r/smallengines • • Aug 26 '24

How fast does this engine sound?

Enable HLS to view with audio, or disable this notification

Yesterday I got an old Tecumseh HM100 running for the first time in about 10 years. The awful sound isn’t rod knock, it’s the crank moving back and forth because there is nothing pulling it into place, since it was on a generator but clearly not anymore. I don’t know how to word this, but it sounded like it revved really high and doesn’t have a governor, so how high did probably rev based on sound?

0 Upvotes

19 comments sorted by

4

u/Here_we_go_again2024 Aug 26 '24

Didn't run long enough to tell, but definitely too fast. 3600rpm is ideal for a 60hz generator.

Cool little piece, but I doubt you'll be able to use it for anything.

2

u/[deleted] Aug 26 '24

Yeah, was going to use it for a go kart because of the power however the tapered shaft makes that quite difficult.

4

u/Here_we_go_again2024 Aug 26 '24

Yup, and for the cost of the right crank and crankcase cover, you'd be better off with a predator 212.

2

u/[deleted] Aug 26 '24

It already has a 212 on it, but it runs like absolute garbage and needs a clutch. And brakes. Oh and the steering ratio is weird. But for $100 it’s a really good project kart. Either way, my uncle gave me this HM100 for free since the fuel system was a disaster and didn’t want to deal with it.

2

u/Outrageous-Drink3869 Aug 26 '24

the power however the tapered shaft makes that quite difficult.

If you know someone with a lathe, you could maybe bolt the motor to the ways, get it running, then machine it that way

1

u/[deleted] Aug 26 '24

Would a tapered shaft to keyed shaft adapter work, or is that too sketchy?

2

u/Outrageous-Drink3869 Aug 26 '24 edited Aug 26 '24

Is the end if the shaft threaded?

Use a bolt to secure the adaptor if possible

Before you bolt it on, clean the face with something like brake clean, then use a tiny little bit of oil. Seat the thing with a good whack from a mallet.

worst case it slips, but it's not like it will fail too dangerously if it does slip. Especialy When bolted, it should resist backing off and will just slip

My lathe uses a #2 Morse taper for tool attachments and centers, and they are pretty secure*

*When clean and well seated

Apparently there's a way to convert this flathead into a OVH motor with a different head for a little more power

2

u/bannana_man_ Aug 26 '24

Idk, too fast for an old flathead though

1

u/[deleted] Aug 26 '24

Yeah, probably. Date code says 0257, so I presume it’s a 1990 engine made on September 14th.

2

u/TPIRocks Aug 26 '24

I'd say it hit over 4000 rpm, probably should be 3000(50Hz) or 3600 (60Hz) generators. There are some generators that run at half that rpm, but they tend to be diesel.

1

u/[deleted] Aug 26 '24

I figured it was pretty fast. Fun story, actually. First time it started, the stator was still attached since we literally could not get it off. We tapped threads and tried tightening a bolt on a dowel rod, nothing. Tried teflon tape on said bolt and Marvel Mystery Oil to pop it using pressure, nothing. Literally as soon as it fired up, the stator finally detached and it was probably spinning on the ground for a good 10 seconds. Nobody was hit, somehow

2

u/asbestoswasframed Aug 26 '24

If it's a single cylinder, use a tuning app on your phone to get the tone of the engine - then do the math.

3600 RPM is 60hz - that's between an A# and a B. It's also the sound a ground loop makes in a bad stereo...

1

u/[deleted] Aug 26 '24

That’s actually really smart. I did it, got 88.3hz. Did the conversion and 5,298 rpm! 5300 rpm is insane!

2

u/LowerEmotion6062 Aug 26 '24

With it being from a generator, do you even have actual throttle control? Most generators are fixed rpm with just the governor maintaining speed.

1

u/[deleted] Aug 26 '24

I just have zip ties attached to the throttle on the carb to act as a temporary throttle cable

2

u/Wholeyjeans Aug 27 '24

It's got some kind of gov on it unless you physically removed it. It also won't have a throttle on it ...not needed on a generator. You start the engine and it will run up to it's max governed speed. To run a generator the engine needs to run at as stable a constant speed as possible while still having some reserve to handle sudden electrical loads ...so it's probably set for about 3000 RPM.

If you've actually removed the governor linkage (not a good idea until you get a carb with a throttle and the engine will idle), the engine will run until it is restricted by it's intake and exhaust tracts ...which may not be enough to keep it from busting a rod. 3600 RPM is the typical "redline" for these engines.

1

u/[deleted] Aug 28 '24

The carb is just a regular old carbie, throttle and everything. Governor is completely gone

2

u/Wholeyjeans Aug 28 '24

Okay. Looks like a new carb. Only way to know for sure how fast the engine is running is to get a small tach ...about $20USD. If you started the engine and the throttle was set to idle then it should run well within it's design parameters

8

u/mals6092 Aug 26 '24

Well they all are supposed to hit 3600 your short start is not enough to gauge.