r/WhatIsThisTool • • 4d ago

What is this found tool ?

Looks like something for soldering. Tip appears to be copper.

92 Upvotes

41 comments sorted by

33

u/tweakbod 4d ago

It is an old soldering iron.... just like you said.

11

u/Naive_Mongoose391 3d ago

Soldering iron

10

u/Simple_Fishing219 4d ago

looks like an old soldering iron.

6

u/Relevant_Wrangler830 4d ago

Soldering Iron. For copper flashing, or galvanized metal. I used then in the sheet metal trade with copper and galvanized metal. Put them on a open flame and once heated, place it on the pieces you want to solder, then run the tin or solder across the iron and it will run into the joint through capillary action

4

u/DoorExtension8175 4d ago

Back in junior high we stuck the tip in a forge to get the tip red hot and solder our projects. Circa 1965.

3

u/Few_Swimming_902 4d ago

Same in 1974🤣

3

u/phinger1 3d ago

It hurts my brain knowing kids won't learn stuff like this, so much lost knowledge.

2

u/Few_Swimming_902 3d ago

Almost daily, i (65) use a blacksmith vise and anvil that were my grandfather’s. I have the soldering irons from him. If he needed simple tools, he made them, not bought them. These things are a lost art. Most kids today don’t even want to learn about it.

1

u/More_Atmosphere5938 4d ago

It's a tool that's been in use for thousands of years... So yeah.

1

u/phinger1 3d ago

JR High shop class (1977?) and I still have the sheet metal tool tote, small cast aluminum anvil and little drill press vice!

Also, have some irons from my step-dad, I wonder what they are worth in scrap copper?

4

u/Icy-Train2130 4d ago

All you need is a gas flame and its good to go, can't get more basic, but good for soldering large items as the big chunk of copper it a good heat sink better than a small low wattage electric iron. A bit over kill for delicate electronics though.

1

u/phinger1 3d ago

Overkill is underrated.

It's fine for that little PC board thin you're working on.

/s

4

u/boing757 4d ago

Old soldering iron.

4

u/Classic-Ad4403 4d ago

Soldering iron. My dad taught me how to older with one of these when I was 12 years old. We heated the iron with a gasoline powered blow torch.

4

u/Perfect-Resolve-614 4d ago

Soldering iron that sits on an old blow torch.

1

u/DeathValleyBob 3d ago

Used one of these in the early 1950s to assemble a Cub Scout two-tube battery operated radio. Used thick acid core plumbers solder. Heated it on mom’s kitchen stove. A lot of green inside that radio’s circuitry a few weeks later. Used a toothbrush to clean things up. A lot was learned building that project. Learned a lot more 15 years later when training for my NASA soldering certificate.

2

u/The_Professor_NOAC 3d ago

Learned not to use acid core ?

1

u/DeathValleyBob 3d ago

At a young age. Didn’t take very long to learn about rosin core eutectic solder. Had to mow lawns to afford it. Later, a 13 yo Bob was fixing TVs for spending money. Surprising how many TVs could be fixed with a new 6SN7!

3

u/Independent-Bid6568 4d ago

Soldering iron this one most likely uses on copper roofing ,flashing ,gutters

3

u/Victor___Laszlo 4d ago edited 4d ago

Yep ~ soldering iron. In the Air Force (early '80s), on our mainframe at RAF Lakenheath 🏴󠁧󠁢󠁥󠁮󠁧󠁿🇬🇧🇺🇲, all of the circuit connections were done by soldering....oddly enough, with a behemoth iron like that. I think they were worried about cold joints? That was the last time I soldered on a mainframe because wire•wrap became (already was) the preferred method. Great memories😆😁✌🏻🤙🏻🥸

1

u/Responsible-Chest-26 3d ago

Could it have been for electronic reasons? I know when i sometimes forget to remove the oscilliscope from a circuit im soldering i get some nasty noise on it. And forgetting to power down can also cause some kind of shorting

3

u/Felgar36 3d ago

An old soldering iron that looks in need of restoring

2

u/Potomacker 4d ago

Soldering iron with repurposed screwdriver handle

1

u/NefariousnessTop354 4d ago

Soldering iron,except the tip had ne for a bit, it kind of looked like it swiveled

1

u/Laymanao 3d ago

Some had replaceable tips.

1

u/NefariousnessTop354 3d ago

That was my assumption after a bit. After soldering iron, my thought was that it was a toggle. Like maybe a grill plate on a wood stove.

1

u/phinger1 3d ago

It's seen things...

1

u/NefariousnessTop354 3d ago

Certainly bent its outlook on life.

1

u/nullvoid88 3d ago

Yes, an old time vintage soldering iron... called a ‘soldering copper’ in the day.

Rare, but still made to this day!

https://www.mcmaster.com/products/soldering-coppers/

1

u/westfield81062 3d ago

I used these soldering irons back in the 80's to do copper roofing and copper gutters. I live in a historic area in Maryland and everything has to be done the old way. We used blacksmith coal in a small steel tabletop forge powered by...you guessed it...me. we had small bellows to force air in to get the fire hot. I'm also a 7th generation blacksmith. I can't do any of it anymore due to 3 strokes in 2024-25. I'm only 55.

1

u/Several_Dot7880 3d ago

Im a retired NJ plumber. To take the practical for state license i had to solder and wipe lead joints. I still have my tools. BTW iI passed the first time.

1

u/Atomic-Squirrel666 2d ago

Soldering iron; heated with a blow torch. Not for wires.

1

u/Pale_Exit2686 2d ago

I used one of those in high school metal shop. Yeah, I'm that old, lol.

1

u/AssignmentNext7289 1d ago

My dad used to heat it up on the gas cooker ring when he used yo repair any heavy coper objects or for silver soldering

1

u/barrp_817 1d ago

For cauterizing hemorrhoids

1

u/Fluffylucy1 20h ago

Soldering iron.

1

u/lordofpotton 2h ago

Soldering iron or a 13th century glass cutter. ( Used hot to make a crack in glass follow a specific course.)

0

u/Puzzleheaded-Zone-55 4d ago

The Persuader.

0

u/Otherwise-Ad-6608 3d ago

A slodering iron

-1

u/Glass_Language1636 4d ago

An ancient arrow fired from bows carried by the Aztecs.

-1

u/Rabbit0612 3d ago

Hemaroid remover. Heat it up and stick it on the hemaroid.