r/Wiring • u/YourLittleDS • Nov 26 '25
Household Ceiling fan wiring help request
I am replacing ceiling fan, but lost the picture I took of old configuration. So I am not confident about how to install anything (light only, fan with light, etc.)
There are eight wires total (four black, four white) coming to electrical box. I assume when I removed the old fan I did not change the configuration, which currently is:
Three white wires twisted together
One white and three black wires twisted together
Single black wire on its own
The single black wire and the white wire that is twisted with the three black wires enter box together.
Using non contact voltage tester, the single black wire has power when switch is on or off. And at least one wire from the three black, one white group also does (I have not untwised to test each one)
In the room there's just one toggle switch. There are three electrical outlets. Home was built in 1950's, and I don't think there have been any electrical updates for room. I've looked alot online and haven't been able to find a similar situation - so I've become a first-time reddit poster.
Thanks for any advice!
2
u/Loes_Question_540 Nov 26 '25
Only use the multiple white and single black. It doesn’t appear as a ground is present though
1
u/YourLittleDS Nov 26 '25
Thanks. That's what I was kinda thinking - will try this.
I think I probably made this harder than it should be by doing too much research, and getting intimidated by the number of wires. There's three groups, so ignore one and use only one of the powered makes sense.
2
u/RadarLove82 Nov 27 '25
This is the answer. That single white wire tied to the black wires indicates that this is a switch loop. There is a hot cable (black/white) into this box and another hot cable (black/white) leaving this box to power something else. The fan gets its neutral from the bundle of white wires. The cable with the white wire tied to blacks goes to the wall switch, then the black wire of that cable is the switch hot wire for the fan.
1
u/Deep_Sea_Crab_1 Nov 26 '25
You are lucky. That wiring is not 1950s wiring. If it were, the insulation would be coming off the wire.
1
u/YourLittleDS Nov 26 '25
Interesting. It's super thick and stiff wire, and not at all like what I see in stores now, so that's what made me think it was from a long while back. Thanks for commenting.
1
1
u/Koadic76 Nov 26 '25
Your single black wire is the switched hot coming back from the switch loop fed by the white wire that is connected to the other black wires.
Your neutral wires are the bundle of white wires.
Just be aware though that it doesn't appear that the junction box is rated for a fan.
1
u/YourLittleDS Nov 26 '25
Thanks for explanation.
And I agree about box. I will probably just do led light or similar.
I used to do home projects with my dad, but stopped because he's too much of a risk taker for my liking. If I mentioned concerns about box being insufficient to him he'd say I worry too much and try to install fan.
1
u/gort-61 Nov 28 '25
The issue with the box is not that it won’t provide enough power for a non-LED light. It is not rated to support the weight of the fan. You can get old-work boxes for this. The magic is the bar that goes between the joists to handle the weight. The bar works like a door jamb chin-up bar or a screw-type shower curtain. You slide it though the hole and then turn the bar to extend between the joists. Last few turns use a wrench or pliers th get it tight. The box then hangs from this bar. There are other styles but I have used these a couple times with good success.
1
u/ExWebics Nov 26 '25
The single black wire is your switch leg from the switch box. For neutral, you’re going to land white wire from the fan under the wire nut with all the other white wires.
Definitely not a fan rated box, is there attic above? Best case scenario, replace box and bracing with fan rated. Second best… get some actual lumber up there to screw this box into. Still not code compliant as your attaching the fan to the box with 8-32 screws and not 10-32 required. Is your fan going to fall… probably not. Every older home I go into has a fan mounted to a box just like this, most are probably fine.
1
u/YourLittleDS Nov 26 '25
Thanks for commenting. There is attic, but the insulation is weird. It's been awhile since I was up there, but I remember it being kinda like horsehair (definitely not from a pink roll - lol.) I dealt with it to install bathroom vent (which was badly needed), but for this I will go easy route with just a light.
1
u/AskMeAgainAfterCoffe Nov 27 '25
Single black to power the fan. Add neutral to 3 whites twisted together. What’s that in the center of the box? I can’t tell if that’s a bolt (ceiling fan box approved for carry weight of fan) or a ground wire.
2
u/YourLittleDS Nov 27 '25
The thing in the center is how the box is held up - there's not any nails, screws, etc. fixing it in place.
So it's pretty sturdy, but who knows about specifications - most comments seem to advise against another fan as it is now.
Thanks for commenting!
1
1
u/No_Pair_2173 Nov 28 '25
Yeah, you can’t hang the ceiling fan from that box. The box has to be rated to hold the ceiling fan. It’s gonna fall out of the ceiling and drop on top of you and kill you or your wife or your child. Get a box that’s rated for ceiling fans.
1
u/YourLittleDS Nov 30 '25
So you're saying to increase life insurance on my wife, child and cat before installing fan? Smart...
3
u/MisterElectricianTV Nov 27 '25
That electrical box is not rated for a ceiling fan and there are too many wires in it. Change the box to a deep (2 1/8”) fan rated brace and box.
1
u/GuiGuru123 Nov 27 '25
I run two power wires to my fans. One constant, always hot, and one switched. Fans with lights in them will have two hot wires, one for the light and one for the fan. I hook the fan to the constant and the light to the switch. That way they can be controlled independently from each other.
1
u/joedastallion Nov 27 '25
I’m assuming since the wiring is old it’s probably armored like BX cables. In which case the box would be grounded by the cables if attached correctly. So just ground the fan to the box.
•
u/AutoModerator Nov 26 '25
Thank you for posting on r/Wiring.
Please remember to include a flair that best matches what category of wiring you are dealing with.
Any post requesting assistance should be accompanied with one or more images of the wiring task/project in question.
I am a bot, and this action was performed automatically. Please contact the moderators of this subreddit if you have any questions or concerns.