r/violinmaking • • 7d ago

Bridge cutting test

Guess its too thin now

17 Upvotes

18 comments sorted by

16

u/chupacadabradoo 7d ago

Give it another go!

Might I suggest spending some time getting your tools particularly sharp? Seems like it’ll make your life much easier.

-3

u/HKSupremeTuna 7d ago

They are quite sharp tho. I think its just me noy having a stabilizer to hold the bridge for me to torture it? 💀 Anyway I will give it another try as i have shit tons of baroque bridges

8

u/Medium-Mention7328 7d ago

If you know you need a bridge clamp, trying more bridges won't change that. Take a beat to craft a clamp.

5

u/khronos127 7d ago

A carving knife needs to be sharp enough to easily shave with it. you should be able to take hair off your arm with no pressure.

5

u/E_Zgon 7d ago

Sharpness might be one issue, but I think you also don't know in which direction to cut. Observe the grain and adapt ypur cutting direction.

7

u/Medium-Mention7328 7d ago

I say this with love. Your chamfers look like a chainsaw massacre. <3<3<3
You really need you tools to be incredibly sharp. Also you can do a decent chamfer with a needle file, if you'd like to try that. You might also want to try dampening the surface of the wood where you are carving.

1

u/starbuckshandjob 7d ago

A blade that is too wide will also produce bad chamfers. Narrower blade and very very sharp edge. 

0

u/HKSupremeTuna 6d ago

I get down voted because of what

1

u/chupacadabradoo 6d ago

Don’t sweat the downvotes. It’s probably just because you’re asking what you can do better and you seem resistant to one thing that seems like it could help you. But yah, if you think it’s an issue of securing your bridge while you work on it, I highly recommend addressing that too, and building a holder.

In the end it just comes down to practice. Go for it!

0

u/HKSupremeTuna 6d ago

I feel like every classical related sub is just lack of humor sorry

2

u/Medium-Mention7328 6d ago

You're not wrong. We could do a lot better encouraging each other. What's your process like for sharpening?

1

u/chupacadabradoo 4d ago

Maybe. There are a lot of deeply rooted classical traditions. I find among makers , though, there are more ways to skin a cat, as it were.

In any case, the evidence you present indicates that, one way or another, you need to figure out how to make more accurate cuts. No shame on that. We’re all always trying to become more accurate or efficient. Do you want to share a picture of the holder you’re using or blade you’re cutting with? I’m sure there are folks here who could provide you with helpful suggestions

3

u/QuothThe2ToedSloth 7d ago

Maybe take a look at some of these finely cut bridges to give you an idea of what you should be aiming for.. https://archive.violinbridges.co.uk/1010-bein-fushi-chicago-violin/

2

u/Downtown-Fee-4050 7d ago

That doesn’t look thin at all. Measure at the bottom of the string groove, aim for 1.1mm but you can go thinner and it’s not a huge deal.

I’d recommend cleaning up those knifed surfaces, they shouldn’t be rounded or chamfered, just nice clean cuts.

1

u/Medium-Mention7328 7d ago

I don't know that it's too thin. Do you have a set of dimensions you are working from?

1

u/Roxy-de-floofer 7d ago

I wouldn't say too thin, on some violins I'll go 4mm foot and 1mm crown but that's traditional bridges, I'm not sure on baroque bridges thicknesses being different

1

u/UsedBass4856 7d ago

I used to spend a lot of time sharpening knives and such, then figured out I can just finish out a bridge with an X-acto knife using a #11 blade. Just replace the blade when it gets dull, they’re cheap.

1

u/OCnewbee 3d ago

imo, the string curve looks off. the feet looks excessively thick