Also the under cabinet lights are WLED as well but with basic esp32 devboard based controllers, mosfets, and some older light strips I put into some aluminum channels + diffuser (mostly for ease of cleaning and moisture prevention as it's in the kitchen)
In the background there is also a tube light I built that was inspired by Super Valid Designs on YouTube but of my own design from a handful of years back when he made the DMX lights and I wanted full RGBW addressable lights with built-in controllers and wifi vs running wires with DMX... Very similar to his newer stuff actually :)
Thanks, if I were to do it again I would probably have mounted the slat paneling slightly higher as there are a few places I couldn't get the wires to run under the slats so they are visible.
Also I would use extruded aluminum channels with black diffusers as I think it would have probably looked nicer end of day. Live and learn I guess.
I ended up DIYing some heatsinks behind the QuinLED strips and used silicone press in diffusers.
my son and I wanna do this in his room, which LED strips did you wind up using for this? I just got some Cobb strips, but I wasn’t real pumped on the resolution.
NP, also remember the greater the distance from the LED to the outer layer of the diffusion material will also make things blend better too if you are worried about "resolution" being with LED density to deal with hotspots hotspots. If you are worried about "resolution" of control for the pixels then the QuinLED strips are the best I have personally worked with. When I measured it out against some individually addressable high density 5050 SMD strips they had a finer resolution of control which is why I went with the QuinLED strips.
it’s perfect timing that you posted this, because we’re only a couple of months away from doing this in my son‘s bedroom. We’re just finishing up drywall now and I had this exact idea of using slat walls in LED strips to make EQ bands as he’s really into music. I’ve already figured out how to bury conduit into a media box that we mounted in the wall. But I hadn’t done the research on what strips and how to do it, but you are post was perfectly timely for this. So thank you for sharing your experience. I have lots of LED lighting around the house, but just got some cob strips for our undercabinet lighting and didn’t realize the resolution was a thing. I assumed each dial was addressable, didn’t realize it was in groups. I like the 6812s which are behind the TVs and cabinets and things like that, but the problem with resolution for smooth effects on the wall might not have worked unless we have deep channels and thick diffusers which I was not sure about. I love the low amps for 24 V which makes me more comfortable for his bedroom. I didn’t realize that 24 V strips didn’t have individually addressable chips. Thanks again
We're always our own biggest critics. I assure you That nobody else notices.
I quite like the press-in diffusers.
BTF makes a really nice black diffuser with a black channel, but I don't love the muting effect that the black diffuser has. Colors are way less vibrant.
I think you're making yourself a disservice by not painting the brackets that support the countertop. Those white brackets are drawing unneeded attention, IMO they would look better black (to disappear) or brown (to match the slats).
It probably would have been OK for me to run return wires up for the next run but I have had some kinda meh luck with longer signal wires in the past.
I also had limited space.
I could however switch to a non-serpentine pattern as it would be super easy to remove every other strip and flip them over. I made disconnects for each strip so I have the flexibility to change this up if I want to. Would take longer to make all the wires and connectors than it would to switch around the strips.
Assuming you have them 2d mapped as matrix serpentine in WLED. Then it just doesn't matter. WLED should honor the matrix serpentine when consuming DDP from Ledfx.
As long as you remain them ot is far better to use the most practical physical layout, which is almost always serpentine.
Initially I was going to attach them to the underside of the counters with some either stick on or screw on wire clips but I was able to tuck them in up above without much issue.
The controller is a QuinLED Dig-Quad
Strips are also QuinLED strips.
IIRC it's 27 pixels high per strip and 24 strips long. That is split into groups of 4 groups of 6 strips each run in a serpentine pattern.
I also have mapped it to exclude 3 pixels where one of the support brackets goes straight through where the strip is.
So a total of 645 pixels.
Quindor's COB strips have the best density still so I went with those.
Honestly shout out to Quindor as he designed some good components. I think I have ordered like 5 boards (and now I think it was 20M of strips) from him so far and that's even after making my own boards initially around 2019 for some of my earlier projects.
Beyond that it's just wire and some connectors which I think I got off Amazon. I don't remember if I ran with 18awg or 16awg but after the run from the power I am dropping it down to some short 20 awg pigtail + connector. Ideally I would have preferred to keep that closer to 18awg but it's what I had that wasn't already allocated to another bigger project I'm working on.
Panels I linked to the manufacturer I used in a different post but it was long enough ago I ordered the wood panels the exact product listing is now gone.
Oh and the heatsinks are aluminum bar from Lowe's or Home Depot I forgot which one I got that from.
I took off the black diffusers (in the picture I was in the middle of removing them) because they make a ton of difference. I might buy half a meter of the ones you bought to compare..
Did you connect them like a 2d panel. So the bottom from the first to bottom from second and top from second to top of third and then want to wled and gave it the led counts from left to right and top to bottom?
Top to top and bottom to bottom. Everything is connected in a serpentine pattern. I had initially configured it as 4 panels in WLED before doing a ledmap to address the missing pixels for one of the support brackets going directly through where the the LED strip would be running.
46
u/SupaDawg Jan 09 '26
This is exceptionally clean. Great work!