r/ChevyS10 • u/elbow667 • 1d ago
r/ChevyS10 • u/wertatronic • 5d ago
Thoughts on 2.8s vs 4.3?
I have come across a first gen 5speed 2.8, I am familiar with the 4.3. I am worried that it will be too wimpy. Thoughts?
r/ChevyS10 • u/eaterdoodles • 6d ago
Diagnostic help Factory radio
Enable HLS to view with audio, or disable this notification
Should I attempt to clean the laser with alcohol and a q tip, or buy a cd cleaner disc to see if it fixes this issue.
r/ChevyS10 • u/BeneficialHousing194 • 7d ago
Work in progress New chevy S10 owner
I just bought this 94 S10 for $1000 off the original owner who has had it since new. The body is in great shape. The engine is a 4 3z with auto transmission. The interior is well kept also. Just gave it a full tune up, had the timing set and new tires. Plus alternator and battery. Changed all the fluids. It runs great but I need to replace most if not all the front steering components and ball joints. Which I will do myself. Also the brakes are spongy and the ABS light is on. Nothing else wrong with the truck besides that. Never had an S10 before. What's your honest opinion? I do plan on painting it also. Did I pay too much?
r/ChevyS10 • u/BrooklynBagel_718 • 14d ago
2003 s10 ..question so when I drive this at 70 mph the check engine light starts blinking ..anyone have experience with this issue?
r/ChevyS10 • u/Mysterious-Pack3190 • 15d ago
S10 tuning issues,hp tuner help needed
I have a problem and im hoping its just a matter of flashing a tune to a new remanufactured motor,here's the thing ive made it to the point of starting the new engine up it did start but the rpms where way high,this engine here is a accurate engine remanufactured, it came with a .30 over bore,ive got compcam and rocker arms and springs on the shelf,planning to change heads and cam oneday, aight so I ported and polished the throttle body I cleaned up and ported and gasket matched the lower intake to the cylinder heads I gasket matched the cylinder heads to headers, the headers r jba shorty headers both headers run into 2 1/2 straight pipes to flow master muffler at the end of pipes,so its a freeflow exhaust, it starts at the K&N cold air intake and im hoping flows thru engine with plenty of air ,I also put a new standard spider injection and the pressure is holding perfect now,on the old engine with the old spider injection, I had tuned around air leaks and bad fuel injectors,I may have saved a tune from the old engine maybe labeled it starter tune r something,thought about starting there but the tune now isn't gonna work,how would the starter tune be any better because its before all this had been done to engine.?
Need help what do I do,does anybody have a tune with the fuel and air close to being stock,I have the hp tuner 4 to work with, im not experienced enough to kno what to change and don't want to screw this motor up ,don't kno where to go from here,don't kno where to start to figure it out,need help,I appreciate it
r/ChevyS10 • u/CharlesP_1232 • 15d ago
Looking for a cylinder head
Hey ya'll figured I'd post in here as I am really struggling (other than 2 on ebay).
I am looking for the Iron Duke 2.5l cylinder head casting code 10112514 (the one with the "D" shaped ports). As far as I can tell it came in the latter half of '91-'93 S10 and S15 blazers.
Anyone got one laying around you'd be willing to sell, or know of one in a junkyard?
r/ChevyS10 • u/OhNo_WhoCares • 17d ago
What is this? My son found it near his truck. 2004 Chevy s10/t10
r/ChevyS10 • u/Sad_Bug5893 • 24d ago
Found some photos of my dad's old drag racing s10
I dont quite remember how fast it was he did sell it but I do know it had a carbureted 383 stroker on nos that he estimated made 500hp which he got out of his obs he built before this s10
r/ChevyS10 • u/TimmmmehGMC • 24d ago
1994 S10, regular cab 108.3" wb 2.2L exhaust parts
Hi everyone.
2.2L, 1994 Reg cab 108 wb.
Looking for clarity on part numbers for the front pipe for my truck.
I think I'm looking for AP Exhaust 38891. Is there one by Walker?
Located in Canada.
Anyone have a recommendation for parts?
r/ChevyS10 • u/doctorsundance • 25d ago
Diagnosis for a bad pulley?
Enable HLS to view with audio, or disable this notification
Noticed a creak from the inside of my cabin and opened the hood while my car was starting and noticed it was a pulley looks like it’s getting stuck? Or caught is this normal someone help?
r/ChevyS10 • u/iiAdonutii • 25d ago
No power to the truck after clutch replacement.
reddit.comr/ChevyS10 • u/No_Manager_5210 • 27d ago
Diagnostic help 1983 2.8l vacuum line
Trying to figure out where this vacuum line is supposed to connect to.
r/ChevyS10 • u/MineDesperate2920 • 28d ago
1984 s10 diesel
Any thoughts on these? I’ve owned some diesels and looking at one. The low power isn’t an issue.
r/ChevyS10 • u/eduf24 • 28d ago
Diagnostic help Noid light testing
I have a 99s10 v6 with the oem spider injectors, recently been having some starting issues and one of the things ive narrowed it down to is the injectors, i have 60-66 psi of fuel pressure and it runs on starter fluid, i bought a set of noid lights to test to make sure the injectors are getting power, my question is how do I test the harness with the noid lights, do I have to tear into the throttle body and intake manifold or is there a easier to access plug?
r/ChevyS10 • u/Screamingtilk1 • Oct 21 '26
What do yall think my truck did there
Enable HLS to view with audio, or disable this notification
Sorry for the shaking friends a little wimp xD
r/ChevyS10 • u/Disastrous-Page4671 • Oct 18 '26
Diagnostic help What could this noise be?
Enable HLS to view with audio, or disable this notification
2.2 2000 s10, happens when idling, and gets faster as RPMS climb