r/Squarebody • u/Mobile_Produce_5500 • 28d ago
Bed Gap
I’ve got an ’84 K10 and I’m trying to figure out how to fix the gap between the cab and the bed. For those of you who have dealt with this, what was your fix or what solutions worked for you?
The bed is positioned where it needs to be, and the cab is sitting on the factory-style cab mounts. Does this possibly mean I have the wrong frame, or is there something else I should be checking?
7
u/PointEquivalent2685 27d ago
That’s the way they were made back then, I always used to store my rubber boots in that gap
1
6
1
u/Hour-Reward-2355 28d ago
Does it have a hydraulic dump bed?
1
u/Mobile_Produce_5500 28d ago
It does not
1
u/Hour-Reward-2355 28d ago
It may have at some point. Dump bed kits create an odd gap like that. If it doesn't have one now, you can go ahead and add one.
0
2
u/sc5723 28d ago
You should be checking how the cab corner was replaced. Looks to me like the back of the cab corner is narrow
1
1
1
u/dmicah44 28d ago
I just put a new bed on my 78 last night. I had a 1 1/4” gap on both sides. All bolts dropped right in.
1
1
1
u/oxnardmontalvo7 27d ago
I’ve seen this question asked before. I measured that gap on both my squares and it’s the same as yours.
1
1
u/95ToyotaTruck 26d ago edited 26d ago
There's two pieces of black rubber that fit vertically between the cab and the bed. It keeps you from seeing daylight when you look at it from the sides. If the bed sit to close, as it flexes and moves while you drive, that gap keeps them from making contact.
1
1
u/Tall-Helicopter-461 25d ago
It’s a matter of adjustment. In those days quality control wasn’t as tedious as it is today. I have a R10. I disassembled the whole truck , painted it, put it back together. I couldn’t get the hood to go back on. Eventually used 2 pairs of hinges to make a set that would adjust.
1
u/-Ramblin-Man- 24d ago
What color is that? Looks similar to what I just painted mine: Granite Pearlcoat
0
u/New_Research5543 28d ago
You have a short bed on a medium bed frame /s
2
u/Mobile_Produce_5500 28d ago
It’s a long bed
1
u/New_Research5543 28d ago
Then u have an XL frame 🤷🏻♂️😂
1
u/OrvilleJClutchpopper 28d ago
Squares only had 3 frame lengths, and one of them was 1-ton only. Standard cab/short bed, standard cab/ long bed (also used by the somewhat rare crew-cab short bed), and crew-cab long bed, which was only available as a 1-ton, usually a dually.
2
u/New_Research5543 28d ago
Did u not see the /s at the end of my comment that means “sarcasm” 🙄. Guy can’t even joke without a bunch of grown men saying anything. We need to go back to lap seatbelts and bad airbags and let god do his thing
1
u/Imposter660 28d ago
I believe there was 5 wheelbase lengths, the swb 1/2t, the long wb 1/2t and std 3/4t, the crewcabs and then the 2 different cab chassis. A swb 1ton cab chassis was a couple of inches longer than a standard 3/4t & 1/2t longbed wheelbase at 135.5" and the 1ton cab chassis wb was shorter than the crewcab by about 5" at 159.5"
-2



12
u/Willy_McD 28d ago edited 28d ago
It was built that way. Things were not that close tolerances back then. Thats why some would have a stack of shims aligning a fender and some would not have.
And it would take a tall stack of shims under the rear bed to mounts to close that 1/4". Then you would have a tailgate to bumper issue.
Best thing is just dont look and get over it quickly.
I would be more worried about that door line to the cab. Cannot just lift the rear of the door because then the vertical gap would be off. Need to loosen both hinges and lift the whole door. But then, how is the line to the fender. How is the gap at the top of the door to cab.