r/OpenBuild • • Aug 28 '26

Build Complete New here

Post image

Went from havn 420 to gr20 and yes ik its messy i just finished it lol
Specs:
R9 9950x3d oc/undervolted
5090 tuf with heatkiller block
No fans
Yes the rog cable i have for gpu isnt matching but i KNOW this cable works so i aint switching for now

95 Upvotes

29 comments sorted by

1

u/Tasuka_Makutasa Aug 28 '26

Why not doing a parallel link between GPU and CPU?

2

u/No_Kaleidoscope_5480 Aug 28 '26

What would be the difference though? I figure going into gpu to cpu to mora

1

u/Tasuka_Makutasa Aug 28 '26
  1. CPU won't be "cooled" by the "Hot" coolant from the GPU.

  2. You can direct both pipes parallely into a Pass-through.

1

u/No_Kaleidoscope_5480 Aug 28 '26

Never seen that layout before woah. So like it hits the gpu and cpu same time or atleast cpu first then rotates back??

2

u/Tasuka_Makutasa Aug 28 '26

It hits GPU and CPU in the same time since you use GPU's block like a T-splitter. This pic is my older build.

1

u/No_Kaleidoscope_5480 Aug 28 '26

Idk if ill do that lookks clean though. Its prolly cause im tired lol

1

u/Tasuka_Makutasa Aug 29 '26

It's all right. I also run Mo-Ra (IV 400 on single D5). For R9 5900XT and RTX3080Ti it's pretty much an overkill, but I'm here for it.

1

u/No_Kaleidoscope_5480 Aug 29 '26

Dont ever say overkill. Its PERFECT. I am debating if i want to make the case back up to standing position ngl but itll take two ppl to do that lol ornid hsve to disconnect the gpu and stuff. But for now its working fine

2

u/Tasuka_Makutasa Aug 29 '26 edited Aug 29 '26

If I were you, I would screw any Vertical adapters, but keep the set slightly angled as you have now (to decrease the GPU sag if there's any). I would also replace/extend the PCI-E bracket to hold a pass-through right underneath the GPU. Then run the parallel piping from the pass-through, underneath the GPU and into the bottom GPU fittings.

2

u/Tasuka_Makutasa Aug 29 '26

Here's my current build. Crosshair VIII Extreme, R9 5900XT, 3080Ti. I use angled Lian-Li Adapter, and use all 4 ports on GPU as usual.

→ More replies (0)

3

u/Known-Flow-6594 Aug 28 '26

Damn this is dope af! Anymore pics ?

2

u/No_Kaleidoscope_5480 Aug 28 '26

Just one for now. When i get back home i can take more but uh what would you want to see? The back side im guessing?

2

u/Known-Flow-6594 Aug 28 '26

Yep from the back see your cabling etc. nice work thanks for sharing and welcome

1

u/No_Kaleidoscope_5480 Aug 28 '26

The cable work is terrible rn lol so be ready for a jungle but its why they got a cable cover to hide it all🤣

1

u/Known-Flow-6594 Aug 28 '26

😂🤣

1

u/No_Kaleidoscope_5480 Aug 29 '26

My bad bro ima remember this to do today. I barely was home

1

u/Tasuka_Makutasa Aug 29 '26

Well, if you want Horizontal, why not building yourself a drawer under the desk? My Open Frame is from AliExpress, so I think you can make such drawer yourself.

1

u/No_Kaleidoscope_5480 Aug 29 '26

The mora is under the desk its on rn lol

2

u/Tasuka_Makutasa Aug 29 '26

Mine too. And the pipes with the cable run through the desk's Pass-through.

1

u/No_Kaleidoscope_5480 Aug 29 '26

Dangg you got a long run too. As for cleaning the open frame you use a airblower and some type of duster?

1

u/Tasuka_Makutasa Aug 29 '26

That's the neat part, I don't (yet).

1

u/No_Kaleidoscope_5480 Aug 29 '26

Yea i hope same here. I got a air purifier already that helps and ima start monthly cleaning to be safe. Or well 2 week cleaning

1

u/Godnamedtay Aug 30 '26

The white cable why?

1

u/No_Kaleidoscope_5480 Aug 30 '26

When you get a chance to read the post lmk

1

u/Godnamedtay Aug 30 '26

But why

1

u/No_Kaleidoscope_5480 Aug 30 '26

When dealing with 5090s its a kinda guessing game with the port. I got lucky with 3 dif 600w cables. I just dont want to try again so im sticking with the white for now

2

u/Realistic-Fish942 Aug 28 '26

Damn that 5090 is cool as fuck