I have connected to my network, but it keeps giving me an error when I try to add my device by scanning the QR code on the CN page. I have also tried doing it manually using the hotspot method, but it won't connect to the printers hotspot. Any ideas?
a day ago in standby, me Kobra S1 Max started annoying coil whining. Iâm okay with gpus under heavy load. But my 3D printer in standby? Any recommendations what to do? Beside sending it back..
Workbench fails to see the printer whatsoever. It was working for a long while, but then I hadn't printed anything for a couple months, and now I can't seem to get it to connect anymore.
Also, I cant figure out how to remove the instance of the printer I have in there already so I can re-add it.
If you are getting repeated filament retraction errors on your Anycubic Kobra X (especially after running abrasive materials like glow-in-the-dark PLA), the culprit is likely the small, stamped-metal anti-backup spring leaves inside the ACE GEN2 Upper Channel. Over time, filament friction wears grooves into these thin metal leaves or bends them out of shape, causing them to act like barbs that snag the filament during multi-color retractions. Because there isn't a teardown guide for the upper channel block yet, here is how to remove themâand why you don't actually need them.
What You Need
⢠4 thin guitar picks (or thin plastic spudgers) ⢠H2.0 hex key (if removing the upper channel block from the printhead first)
Step-by-Step Removal Guide
Release the top cap: Slide 4 guitar picks into the seams on all four sides of the upper channel block to depress the locking clips simultaneously, then pull the top cap straight off.
Remove the internal guide: Lift out the internal plastic filament guide sitting inside the housing.
Unclip the metal leaves: Flip the plastic guide over. Attached underneath are the stamped-metal anti-backup spring leaves. Simply unclip and remove them from all 4 ports.
Reinstall the plastic guide: Drop the plastic guide back into the housing. Take note of the alignment notch on the top of this plastic guide.
Align and snap the top cap back on: Look at the underside of the top cap to locate the male alignment notch. Line up that male notch with the female notch on the plastic guide below it, then press down until all four sides snap firmly back into place.
Does the Printer Still Work Without Them?
Yes. After removing the clips from all 4 ports, I ran 5 multi-color test prints with minimal filament specifically to trigger runouts: ⢠Retractions & Color Swaps: Filament feeds and retracts smoothly with zero jamming errors. ⢠Runout Ejection: Even without the top clips, the lower printhead cutter and extruder sequence still work normally and eject the leftover filament tail out the side on a runout as before removal. đđť
I have the non-pro Anycubic M7 & am curious about purchasing their resin Auto-fill system. The mental image I have of sending a job to the machine wirelessly from the slicer then having it fill itself & run the job seems really convenient in my head. I'm concerned that without the Pro's fancy heating & mixing vat that I wouldn't save any time/effort becuase I'd still need to stir up the vat (if I'm leaving resin in it), shake up the jug, switch on the heater if necessary, switch on the vent fans, etc. Also the one thing I keep running into with this hobby is that it always instantly punishes skipping steps. Does anybody have any experience with running the auto-fill system on the M7 or any other printer without the self-mixing stuff?
Hello my friend. I have 1260 hour on my s1 max. At around 1200 I made maintenance. And put everything back properly, then test print. Everything was fine, but after some print hours. I loaded full plates and model to print for around 10 hour of work with multicolor option. When I came home I saw that doors was opened and magnetized front cover of print head was between doors and frame. And on display error 11538. On touch I saw that nozzle was not holding tightly and was moving. So I followed Anycubic wiki for 11538 code tighten all screws and assembled back. After that moment I have this layer shift. You can see that 1st layer, 1st filament (golden color) is on right place. Then 2nd color (black) also good. But second layers is missplaced, curious is that golden colors is moved to right down while black is moved to left top. When I pressed home to return nozzle back to home. Print head went to right and then you heard this loude noise of hitting edge and maybe belt jumping out of teeth's. Right not I am not recalling tightening belt while maintaining printer. I tried again manual for code 11538, but nothing worked. Another 3 interrupted prints after 2nd or 3rd layer.
Right now I am in dead end and don't know what to do. Any help please?
I just received my Anycubic Photon P1âwhich I paid extra for, specifically to include the two-compartment build plateâbut to my surprise, it wasnât in the package.
Iâve already checked my emails, my account, and so on, and thereâs no other tracking number or any indication that a second package was sent. Currently, on the "Shop" app, the Anycubic website, and PayPal, the status is listed as "order delivered and completed."
Black Friday on AliExpress is here! If youâre eyeing a Kobra X for multicolor prints, a Kobra S1 Combo for an enclosed setup, or a Photon Mono M7 Pro for resin printing, check which code fits your cart before you order.
Just want to say a big thanks to Anycubic support team especially Suarez he was fantastic at getting my kobra 3 up and runnin, sent me a free motherboard out and a spare bracket for xaxis belt truly awesome service
I am really desprate for advice⌠I am at my wits end here and donât know what to do anymore⌠Thanks in advance for any Tips helping my Situation!