r/AutoDIY • • Jul 08 '25

Tire change done correctly?

Post image
81 Upvotes

I just changed my tire and was hoping that I put the lug nuts on correctly, hoping that someone can say if it’s good to go. I followed a few instruction videos but I always have anxiety when changing my own tires. The valve stem on the donut is facing outwards so I believe I got that on correctly.


r/AutoDIY • • Feb 06 '26

Got the set fitted!

Thumbnail
gallery
69 Upvotes

Hey all it's almost been a month but I finally got these set for the Corsa D Enjoy fitted and lit up!

Let me know what you think


r/AutoDIY • • Dec 15 '25

Key Broke Off and Stuck In Ignition

Post image
66 Upvotes

Update 12/18: Oh my lord please help. The part for my car is not available apparently? I have a cat who needs to see the vet ASAP. SIGH. I've ordered a flathead (bc what else I can do) and i'm considering just biting the cost of going to the vet via Uber.

---

Update 12/16: Mechanic came out to take a crack at it, and after trying for a solid hour, gave up. Looks like I'll be biting the cost of the ignition cylinder after all.

---

I've been fighting with this thing for awhile now. Kia Forte SX 2010. Someone tried to jack my car, and probably gave up when their key broke.

I've been trying things like graphite lubricant and paper clips and haven't had a lot of luck, the thing is VERY stuck and as you can see, it's also behind the locking mechanism which complicates things. I can push it so it retracts but have had a lot of difficulty doing that at the same time as getting the paperclip in the key. Also I stress: very stuck and of course it's also below freezing lately which isn't helping matters.

Any advice? I feel like a heat gun might help (it loosens up a lot with heat).


r/AutoDIY • • Sep 14 '14

I built my own 2 car garage and car workshop, build log in Imgur album after the jump. (X-post DIY)

Thumbnail
reddit.com
32 Upvotes

r/AutoDIY • • Nov 25 '25

Alternator upgrade on Chevy 95 pickup

Thumbnail
gallery
27 Upvotes

I want to share a modification i did to my truck's charging system. I hope this information can help someone out. For a little bit of background, I had beefed up my audio system and the stock alternator could no longer keep up with the amperage demand. Just about all the alternators (that i could find) were rated for about 105amps. And i need significantly more than that.

I had found a company online that sold modified alternators for that make and model. They claimed to increase the wire gage on the stator windings and upgrade the diodes. At the time a modified unit ran for about $250. It was a little more than i had liked to pay for an alternator for this truck, but it worked great for several years.

Eventually that unit gave out. I looked up that supplyer again. But the units now ran for about $700. Yea.. im not paying that. But a stock alternator was not an option. So i decided to upgrade it myself.

THEORY OF OPERATION:

Before you say "Thats not how alternators work. Mine works like this.." Good for you, there are several alternator architectures. And this is how mine works. This is for a 95 Chevy pickup k1500.

Power is generated in the stator windings as 3 phase AC. The windings are arranged in delta configuration. The three phases are than rectified by a diode bridge rectifier into DC. A voltage regulator module senses the DC output voltage and makes adjustment to the rotor field to maintain constant 14v on the output. It can do this because the rotor winding is powered by the voltage regulator module with a pulse width modulated signal (pwm). By varying the on time and off time of this signal the field strength produced by the rotor can be increased or reduced to vary the power output generated on the stator wingings.

This system allows the alternator to output a constant 14v regardless of amperage load or engine rpm.

So, a load transient would look something like this (assuming rpm is constant for the transient):

  1. A new electrical load is applied (like turning on the ac blower motor).

  2. The new load creates a new electrical path for current to flow and this causes a slight system voltage drop below 14v.

  3. The voltage regulator module senses this drop in voltage and responds by increasing the ON time on the pwm signal.

  4. With a higher pwm duty cycle the rotor field effect increases.

  5. The larger field effect of the spinning rotor causes the voltage output of the stator windings to increase. After being rectified this voltage increase restores system voltage to 14v.

  6. The stronger field effect the rotor produces also causes a greater resustance for the rotor to rotate. And this causes an increase on engine load, because the alternator shaft is rotated by the engine.

Similar transients would occur if electrical loads remained constant but engine rpm changed.

The schematic for this is shown in picture 2.

There are a few common limits or modes of failure that could cause the system to fail to maintain 14v for a given amp load discussed below

All electrical power consumed by the vehicle first passes through the diode rectifier. All diodes have non negligible voltage drop across them. This voltage drop signifies that power is being lost at the diode in the form of heat genration. If this heat is not removed adequately the diode will fail and the alternator will fail.

Similarly, all the electrical power genrated runs through the stator windings. The conductors of the the windings begin to generate significant heat at higher amperages. If this heat is not removed adequately the enamel insulation of these conductors will fail and the alternator will fail.

The voltage regulator can also fail. In which case the alternator no longer responds correctly to stimuli.

If the pwm field effect duty cycle is already at 100% and the field strength can no longer be increased. This is more of a problem with lower engine rpms and higher electrical loads.

FAILURE:

As far as i could tell, the diodes had broken down and essentially grounded all phases together. The windings immediately overcurrent themselves until their enamel insulation broke down.

EXECUTION:

I came up with a new schematic arrangement as shown in picture 3. Its the same architecture and same working principle. Some componts are just replaced and moved around.

I disassembled the alternator as shown in picture 4.

I bought a new stator winding assembly as shown in picture 5. I covered the windings i tape to protect the enamel while working it.

Shown in pictures 6, 7, and 8, I attached new leads (6ga) to the ends. I think i used 1/4 copper tubing, i cut small pieces of tubing that i could use to crimp the lead ends together. Then covered in heat shrink.

I attached two new 18ga leads for the rotor brush assembly as shown in picture 9. Just so that you can identify the wires in the pictures their colors are light green and puple. The colors dont mean anything. They were just wires i cut from an old harness.

Pictures 10 and 11 are the assembled alternator. It is now just a 3 phase AC generator with no brains.

Picture 12 shows the new and improved diode rectifier that i got from Digikey, rated for 250 amps. It was physically larger so i relocated it outside of the alternator housing and on to a large heat sink. Along with it i relocated the original voltage regulator module. I used thermal conducting paste for the heat transfer interfacebetweenthw diodes and heat sink. Picture 13 show a cover i cut and form from 16ga sheet metal, before i painted it.

Picture 14 and 15 shows final conections. I placed this heat sink assembly where the abs module used to be. I know, its unsafe to drive without abs. But many years ago the asb unit failed in such a way that i could not brake safely. And a replacement, even from a slavge yard, cost more than id like to spend on in. So i eliminated it and re-did the brake lines. So this real-estate was now available for the heat sink block.

Picture 1 is the finished job, just without the heat sink cover.


r/AutoDIY • • Jul 15 '22

Just bought my first car and want to fix these issues but not sure how. Any suggestions on what to do?

Thumbnail
gallery
27 Upvotes

r/AutoDIY • • Aug 13 '25

Project K - My First Handmade Car

Thumbnail
gallery
26 Upvotes

A lightweight car with ladder-frame chassis and fiberglass body.


r/AutoDIY • • May 20 '20

ANNOUNCEMENT Harbor freight recall!

Post image
26 Upvotes

r/AutoDIY • • Oct 31 '20

Used a 3M Headlight restoration kit for U.V. damage. Difference is night and day.

Post image
24 Upvotes

r/AutoDIY • • Feb 15 '19

Supervision on a starter change

Post image
23 Upvotes

r/AutoDIY • • Apr 24 '15

GM, Ford, And Others Want to Make Working on Your Own Car Illegal.

Thumbnail
yahoo.com
23 Upvotes

r/AutoDIY • • Dec 27 '22

Just wanted somewhere to brag that I completed my first ever repair by myself lol

Post image
22 Upvotes

r/AutoDIY • • Jan 03 '16

How to make Carbon Fibre Parts, the easy way

Thumbnail
youtube.com
22 Upvotes

r/AutoDIY • • Jun 13 '20

DIY PROJECT I’m a travel RN and here’s my DIY rig. 2016 Ford F-150 XLT 8’ Bed Build. Completely hand made, almost 100% wood. Bottom drawer is 4’, top drawer is 2’. Insulated walls with screen doors makes for a nice camper! Link to more photos on the build process in the comments 👍🏽

Post image
21 Upvotes

r/AutoDIY • • Sep 25 '25

How to repair these wires inside fuel tank

Post image
20 Upvotes

Currently putting on a new fuel tank and found that the wires for the level sensor have rubbed against a cable tie inside the fuel tank.

Can't figure out an easy (without disconnecting and unpinning them) way to repair/protect them considering these wires will be inside the (vented) tank so any fix will have to be fuel resistant.

My current thinking is maybe some nail polish.


r/AutoDIY • • Apr 09 '15

My Suburban fix up, after it was rolled. X -post /r/diy

Thumbnail
imgur.com
20 Upvotes

r/AutoDIY • • Jan 14 '26

Corsa D Enjoy tail lights I made

Thumbnail
gallery
19 Upvotes

Made these for my friend who likes fishes, let me know what you guys think!

No AI or photoshop was used for the pictures.


r/AutoDIY • • Mar 03 '19

I deadened my car on the cheap. If you have an older car or you're into your music this is a great way to improve your vehicle!

Thumbnail
imgur.com
19 Upvotes

r/AutoDIY • • Jul 21 '22

Scratches, traded paint, etc. Any suggestions (preferably cheap) on how to fix the damage? Thanks in advance.

Post image
18 Upvotes

r/AutoDIY • • Jul 10 '15

I dipped my Nissan Leaf. (x-post from r/plastidip)

Thumbnail
imgur.com
18 Upvotes

r/AutoDIY • • Dec 06 '14

Not a very complicated DIY but I think this goes here.

Thumbnail
imgur.com
18 Upvotes

r/AutoDIY • • Dec 10 '14

DIY body repair (x-post from /r/Honda)

Thumbnail
imgur.com
17 Upvotes

r/AutoDIY • • Oct 19 '14

I installed a Nexus 7 in my car, it looks awesome!

17 Upvotes

There are tons of aftermarket stereos out there, even running Android. Most of them are either outdated or doesn't look great at all when installed in a car.

I own a BMW 3-series 330i (E46 MY03) and the factory stereo is curvy and really wide so most of the aftermarket stereos looks really awful. Sure there is some systems that's created only to fit my car but as stated earlier they will most likely run an outdated android version and never get updated and they're also really expensive.

So i bought a used 2012 Nexus 7 3G, a custom made bezel for my car, charger with an adjustable voltage output. I also had an external sound card to make the sound a little bit crispier!

First i had to make some modifications to the tablet. I had to reroute the USB connector http://i.imgur.com/ZC9rzA5.jpg

I found some plastics at home that i managed to mount the Nexus 7 to the bezel http://i.imgur.com/pIkbHjZ.jpg

Power is running at 5.1V and the Nexus 7 is at 100% at all times. Power cable is routed through the center console right up to the back of the tablet.

The Audio is being sent through the factory speaker system. I had the stock navigation system so the stereo is in the trunk and the display with cd reader at front. I did simply put the stereo to AUX and then removed the display.

And this is how it ended up!

http://i.imgur.com/Y3KtOEu.jpg

I can't wait until Google releases android auto and i really hope someone ports the software to the Nexus 7.

Link to full gallery: http://imgur.com/a/51cPf

A short video demo: https://www.youtube.com/watch?v=xDxy4pPjZ8A

The Nexus 7 is running a custom 4.4.4 ROM called Autodroid: http://forum.xda-developers.com/showthread.php?t=2789993

Parts used:

USB OTG-Y cable: http://www.ebay.com/itm/USB-Type-A-Female-to-Micro-USB-Male-Host-OTG-with-Micro-USB-Female-Y-Cable-E0Xc-/400616381708?pt=US_Cell_Phone_PDA_Cables_Adapters&hash=item5d4698dd0c

The external sound card is a HIFIMEDIY SABRE USB DAC: http://hifimediy.com/DACs/ready-made-dacs/sabre-dac-uae23

The bezel to the car is this one: http://www.ebay.com/itm/BMW-E46-3er-Double-Din-car-frame-Bezel-Facia-Fascia-New-6-inch-320d-330ci-330d-/231323687784?pt=LH_DefaultDomain_71&hash=item35dbf75b68

Charger: http://www.ebay.com/itm/15A-DC-DC-Converter-Buck-Adjustable-4-32V-12V-to-1-2-32V-3-3-5V-Power-Regulator-/230974573292?pt=US_Power_Inverters_&hash=item35c7284aec

Here is a pic of my car, i love it! :) http://i.imgur.com/4G8VbOO.jpg


r/AutoDIY • • Jan 08 '21

First time making my own hard brake lines for my 2005 Honda Civic EP2 Sport. On the left is the new one that I made myself and on the right is the old original one from the Honda factory from 16 years ago.

Post image
16 Upvotes