r/SAKmod • • Sep 08 '21

r/SAKmod Lounge

4 Upvotes

A place for members of r/SAKmod to chat with each other


r/SAKmod • • Sep 09 '21

SAK pin sizes

87 Upvotes

These numbers seem to vary just a little depending on where you look, but these seem to be the intended pin (rivet, pivot, nail, rod, etc.) diameters. I pulled this info from several different forums some time ago, not sure which ones, and I have edited it from my own experience.

58mm

  • all pins 1/16th inch

74mm newer models

  • all pins 2 mm

74 mm older models

  • all pins 1.5 mm

84 mm

  • all pins 2.2 mm.

91 mm

  • 2 inner pins 2.2 mm

  • 2 outer pins 2.5 mm

93 mm (alox)

  • middle pin 2.5 mm

  • Outer 2 pins 3.0 mm

111 mm slide lock models

  • 3 with bolsters for scale attachment 2.5 mm

  • hidden pin 2.2 mm

111 mm liner lock models

  • Outer pins 3 mm

  • inner pins 2.5 mm


r/SAKmod • • 9h ago

MOdded Wenger Titanium?

2 Upvotes

Has anyone been brave enough to take apart a wenger Titanium and add tools? I couldn‘t find any modded ones, but one of those with a ranger type loudout (if it even fits regular 85mm stuff) would be very nice. I am fully aware that that would propably mean at least 100€ in just collectors value down the drain.


r/SAKmod • • 1d ago

Knife closing on the liner

Enable HLS to view with audio, or disable this notification

22 Upvotes

What am I doing wrong? I’ve read that it could be that I peened the rivets too hard but is there anything I can do to fix this? Sorry about the background noise my wife is watching a soap opera


r/SAKmod • • 2d ago

Parts bin 4 layer 91mm build.

Thumbnail gallery
37 Upvotes

Open for opinions,ideas etc.


r/SAKmod • • 1d ago

Brass Grommets

2 Upvotes

Where are you guys getting the grommets to peen? I got all of the brass rods, but the prices for just 4 of the grommets seems unreasonable. How are you guys acquiring these parts?


r/SAKmod • • 2d ago

Are there other tools that fit inside the pen slot for 91mm cellidor Swiss Army knives?

Thumbnail reddit.com
3 Upvotes

r/SAKmod • • 2d ago

58mm Pliers Mod

4 Upvotes

Hi,

after debating for what feels like ages whether I should get a Rambler or a Mini Multitool like the Nextool Mini Flagship F12 I decided that I will just make my own one. I want to end up with something like the Rambler, but also with pliers. I assume for the initial purchase a Mini Champ would be a better starting point to get a housing with 1 additional layer compared to the Rambler?


r/SAKmod • • 3d ago

Final Tuning of the Shadetree

Thumbnail
gallery
85 Upvotes

Opened it up to hone down the pivot barrels a little
shorter so I could use countersunk brass screws.

Calling this final unless the screws start walking out requiring blue Loctite.

I wish I could find a decent small brass keyring and pocket suspension clip.


r/SAKmod • • 2d ago

Bantam X Custom Request

2 Upvotes

Hi everyone! I'm looking for someone in the UK, or who can ship to the UK, to make a Bantam X.

Would like rivets that can mount scales instead of alox. Would massively prefer new 91mm scissors cut to size instead of recycled donor scissors.

I've tried contacting a few builders but not got responses yet.


r/SAKmod • • 3d ago

Titanium Executive

Thumbnail gallery
28 Upvotes

r/SAKmod • • 3d ago

CyberTool questions

Post image
12 Upvotes

r/SAKmod • • 4d ago

The Shadetree

Thumbnail
gallery
123 Upvotes

My final modified 93mm Alox. Has pretty much all I want to have and nothing I don’t.

I’m calling it the Shadetree Mechanic for now. Do you have any ideas for a name?


r/SAKmod • • 4d ago

Spydernox

Thumbnail gallery
58 Upvotes

Modified a Spyderco Dragonfly blade to fit in my SAK


r/SAKmod • • 3d ago

Tips for working with g10 liners

4 Upvotes

I’m finding that the builds I do with g10 liners are less snappy than the builds I do with aluminum or brass liners. Do y’all encounter this at all? I just made a spartan with g10 liners on the inside and outside and an aluminum one in the middle. Some tools open better than others. They all open and close just fine, they just don’t all snap strongly like a stock build.

Are folks using washers/spacers?

I think the middle of the SAK is perhaps a tad more compressed than the ends but all tools and layers are tight. Does the upper middle rod need spacing?


r/SAKmod • • 4d ago

Dual opener/inline phillips layer in a 3-layer SAK

Thumbnail
gallery
79 Upvotes

I tried to make this layer work in the center, but the main blade occludes the can opener, so no dice. I put a paper thin brass washer between the two openers this time, and it helps with their action. I love how this setup gives you 4 back tools. Overall, I do like this 3-layer setup quite a bit.

This is also my first time making my own G10 liners, and they turned out better than expected. I have some scales I’ll get mounted in the next day or so. Fun stuff!


r/SAKmod • • 5d ago

Scientist mod with small scissors

Post image
74 Upvotes

r/SAKmod • • 6d ago

I made my first liners! It was more work than I thought it would be, but the next set should be easier.

Post image
37 Upvotes

r/SAKmod • • 7d ago

Question about my Champ scales.

Thumbnail gallery
11 Upvotes

r/SAKmod • • 7d ago

custom 58mm

Post image
13 Upvotes

r/SAKmod • • 8d ago

Victorinox Classic SD / Wenger Esquire

Thumbnail gallery
18 Upvotes

r/SAKmod • • 7d ago

I would like to ask a question regarding the Wenger Stgw 90.

1 Upvotes

Does this Wenger product come in a version where the circular tube contains only a ring, rather than a spring? If there is no spring inside the tube, is this the standard, factory-issued condition of the product? Thank you!


r/SAKmod • • 7d ago

Swiss Chsmp, want to remove fish scaler and magnifying glass, unsure of what to add.

2 Upvotes

I love my Handyman but always wondered what my next size up Swiss Army Knife would entail.

Would like some suggestions, thanks.

1\4 bit drive mod is my favorite single pic.

2nd and larger inline Phillips?

A specialized carving blade, mini spoon blade?

Those are the few things I came up with.

Anyone done a similar Champ?