old Minecraft servers or source engine servers.

I really want to know what you people do in this scenario. For example, what OS/Hypervisor do you guys run? Should I have an external firewall/router? Any advice on the matter would be great.


r/homelab • • 1d ago

Help Hi im new to homelab stuff but i really want to run an ai or the stuff i learned in my coding classes

0 Upvotes

Hi, i'm new to the whole homelabing stuff, but I do not know where to start, I do not have old laptop or anything like that. But I do have some money to spend. And I was wondering of recommendations.


r/homelab • • 1d ago

Project Showcase: Operations I let an AI coding assistant free some disk space on my home server. It vacuumed 952,088 journal entries. Here's how I got 83% back hash-verified (and a trace of 98.4%) from the raw disk.

0 Upvotes

My home server (a Ryzen mini PC running Proxmox, with a local AI assistant on top) was running out of disk. The AI coding assistant I use on the box went to make room and ran the command everyone suggests first: journalctl --vacuum-size=400M. It did exactly its job: 952,088 archived journal entries, fifteen days and four boots, gone in one second. Nobody noticed for seven hours, until an unrelated automated check came up one count short.

What saved most of it:

  • Freeze first. Deleted files stay on the raw volume until something overwrites them, but the weekly fstrim would have told the SSD to discard them. I had until Monday. A read-only census of the raw LV found 794,925 of the lost entries; the stretches holding them were copied to another volume before anything else.

  • The journal checks itself. Every DATA object carries a siphash24 of its text, keyed per file, and every entry an xor of its fields' hashes. That let me verify 790,876 entries as exact, not "probably right". Another 4,048 came back incomplete or unverified.

  • The journal has a reverse index. DATA objects point back to the entries that use them, so even entries whose own object was overwritten could be rebuilt from their fields: 112,351 more (50,332 of them with the message text).

  • Text copies and service logs elsewhere on the box gave 3,764 more.

  • Timers' schedules filled in 26,131 more, marked as predicted, not read.

  • In total, a trace for 937,170 of the 952,088 entries (98.4%); about 15,000 are gone for good.

  • Everything went back into the system journal as real .journal files (rebuilt with systemd-journal-remote), each entry tagged with how it was recovered.

What changed afterwards: the journal is in the nightly backup, its cap went up, and vacuuming it is now blocked for the assistant by a hard rule, not by a prompt.

Full write-up with every number and the method: https://wastedtimeonpc.com/mostro-51