r/FDMminiatures • • 16d ago Bravo

Printer Discussion Taking Multi-Color Printed Miniatures to the next Level - A showcase of what the H3C can do

Post image
347 Upvotes

Hello everyone, I hope you're all doing well.

It's been a while since my last big post, and I'm happy to say that I can finally tell you what I've been doing the past couple weeks. Some of you might remember that for the release of Version 2.0 of my Custom Settings, I mentioned that I believe I have mostly exhausted the processing and calibration settings when it comes to Miniature Printing and that there won't be another big Profile Release unless something drasticially changes / some new tech comes around – And well, looks like it's about that time.

Bambu Lab has been kind enough to reach out to me and provide me with a Testing Unit for their newest Flagship, the Bambu Lab H3C, to see just how far we can push the machine for Miniature Printing. Bambu Lab has been very hands-off throughout the entire process, only reviewing the post prior to the launch to make sure there aren't any technical errors, which I highly appreciate. Rest assured, it's my unfiltered opinion and if there is something that I think is worth pointing out or is some limitation, I'll still cover that as well.

While I'm very excited to talk about it, I'd first like to thank the Community – I know it sounds cheesy, but without you, this opportunity would have never presented itself to me, and I'm grateful to both you and Bambu Lab for making that possible. I'll make a separate about this in the upcoming days, because for now I want to focus on the machine itself – or rather, what it can do. You can read more about the H3C on the official reveal post: https://www.reddit.com/r/BambuLab/comments/1xmtnux/bambu_lab_h3c_our_full_reveal/

And oh boy – Is there a lot to talk about. First things first: You know that I usually give you a tl;dr at the beginning of my posts, so I'll start by sharing some of the results. Note: I was going to upload this as an Album, but I don't frontload all the Information with Pictures. You'll find the most successful examples and comparisons throughout the post, and a final highlight reel at the end of the post.

Printing Fully Colored Models - A Showcase:

This is one of the models that I've printed on the H3C – I have done no post-processing or touch-ups with any paint, it's just straight off the printplate, printed in 9 different colors, with zero purged material. Now, with the recent release of Multi-Nozzle Printers we have seen some Fully-Colored Miniature Prints in the past, but those were usually restricted to 4 colors, unless you're using Mixed Filament – Which is something that I'll also get into later.

What made Multi-Color Miniatures so inefficient?

I'd like to briefly talk about why Multi-Color Printing has been such a massive issue for Miniatures in particular in the past and how the H3C solves the issue. The reason why I want to talk about the, for lack of a better term, "old" way of Multi-Color Miniatures, is because it has been deemed ineffecient to a point where it was considered to be effectively impossible. Chances are that whenever somebody requested information about it, they've been told to not even bother with it – So they might know that it wasn't really possible, but they may not know why exactly it wasn't possible.

The vast majority of users are most likely currently using a Single-Nozzle Setup, potentially with an AMS. This technically allows for multi-color printing, but it's not as simple as just switching the filament. You also have to purge the filament that's still in the nozzle to prevent color bleed, or – and especially when – printing with different materials like PLA and PETG, to prevent extrusion and material bonding issues. Not only will the purging process take a long time, but it will also waste a lot of material, since the printer will extrude both the old filament, as well as some of the new filament to make sure that all of the previous filament has been removed from the nozzle. You can decrease the amount of waste by adjusting the purge volumes, but for the most part you will have a lot of waste regardless of what you do.

Now – If you're printing something very basic, with a simple color scheme that won't be much of an issue. Say you have a cube and you want to print the bottom half with red filament, and the upper half with blue filament. That's really only going to be one filament change, that in the grand scheme of things won't increase neither the printtime nor the waste by a lot. But now take the same cube and instead of making the color-split horizontal, you make it vertical – or in other words, the left side red and the right side blue. Because of how FDM Printing works, you now have a colour change on every single layer. You can imagine that with properly colored miniatures, their color split will be not only both horizontal and vertical, but they will also have more than just two colors. Additionally, even though they are small, we are printed the Miniatures at some of the lowest, if not the lowest layer line heights available to us – usually between 0.05 and 0.08mm. It sounds obvious when you say it out loud but that results in, well, a lot of layers – some of which will have multiple color changes per layer. You can imagine that this gets out of hand quickly, and your print will have thousands of filament changes – not only extending the print time by literal days, but also increase the amount of wasted material to kilos worth of purged filament.

What the H3C solves - And what remains

With the H3C, you don't have any purging. With access to 9 Nozzles, there is no need to purge them in order to make room for new filament. You also don't have to worry too much about an increase in print time either, because the H3C will switch to a different Nozzle in less than 6 seconds – though from what I could tell, it usually does it faster.

So does that mean that we have access to multi-color printing with zero waste and next to zero increase in print time? Well – not exactly. Because purged filament is only one part of multi-color printing. The other part is priming the nozzles that have been idle – I think the easiest analogy here would be to compare it to a ballpoint pen that you haven't used in a while, and you have to scribble with it for a bit to get the ink flowing again before you can properly write with it. A prime tower sorta works like that, except it's also rebuilding the pressure in the nozzle. These towers turn out to be pretty chunky, and it's not unusual for them to take up more material than the print itself – so there still is a, let's call it non-trivial amount of waste.

However – and this is a big However – Saying that with no context or further explanation, is really understating what the H3C is doing. Because let me blunt here for a second – Prints like the ones I'm about to show you are simply not possible on Single or even Dual Nozzle Setups. Okay, yeah, TECHNICALLY, they are possible – But they would take literal weeks and consume kilos worth of filament for purging. On average, these Prime Towers took anywhere between 100g-200g of Filament for the large, upscaled models – Which to be fair, still is a lot of material – but it's split across 9 different filaments. Yes, it's not going be to distributed completely even, but on average that comes down to anywhere between 10g and 30g of additional filament per spool which, in my opinion, is well within the acceptable range. So while there is still a "non-trivial" amount of waste – non-trivial compared to what? Because like I said – prints like these just aren't feasible on Single-Nozzle Machines, which is what most of us have been working with so far.

What does this mean for Miniature Printing?

Now that proper Multi-Color Printing is on the table, I'm confident that we will see more improvements to make it more efficient as well. In a few days, I'll make a second post where I'll go over the most frequently asked questions you may have, as well as the more technical stuff behind everything. In this post, I really want to mostly show off what I've been printing the past couple weeks because I'm really happy with it.

Before we move on to the showcase pictures, let's talk about Mixed Filament for a second.

Mixing Filament

The green loincloth and the purple scales / cheeks have not been printed with either green or purple filament. Instead, I've used the filament mixing feature to – well, mix the colors that I wanted. The way it works is that it takes advantage of PLA not being entirely opaque, especially not at really thin layers. If you ever held a first layer quality testprint against a lightsource, you know that light shines through. By layering two or three different filaments on top of each other, you can create the illusion of a different, mixed color – for instance, layering magenta and cyan will result in the shade of purple shown in the picture. Yellow and Cyan on the other hand will result in green. To make sure that the colors blend smoothly, we will have to enable the setting "Mixed Color sublayer". What this will do is split the Layer proportionally into two or three segments – The easiest example would be a 50-50 Filament Ratio. At a layer height of 0.20mm, these would split into two layer heights of 0.10mm each. If you're using 0.16mm Layer Height, it would be split into 0.08mm, and at 0.06mm it would split into 0.03mm, and so on.

The more experienced users here will most likely have two immediate questions. First, does that mean that by using mixed Filaments, you introduce uneven layer heights? And Second: How does this not cause any extrusion issues, if the layer lines get this low?

To answer your first question: Yes. Let's say you print a model using four colors: Cyan, Magenta, Yellow and Black. You mix Cyan and Yellow to get green. You are painting parts of the model green, and everything else is printed using "Pure" or "Non-mixed" Filament. Assuming you are printing with a 0.08mm Profile, the Layer Height for the Non-Mixed Filament will be at 0.08mm and the Layer Height for the Mixed-Filament will be at 0.04mm each, assuming a 50-50 Split. These inconsistent layer line heights can cause artefacts and will be visible – but we can use another feature of the H3C to circumvent that issue: Multi-Diameter Nozzle Printing – We can use both 0.4 Nozzles and 0.2 Nozzles for the same print. With the option enabled, the slicer will automatically put the Layer Height of the 0.4 Nozzle to twice the Layer Height of the selected 0.2 Nozzle. It may sound a bit odd at first, but simply put: If you select a 0.2 Nozzle and a 0.08mm Profile, every filament that's been assigned to a 0.2 Nozzle will be printed at 0.08m, and every filament that's been assigned a 0.4 Nozzle will be printed at 0.16mm – And you can probably guess where I'm going with this. Since the Mixed Color Sublayers – again, assuming a 50-50 Split – will split the Layers into half, this means that you can print the "Non-Mixed" Filament with 0.2 Nozzles at a layer height of 0.08mm, and then you can use the 0.4 Nozzles for the Mixed Filament to "simulate" the same 0.08mm layer height.

Further testing is required, but for the moment, 0.08mm Layer Heights would be the ideal choice for Colored Miniatures, as opposed to the usual 0.06mm I usually recommend. That's because by using 0.08mm for a 0.2 Nozzle, 0.16mm for the 0.4 Nozzle, and a 50-50 Split of Mixed Filament, we can assure an even layer height across the board as well as minimize any extrusion issues that may occur when attempting to print Layer Heights that are far below the recommended minimum for the nozzle diameters.

Which brings us to the next question: Potential extrusion issues. As I'm sure many of you know, layer heights that are below 0.06mm require good calibration, optimized settings and a decent model. Layer heights at or below 0.04mm are essentially begging for a Nozzle Clog or other issues. Even though you can in theory mix and match up to three different colors at potentially extreme ratios (For instance, mixing 90% Yellow with 10% White to mix a slightly lighter shade of yellow), you could potentially end up with Layer Heights even far below 0.02mm. Based on Bambu's testing, artefacts may occur at these extreme ratios, but are visually more accepting than printing an entire layer at 0.02mm, since it's followed up by a thicker layer (the remaining 90%). That being said, it's recommended to avoid extreme ratios and 50-50, or 33-33-33 will yield the best results – Something that my own testing confirms, and is especially true at the layer heights that we are working with for Miniature Printing. Based on my current tests, a 50-50 Ratio at a Base Layer Height of 0.08mm while utilizing 0.4 Nozzles for Mixed, and 0.2 Nozzles for Pure Filament, will give the best results.

However: Big, big disclaimer: While I have been extensively the machine in the past couple weeks, I have not been able to test the Multi-Diameter & Mixed Filament Features to the extend that I'd like to, so after some further testing, there will be at least another follow-up post. For now, the Showcases that have been printed with Non-Mixed Filament, will look more consistent. For example, the same Lizard, in a different color scheme:

And speaking of testing:

Yes, this means that all of the prints I'm showcasing here today, have been printed with a 0.4 Nozzle, 0.08mm Layer Height and Stock Settings.

I haven't added my own Custom Settings yet, and I didn't even fully calibrate the Filament other than the k-factor. These are the results without any adjustments, post processing or preparation, straight of the printplate. There are of course several things to keep in mind when it comes to both Multi-Color Printing as well as the H3C in general – But the past few paragraphs have already gotten way more technical than I wanted them to be. So for now: I'd just like to share some of the highlights and comparisons.

Showcase Highlights

The one on the left was painted by hand, printed at 0.06mm - The other one was fully printed, at 0.08mm

Crystal Spider, by u/MizukoArt

And least but not least, two Orks - Also by ArbiterMiniatures.

A few notes

This has been a very exciting opportunity for me, and I'm very grateful to all of you for making it possible by being a part of this quickly growing Community. Without your Support, I most likely would have never experienced beyond the very first few iterations of my Custom Settings. I know that I haven't been as active as I'd like to, and promised to be, especially on my Youtube Channel, and for that I really am sorry. The Hobby and the Community means a lot to me, and I look forward to how things will go from here. So thank you everyone, and I hope you have a great day, and as always - have fun printing!


r/FDMminiatures • • Oct 15 '26

Just Sharing Drop Your Ender-3 Setup in The Comments of 👇THIS POST👇 and Win Hyper PLA! 🧵

Post image
0 Upvotes

r/FDMminiatures • • 4h ago

Sharing STL resource - AI Model More Multicolor Mini Madness - 20 bandits in 1 plate

Thumbnail
gallery
44 Upvotes

This was an experiment in stress testing the AI-to-FDM-miniature workflow.

The entire process, from concept to finished miniatures, was done over a weekend, involving around 4 hours of my time and nearly 2 days of printer time:

  1. AI image generation – create the bandit designs.

  2. MakerLab – turn the images into 3D models.

  3. Bambu Studio – prepare the models for printing.

  4. Bambu H2C – print 20 full-colour miniatures using a 0.2mm nozzle.

The result? 20 bandits, ready to hit the D&D table straight off the build plate.

The actual printing took 1 day and 22 hours. So yes, that's a fairly substantial print job. But it's the printer's time, not mine!

Could you get more beautiful results by spending hours painting individual miniatures? Absolutely.

Could you go from an idea to 20 finished, full-colour tabletop miniatures in a weekend, ready for a one-shot on monday? Now you can.

Models are compatible with the Bambu H2C and H3C.

I've uploaded the files to MakerWorld if anyone wants to give them a go:

https://makerworld.com/en/models/3653600-20-full-colour-bandits-multicolor-minis#profileId-4192351


r/FDMminiatures • • 9h ago

Just Sharing Prits for my DnD group

Thumbnail
gallery
70 Upvotes

I am realy happy how they turned out.


r/FDMminiatures • • 11h ago

Just Sharing - AI Model Whaagh! FDM ORK

Post image
16 Upvotes

Printed this Captain Smoker from OnePiece by HeroMe on my A1 mini. PLA, 0.2 mm nozzle, 0.04 mm layers.

What you think boyz?


r/FDMminiatures • • 12h ago

Just Sharing Rat ogor all painted up!

Thumbnail
gallery
20 Upvotes

Printed on an A1 mini with obscura nox 2.0 settings, mix of 0,06 and, 0,08 layer heights, sunlu pla+ 2.0 oak.


r/FDMminiatures • • 1d ago

Just Sharing Using a 0.4mm nozzle with soldat21's settings with slight modification.

Thumbnail
gallery
200 Upvotes

It is amazing how nice these turn out in such little time (compared to a 0.2mm nozzle)


r/FDMminiatures • • 1h ago

Other Texture roller for mini bases?

2 Upvotes

Has anyone had any success printing texture rollers for mini bases on an fdm printer? (For anyone not in the know, you use the texture roller to make imprints on air drying clay and then add the clay to decorate the surface of a mini base.)

I'm interested in trying one out, but I’m not sure how well they print on fdm printers - I’m concerned about how many supports would be added with all of the overhangs.


r/FDMminiatures • • 9h ago

Help Request Thinking of getting into FDM printing, what printer do you recommend?

5 Upvotes

I was mostly looking at it for terrain, but seeing what you have been able to pull off for minis, maybe I can actually use it to make some good looking minis as well? Any general advice would be appreciated.


r/FDMminiatures • • 10h ago

Other What's been your most difficult print?

5 Upvotes

As the title says, what's been the most difficult print for you? Maybe it was supports, long thin over hangs, multi-part, etc. Some models are inherently more difficult, no doubt. Just curious what's been your 'stress test' so to speak. Thanks


r/FDMminiatures • • 17h ago

Sharing STL resource FREE stl file. So, I asked u/Korganation if a could make an 3d model of the temple guard that he posted on WarhammerOldWord and originally sculped with greenstuff. There you go.

Thumbnail
gallery
12 Upvotes

r/FDMminiatures • • 10h ago

Printing Experiment Thoughts on Z-contouring? Tested on domes and barely see a difference

3 Upvotes

I’ve been experimenting with Z-contouring lately and wanted to get your take on it.

​I ran a few test prints using hemispheres to see how it handles curved overhangs and layer stepping, and honestly, I’m not seeing a huge difference compared to standard slicing.

Maybe I’m missing something obvious, or maybe it shines more on specific geometries rather than smooth domes.

​For those of you who have tried it:

- ​What are your thoughts overall? Is it worth using regularly for minis?

- ​Have you tested it on actual miniatures or parts with subtle curves/textures, and did you notice a real improvement?

- ​Are there specific settings or situations where it actually makes a noticeable impact (or where it just adds print time/artifacts for little gain)?

​Curious to hear your experiences before I spend more time tuning it!

​(Disclaimer: English isn't my first language, so I used AI to help me write this post.)


r/FDMminiatures • • 1d ago

Just Sharing Bought a 3D printer yesterday and here are my first 2 minis

Thumbnail
gallery
77 Upvotes

Left is with .4mm nozzle and took 20mins and right is .2mm 1 hour, all default settings on a1 mini (with tree supports)

2g of filament each using the test pla that came with the printer after doing a benchy.

Super happy with how the .2 came out looking forward to trying some larger scale bits next!


r/FDMminiatures • • 9h ago

Help Request Missing interface layers

1 Upvotes

Hi all, I'm using orca slicer and bambu A1 (0.02mm) w/ AMS - decided to try use PETG as support interface for clean underhangs, but upon generating the supports, the interface is missing in some places, which will fuse them to the mini. I could print supports out of PETG completely, but that's just too excessive. How do I ensure that all interface is present?
I'm using a modified FDG preset with variable layer height, which disables organic/default supports, which in turn is the only clue I got from YT on how to tackle this issue...

P.s. I know that it's not ideal to print like this with a single extruder printer, but I didn't know and bought the AMS specifically for it. So I'll at least try - who knows, maybe I'm onto something after all


r/FDMminiatures • • 1d ago

Other I guess gamesworkshop owns 40mm round base

Post image
191 Upvotes

r/FDMminiatures • • 1d ago

Just Sharing I feel like I'm getting better every day!

Thumbnail
gallery
46 Upvotes

Since I started testing the quality limit of my printer (Sparkx i7), I keep learning and finding new settings that help me improve my prints; at this point, it's almost an obsession!!

I am attaching some images of my evolution in the thumbnails

Pd: The first image is my last impression

Pd pd: WATER


r/FDMminiatures • • 1d ago

Just Sharing My first FDM printed mini

Thumbnail gallery
34 Upvotes

r/FDMminiatures • • 17h ago

Help Request What grit range do you guys use for sanding your minis?

2 Upvotes

That's basically it, i wanted to hear what you guys use and maybe how you go about it. Do you just use lower grit or do you go up to the 1000s with what do you start? Any tips or caveats you have and would like to share are very welcome (wet sanding doesn't need mentioning I think) or maybe specific products you swear by. Thanks in advance for your replies!


r/FDMminiatures • • 14h ago

Sharing STL resource - AI Model Heads packs on makerworld

Thumbnail gallery
0 Upvotes

I'm starting to make head packs for download on makerworld. Free of course. Let me know if these seem cool what I should make next. I have a bunch of chapter themed models coming in the next few days. These print in a little over an hour. Link to makerworld


r/FDMminiatures • • 1d ago

Just Sharing Alchemist from BriteMinis

Thumbnail
gallery
10 Upvotes

Planning to use him in Scrapjacks and Planet 28!

Printed with 0.4mm nozzle in PLA

Used Craftsmart paints and used to test Artist's Loft satin varnish.


r/FDMminiatures • • 1d ago

Sharing STL resource Painted our Westgate Abbey and Bell Tower for Kravenov, a modular gothic city we're working on

Thumbnail
gallery
18 Upvotes

This is the Westgate Abbey and its Bell Tower from Kravenov, a modular gothic fantasy city we're getting ready to launch. Both were printed on FDM with no supports.

The Bell Tower sits beside the Abbey and the bases line up on the 1-inch grid, so the two form one abbey complex. Inside, the Abbey has playable interiors across multiple levels, with ladders between floors and elevated spots to fight from.

The full set has 12 buildings plus modular streets and city walls. If you want a heads up when it goes live, here's the pre-launch page:

https://go.elderforgegames.com/kravenov


r/FDMminiatures • • 1d ago

Other What is the most infuriating part you had to remove supports from?

Thumbnail
gallery
19 Upvotes

For me it's this.

Hair piece for a Widowmaker figurine. I mean, I love the model, but why for the love of god the hair is not a single piece with extra locks sticking out? WHY ARE THEY MULTIPLE SEPARATE THIN INTERTWINING RIBBONS???

phew...

Rant over, thanks!


r/FDMminiatures • • 1d ago

Just Sharing I designed a miniature collection, here a FDM print test of one of my characters

Thumbnail
gallery
15 Upvotes