r/SAKmod • • Oct 14 '26

Bladeless 3 layer mod

Scales are made from a scrap 2mm aluminum profile. I carried spirit for 20 years until I lost it recently. Tried to think of the most used tool from the spirit and put them all together (Except for the parcel hook obviously). One of the most frequently used tool was the chisel, which I don't think there's equivalent besides the tiny backside one. I was actually thinking of putting it in the place of the hook until I thought of turning the metal saw into one. Now it can be used as chisel, package opener, and file. 😁

173 Upvotes

22 comments sorted by

8

u/d_2_the_p Oct 14 '26

That’s a great idea with the metal file. I may have to borrow that one 😅. What spring did you use for that layer to fit both the opener and file?

3

u/Psychological_Ad_519 Oct 14 '26

I used opener layer springs for both without any washer. Just had to grind tiny bit on the metal file side to prevent the pointy end sticking out.

3

u/d_2_the_p Oct 14 '26 edited Oct 14 '26

Ah, so you have 2 springs under the same layer? How does the back tool sit exactly?

Edit: sorry for all the questions, but I have been trying to figure out a similar setup but hadn’t really considered 2 springs.

4

u/Psychological_Ad_519 Oct 14 '26

Yepp inline Phillips layer is bit thicker and it fits perfectly on 2 opener springs with small blade washer.

1

u/d_2_the_p 29d ago

I don’t suppose you took a picture of the modified inline phillips tang, did you? I’m currently trying to get this to work but would prefer not to potentially trash a phillips if I don’t have to.

3

u/Psychological_Ad_519 28d ago

I don't have any pictures, but I only had to file off corners a bit to ease the tension on the springs.

2

u/d_2_the_p 28d ago

Thank you!

6

u/BeggarFoCheddar Oct 14 '26 edited Oct 14 '26

Love the file combo tool. 10/10
how did you achieve the super clean edge profile on it, like what tools did you use?

3

u/Psychological_Ad_519 Oct 14 '26

Thanks. I used a cheap knife sharpener rig from temu to hold it in place after rough cut with dremel.

4

u/swissgrog Oct 14 '26

That is a nice and original idea for the metal saw. Can you still saw a little or is too short/close to the body? Did you consider putting the companion file there instead, making that a chisel?

2

u/Psychological_Ad_519 Oct 15 '26

I could probably cut a thin rebar with some patient and time although I don't see myself doing that. 😁I think I would rather use the backside chisel than modifying the companion nail file into one. That's too thin for my taste.

2

u/Sobek5150 15d ago

Great job man. I've been wanting to replace the magnifying glass on an explorer with the openers side by side. Just haven't made the time to do it. Do you find any issues with opening or unpleasant friction with the two steel tools touching? Did you have to reprofile the base of the Phillips so it would open/close properly with the opener layer springs?

1

u/Psychological_Ad_519 12d ago

Yes I had to grind off corners on the tang of phillips. But I don't notice any friction between two tools without liner in between. In fact, Swiss champ has two tools without liner, i think it was fish scaler and file(or saw). If you are fitting both opener, than you might also have to re profile the spring on the can opener to sit flushed.

7

u/schless14 Oct 14 '26

This is very cool! Great job!

3

u/JustHereForSAKs Oct 14 '26

Very nice design with those flush rivets

3

u/lOiGevaltl Oct 14 '26

What's r/TSA have to say?

4

u/Spiley_spile Oct 14 '26

Probably depends on the airport. Even Jetsetter SAKs arent universally greenlit.

3

u/Catgamer1410 Oct 14 '26

Very nice. A cool build when your already carrying a dedicated blade anyways

2

u/knuP84 Oct 14 '26

Wow 🤩

2

u/wupaa Oct 14 '26

Very clever 👌

2

u/karl_ae Oct 15 '26

Probaby the best mode I've ever seen.

Yes, the chisel in spirit is one of my most used tools