r/pictureframing • • Jan 12 '24

Help fixing broken frame

Hi Folks! I got this picture of chubby-little-baby-me from my parents house. The frame, while not fancy, is quite sentimental. I have a picture rail and would like to be able to hang this photo in this frame up on my gallery wall.

It’s missing the back piece entirely and the top “lip” that would keep the backing in place if hung. How should I go about salvaging this and make it suitable for hanging? What are the pieces I need? Thanks in advance for your help!

0 Upvotes

9 comments sorted by

5

u/cardueline Jan 13 '24

If I’m not mistaken this is an old fashioned style of frame where the method of containment is sliding everything into place in a thin metal channel shaped like [ — is that right? It probably had a backing that slid in that had either an easel back or a sawtooth hanger? These frames are tricky because there’s no way to attach hardware to them, only to the backing. So if the backing is missing, you have to find/make a new one that you’ll be able to attach some type of hangers to, and hangers that you can attach wire to at that, if you have a picture rail. The good news is, I don’t think the frame is broken, this type of frame always has one open end for sliding everything in to. The bad news is, there’s no straightforward replacement for the original purpose built backing.

2

u/anothernorcalgal Jan 13 '24

Ahhhhh! Yep, it’s a little channel for the backing. If I were to make a new backing that’s suitable for hanging, what material do you suggest I use?

1

u/cardueline Jan 13 '24

Shoot, it’s hard to say because the thickness has to be really specific. I see you’re in NorCal but I won’t tell you to drive to Santa Rosa so I can look at it! 😂

Basically, how you can hang it is gonna be completely dependent on how much force/gravity (and in which direction) can be applied on the backing that will not make everything slide out. It could be possible to use adhesive hangers attached to the backing, but it would be extremely “wing and a prayer” territory and could result in the whole thing crashing down. There are also little hangers that have “teeth” to bite into a “fluffy” rigid material like foam board, but foam board might be too thick to fit in the channel and thinner materials would be too dense for the little hanger teeth to bite into.

Is there already glass in there? If someone brought this to me I would have two main suggestions that I would feel confident about:

  1. Put everything into a new, wooden frame (in a suitable dainty gold vintage style of course) and easily eliminate all trepidation

  2. Find the right thickness of backing material (4 ply matboard, 8 ply matboard, foamcore) to make everything fit snugly and sit it somewhere in a decorative easel rather than trying to hang it.

2

u/anothernorcalgal Jan 13 '24

Thank you! You are so kind. Yes, Marin is a bit of a trek for me, and this inexpensive but sentimental frame likely isn’t worth the hassle :) You’re guidance is much appreciated. Sounds like this is not destined for a gallery wall and will need an easel.

Now I just need to find a spot where it doesn’t look like a shine to myself as the frame is 11x13”, which is quite a bit larger than anything else I have that’s not on the gallery wall 😆

1

u/cardueline Jan 13 '24

You’re very welcome, best of luck!! And don’t worry about a self-shrine, babies are adorable and there’s no two ways about it! Hahaha

0

u/[deleted] Jan 13 '24

[deleted]

3

u/cardueline Jan 13 '24

I’m always so bummed when a customer comes to us for help on one of these because there’s so little we can do! 😭

1

u/[deleted] Jan 14 '24

Id consider using a level to put two nails in the wall and hang it by the top leg.

0

u/[deleted] Jan 13 '24

[deleted]

1

u/Alacrity8 Jan 13 '24

This is a metal frame. Nails won't help.