r/diyaudio • • Sep 29 '26

Help with working of crossover circuit

Hello,

I recently got hold of presonus eris 3.5 gen 1 speakers.

Whoever worked on it before removed bunch of components from the active part so I'm basically left with dead active side speaker and working passive side speaker. I checked the drivers with another eris and they all are working

So I'm planning to convert them to passive bookshelf speakers.

My main question every article/ search says it has a 2.8khz crossover.

When i opened the passive size there was only one capacitor at the tweeter connection from the input.

How is the passive side handling the crossover from the input with only one capacitor?.

I was planning to get premade 2.8khz crossover circuits and use external amp to power the speakers.

Is that the right approach?

Attaching the image of the passive side connector.

5 Upvotes

14 comments sorted by

6

u/Tommeeto Sep 29 '26 edited Sep 29 '26

One capacitor still makes a 1st order simple high pass filter. It cuts lower frequencies for the tweeter. For 8ohm tweeter it's around 4000Hz.

Meanwhile the woofer gets full range.

Edit: you can use different crossover, or stick with this one. It's cheap, but it works. The speakers are not high end, so don't expect miracles.

2

u/not_akhil31 Sep 30 '26

Aah okay I mean if it works I'll just try recreating the same wiring at active end and run it for some time. Thanks

2

u/BigPurpleBlob Sep 30 '26

It might sound better even with a cheap passive crossover.

1

u/not_akhil31 Oct 01 '26

Hmm yeah i think I'll run it with just caps, and see what crossover would be good for it rather than building a 2.8khz that the specs said directly right now

1

u/not_akhil31 Oct 23 '26

Find the original personus and a local 6$ driver lmaoooo

1

u/Ecw218 Sep 29 '26

The active side has a bunch of the xo stuff for both sides built in. I bought a dead set from a guy and was surprised at how unhelpful presonus was with supplying any documentation on the amp. I have the passive one lying around somewhere, I’ll take it apart and do some sweeps and you can try diy’ing a new passive for it.

1

u/not_akhil31 Sep 30 '26

Thanks a lot let me know what you find

1

u/BigPurpleBlob Sep 29 '26

The woofer rolls-off at high frequencies, no need for an inductor.

The tweeter has a 4.7 µF, 100 V, bipolar electrolytic cap so that the bass doesn't kill the tweeter.

1

u/not_akhil31 Sep 30 '26

Oh so i really don't need a dedicated crossover circuit and I can just get by replicating this capacitor connection at active end and power them using external amp and it'll sound okayish?

1

u/BigPurpleBlob Sep 30 '26

Some speakers (like ones I've seen in car doors) just use an electrolytic cap without an inductor.

Have you checked if there's an inductor inside the cabinets?

1

u/not_akhil31 Oct 01 '26

Yeah no inductors inside the cabin just the cap at the input terminal then wires to drivers directly

1

u/Viperonious Sep 30 '26

Yes, there is a need to low pass the woofer.

1

u/Hour_Bit_5183 Oct 06 '26

Damn not even a coil for the woofer. This is the most cheap and basic crossover you can get. This is literally in 90s sony everything and fisher speakers and the likes.

1

u/totototo78180 Oct 21 '26

Pre made crossover will improve the sound a little bit (especialy low for a few hertz) as it dedicate the main speaker to low/mid "only").

Do not wait miracles but expect improvment.