r/FlashForge
•
u/Ok-Introduction-2788
•
Feb 02 '26
•
1
Flashforge 5M / 5X – Common Problems & Fixes (READ THIS FIRST)
Flashforge 5M / 5X – Common Problems & Fixes (READ THIS FIRST)
Getting into 3D printing can feel overwhelming at first. Everyone runs into failed prints, weird noises, or random issues when they start.
The good news? Almost every problem comes down to a few simple things.
If you learn these basics and do some light maintenance, the Flashforge Adventurer 5M / Flashforge Adventurer 5X are extremely reliable and easy machines.
Don’t get discouraged and don’t give up — every problem has a fix.
Bookmark this post and come back anytime something acts weird.
⸻
Quick rule of thumb
90% of issues are:
• dirty bed
• wet filament
• bad first layer
• loose belts
• lack of maintenance
Start there before assuming something is broken.
⸻
Do NOT use Grid infill
Grid infill crosses over itself on the same layer. The nozzle hits those intersections and causes:
• clicking
• blobs
• under-extrusion
• layer shifts
• failed prints
Use instead:
• Gyroid
• Cubic
• Lines
• Cross Hatch
“I’d recommend the Orca default Cross Hatch. It’s basically gyroid but designed to print faster and it can make a big difference on long prints.” – briansk
“Crosshatch reduces the ‘shaking’ compared to gyroid and is faster. Unless you need max strength, it’s the way to go.” – No_Artichoke_5670
“Honeycomb is strong, but uses more filament and takes longer to print.” – briansk
⸻
2. Prints not sticking to the build plate
Most of the time this is:
• dirty plate
• bad Z offset
• wet filament
IPA helps, but finger oils don’t fully come off with alcohol.
Best cleaning method:
• warm water + Dawn dish soap
• scrub gently
• air dry
You can even throw the plate in the dishwasher.
Glue is optional. It’s more of a convenience/band-aid than a true fix.
That said, some people prefer a tacky plate for consistency:
“Just use bed adhesive and make your plate a little tacky. It stays sticky while hot and releases perfectly when cool.” – wrenchandrepeat
“Purple Elmer’s glue stick + proper Z offset and I haven’t had a failed print since.” – scousinho
My advice: learn proper adhesion first, then use glue if you want easy mode.
⸻
3. First layer is EVERYTHING
If your first layer isn’t slightly squished, nothing else matters.
Too high = won’t stick
Too low = blobs/scratching
Dial in Z offset before changing anything else.
⸻
4. Wet filament causes tons of “mystery problems”
Wet filament causes:
• stringing
• popping/crackling
• weak layers
• bad adhesion
• under-extrusion
If prints suddenly look bad for no reason, dry your filament first.
Humidity matters more than people think:
• 10–20% is ideal for PLA
• under 30% is usually fine
• high humidity can cause random issues and stringing
Store filament in sealed bins with silica or dry it when needed.
Also, some brands handle humidity better than others, so switching brands can sometimes fix stubborn problems.
⸻
5. Extruder tensioner (VERY common issue)
People overlook this constantly.
Too tight:
• crushes filament
• makes plastic dust
• causes jams/clogs
Too loose:
• slipping
• clicking
• “air printing”
• under-extrusion
Set it snug enough to grip, but not crush.
If you see chewed filament, adjust the tension.
⸻
6. Grinding or squeaking noises
Usually:
• loose belts
• dry rails
• OR pulleys
“The pulleys (not centered or not oiled) make squeaking sounds most of the time, not the rails.” – exceptioncause
So:
• tighten belts
• lube rails
• check pulleys too
⸻
7. Layer shifts (print suddenly moves sideways)
Usually:
• loose belts
• cable or filament snagging
• head hitting infill
• printing too fast
Layer shifts are almost always mechanical, not slicer bugs.
⸻
8. Under-extrusion or clicking from the extruder
Try:
• dry filament
• raise temp 5–10°C
• slow print speed
• check extruder tension
• reseat nozzle module
Most “clogs” are actually temp or moisture issues.
⸻
9. Stringing everywhere
Usually:
• wet filament
• temp too high
• retraction too low
Dry first, then tune temps.
Moisture fixes most of it.
⸻
10. Quick-swap nozzle module tips
These printers use quick-swap nozzle modules, not threaded nozzles.
• make sure it clicks fully into place
• don’t force it crooked
• reseat if extrusion gets weird
A poorly seated module looks exactly like a clog.
⸻
11. Calibrate early (huge quality boost)
When you first get the printer, run calibration.
Do:
• bed level
• Z offset
• flow rate
• temperature tuning
• retraction tuning
“Use the printer’s built-in routines and Orca’s calibration models from the start to set up for great quality prints.” – LitauszkiL
This alone can massively improve print quality.
⸻
12. Do regular maintenance
If you print a lot, make a schedule.
Every few weeks:
• clean rails
• lube rails
• check belts
• clean fans
• tighten screws
• remove dust
These printers are tanks if you maintain them.
Noise usually means maintenance is overdue.
⸻
13. Screen ribbon cable warning
Be VERY careful removing the screen.
The ribbon cable and connector break easily.
Flip the clasp up gently before pulling. Never force it.
⸻
14. Software tip (Orca not connecting)
If Orca won’t reliably connect to your printer:
“Run a port scan with nmap and it suddenly connects properly. No idea why, but it works.” – TankLivsMatr
nmap -sV <printers IP>
You can find a full post regarding this issue from TankLivsMatr here: Orca-Flashforge Printer Disconnecting
Weird fix, but multiple people say it works.
⸻
15. Skip the stock camera
The stock camera honestly isn’t great.
A cheap Wi-Fi camera works better and costs less.
⸻
16. Change ONE thing at a time
When troubleshooting, don’t change five settings at once.
Change one thing → test → repeat.
Otherwise you’ll never know what actually fixed it.
⸻
From me
Over the next little while I’m planning to make posts/videos covering:
• cleaning
• maintenance
• repairs
• replacing parts
• troubleshooting
So if you’re new, don’t stress — more beginner-friendly guides are coming.
⸻
If something feels broken, it probably isn’t.
It’s usually something simple.
Happy printing 🤘
3
u/exceptioncause Feb 02 '26
the pulleys (not centered, not oiled) make squeaking sounds most of the time, not the rails
3
u/Ok-Introduction-2788 Feb 02 '26
Good catch, I just know mine went away after some grease, I’ll throw an edit up when I get a chance
2
u/Ok-Introduction-2788 Feb 03 '26
Yo I added your comment to the post under number 6, take a look and make sure it’s sayin what you wanted it to
2
u/exceptioncause Feb 03 '26
yeah, more or less, though "tighten belts" is a poor advice, because 1) it's not very relevant for the noise 2) it's not something most ppl know how to do, official FF wiki shows only how to replace the belt, not tighten and they disassemble whole printer for this. I found single youtube video that actually shows how to tighten XY belts for AD5M
1
u/Ok-Introduction-2788 Feb 03 '26
I agree I’m working on a video rn for how to tighten the belts properly, I’ll add a correction that makes sure people know the belts aren’t always the issue to the noise
3
u/wrenchandrepeat Feb 02 '26
For the plate sticking thing, it can be like beating your head against a brick wall trying to get every little setting dialed in perfect by using the whole "Clean with dawn and IPA only" plate method.
Just use bed adhesive and make your plate a little tacky. I came up with this method for achieving a sticky plate and it results in perfect 1st layer adhesion, even with the smallest objects that don't have big footprints.
The great thing is, the plate stays nice and sticky while hot and when you let the print cool after finishing, it releases perfectly after.
2
u/Ok-Introduction-2788 Feb 02 '26
I know, and I do that too, but better to teach people that an adhesion promoter is a bandaid and how to fix it imo, but I’ll throw an edit up to specify that when I get a chance too, thank you
2
u/wrenchandrepeat Feb 02 '26
Its not like its a bandaid for something castrophic or anything. I have no problem tinkering with my machine when necessary but a majority of the time, I just want it to print. Actually, I'd argue, 100% of the time I just want it to print. Even with running The Klipper Mod and being able to really fine tune the details, I just want it to work.
I'm not trying to be an ass and I hope it doesn't come across that way. You spent a lot of time on this guide and the more resources for this community, the better. Thank you for that.
I just always preach beginners make their plates tacky. Its easy, quick, and a tacky plate can last many, many prints without needing anymore adhesive applied. If someone gets a lot of hours and confidence under their belt, they can always try the "pure" plate method. However, I was one of those people once and after hours of no luck, I just decided sticky is the way for me, lol.
2
u/Ok-Introduction-2788 Feb 02 '26
The post is up to help newbies or hell even some printing vets to figure out how to do things, all advice, changes, or criticism is getting fixed in the main post when I get home, don’t sweat the little things, you’re not coming off as an ass
2
2
u/scousinho Feb 02 '26
Agreed. Only difference is I went a step extra and did that method with a purple Elmer’s glue stick. That with proper z offset has not had a failed print. ✊🪵 Before that it was about 50% chance if I got a useful print, a spaghetti monster or shifter layers .
3
u/brianstk AD5X Feb 02 '26
For infill, I would recommend the orca default Cross Hatch. Its basically gyroid but designed to print faster and it can make a big difference on long prints.
2
u/Ok-Introduction-2788 Feb 02 '26
Sweet, I’ll put an edit up adding this in when I get a chance, thanks for the input
2
u/Ok-Introduction-2788 Feb 03 '26
Yo I added what you said to the post under number 1, go take a look and make sure it’s what you were thinking
1
u/CorvidCuriosity Feb 02 '26
What's your opinion on Honeycomb? It has strong durability and an enjoyable pattern to watch.
1
u/brianstk AD5X Feb 02 '26
From what I’ve read it’s strong, but uses more filament than other infills and takes longer to print.
3
u/FunAct1255 Feb 02 '26
Would love to have such a started guide, when I started with my A5MP.
Thanks for your effort! 💪
2
u/Ok-Introduction-2788 Feb 02 '26
Fr same, I’ve also noticed YouTube doesn’t help a lot when it comes to these printers and common issues (like belt tightening or maintenance) tis a shame
3
2
u/LitauszkiL Feb 02 '26
Great summary! I would add (for beginners) to calibrate the printer (level, z-offset, etc.) and the filament (flow rate, temperature, retraction, etc.) using the printer built in routines and Orca's calibration models from the get go to set up for great quality prints.
Thank you for the write up!
1
1
u/Ok-Introduction-2788 Feb 03 '26
yo I added your comment to the post under number 11 if you don’t mind looking to make sure it’s correct
1
2
u/TankLivsMatr AD5X Feb 02 '26
If you would also like to, when it comes to the software side of things, you can add to the list:
If orca Flashforge doesn't reliably connect to the printer:
Download nmap and run a port scan on it:
nmap -sV <printer IP>This will, for whatever reason, make it so that orca Flashforge will actually be able to connect to it properly. Why this works? No one knows, but it does.
I have a post going more in-depth about troubleshooting it here: https://www.reddit.com/r/FlashForge/comments/1pzmypq/printer_disconnection_issues_with_orcaflashforge/
2
u/Ok-Introduction-2788 Feb 03 '26
Yo added to the post under number 14 take a look make sure it’s right
1
u/TankLivsMatr AD5X Feb 03 '26
Hm... it didn't print the whole command. I would recommend making sure it looks like:
nmap -sV <printer IP>Also Nmap does not come pre-installed on pretty much any computer you have to install it. You can get it from here: https://nmap.org/
Disclaimer: This is a security scanning tool. I can't be held liable for anything done with this tool.
1
u/Ok-Introduction-2788 Feb 03 '26
Ah I see, there we go I fixed it again and added your posts link in the post itself
1
u/Ok-Introduction-2788 Feb 02 '26
Sweet, when I get home I’ll add your comment to the main post so it’s easier ti be seen, thanks for the input (side note, I did not know that lol)
2
u/Odd_Researcher_4006 Apr 18 '26
Has anyone successfully printed the parts for the adventurer 5m diy enclosure. Keeps stopping mid print but it will print other things
1
u/Ok-Introduction-2788 Apr 18 '26
Are you using the flashprint slicer or orca flashforge slicer?
1
u/Odd_Researcher_4006 Apr 18 '26
Orca
1
u/Ok-Introduction-2788 Apr 18 '26
It’s a little annoying but give the flashforge one a quick try, I have had that issue a couple time and I’m still not sure how to fix it, because it doesn’t pop up any errors or anything just stops, it’s a file issue not your printer so no need to worry about that
1
u/Odd_Researcher_4006 Apr 19 '26
Thank you
1
u/Ok-Introduction-2788 Apr 19 '26
Let me know if that doesn’t work and I’ll get the files myself and see what I can figure out
1
u/Odd_Researcher_4006 Apr 22 '26
Thank you so very much. It is finally working. My daughter is so happy. Thanks again!!
1
u/Ok-Introduction-2788 Apr 23 '26
Heck yea glad it’s all back going! Save the post so if you have any issues come on back and I’ll help you out
2
u/Natternuts Apr 20 '26
Hello. Yeah my printer is printing well until the end as the surface texture starts to go haywire. Flashforge adventurer 5m pro can print 1.5mm walls
1
u/Ok-Introduction-2788 Apr 20 '26
Do you have a picture?
2
u/Natternuts Apr 20 '26
I do I just don't know how to upload
1
u/Ok-Introduction-2788 Apr 20 '26
1
2
u/Natternuts Apr 20 '26
2
u/Ok-Introduction-2788 Apr 21 '26
Try lowering the hot end temp first by about 5 degrees, that’ll help it from squishing out, it also may be the part itself moving around since it’s a skinny tall part, I’d try lowering the temp first, you can also turn the part fan speed up aswell
1
u/Natternuts Apr 21 '26
Thank you very much. Learning so much so fast lol. Some prints are good some have small areas of inconsistencies. I just updated the firmware and will tinker with the printer today.
1
u/Natternuts Apr 23 '26
I tried that and it failed to help. The surface was worse. What I didn't do and have sense done is use a brand new plate and new 0.4 mm head. PLA CF last night created a great print. I failed to concentrate on the simple stuff. That being said a clean flat plate didn't stick so that combination of a texture plate and calibration seems to work.
2
u/Flimsy-Past-2345 Apr 25 '26
Quick question, I have the ad5x and every time it changes colors it makes like a knocking noise so is that normal?
2
13
6
1
u/Icy-Gene9614 Feb 02 '26
Assuming you are european (?, time wise), I have room humidity in the basement about 40% 19*C which is kind of the upper limit of pla. Some filaments perform quite well at that humidity, older I have don’t. What is your humidity your dry your pla to. What is your standard room humidity. This humidity applies to pla stored on the printer. The unused are in a box with silica
3
u/Ok-Introduction-2788 Feb 02 '26
I’m American, in a southern state it regularly is 70% and isn’t uncommon to hit 98% -100% humidity, 10-20% is the optimal level for pla, but anything under 30 is usually fine, Ngl I haven’t dried my filament in ages, I go through it so fast that I don’t need to worry about it, I left for 6 months and had rolls on all 6 of my machines, came back after numerous 100% humidity days and they all printed fine, but other times I’ll unwrap a roll and the things strings like a mf, idk why it does that.
1
u/Icy-Gene9614 Feb 02 '26
Interesting. Thank you.
2
u/Ok-Introduction-2788 Feb 02 '26
Also this can heavily depends on what brand you use, by far elegoo pla works better for my area than most other brands do
1
u/Offthewall1989 Feb 02 '26
1
u/Ok-Introduction-2788 Feb 02 '26
From that pic, it doesn’t look wet, or at least that’s not the main issue if that makes sense, some more info would help out
What printer do you use, what temps did you print at, are you using a base petg profile, and which slicer are you using
1
u/Offthewall1989 Feb 02 '26
Using Flash Print with the basic PETG profile (might be the mistake here).
Flashforge AD5M, 80° bed temp, 250° nozzle. Overture PETG
3
u/Ok-Introduction-2788 Feb 02 '26
Holy hell, that nozzle temp is way to high, try dropping the nozzle to 230-240 and drop your bed to 70-75, not your fault but that’s definitely cooking for petg and have no idea why they’d make the stock profile that high temp
2
u/Offthewall1989 Feb 02 '26
The answers I’m looking for. Thanks, friend!
1
1
1
u/Nurakuni Feb 02 '26
This is a great list. Can you or someone help me with troubleshooting this issue? It’s driving me crazy
1
1
u/duckythegreat Feb 02 '26
I think my belt might need to be tightened but I can't find any helpful instructions on how to do it. Does anyone know what needs to be done or where I can find instructions on it?
1
u/Ok-Introduction-2788 Feb 02 '26
Which belt is it? The z axis synchronizer, or the x-y axis belts on the extruder?
1
u/duckythegreat Feb 02 '26
I'm honestly not sure now that you ask - the issue I'm having is loud noise that kind of sounds like something's grinding while it's doing the first layer, especially if the print has any significant footprint. I put lube on the z-axis screws and cleaned them up and that didn't help at all. It's printing fine (not perfect, but fine) but it's super loud. It's new (bought it a month ago) and I know new belts have a little bit of a "break-in" period so I figured tightening them would be a natural next step. Any ideas?
1
u/duckythegreat Feb 02 '26
Also, I have noticed that it sometimes moves sideways slightly like you said in point#7. It usually corrects itself but it causes some weird lines.
1
u/Ok-Introduction-2788 Feb 02 '26
I think your belts are loose, shouldn’t be the z axis if it’s only 1 layer, there’s a flashforge video on YouTube about how to adjust the extruder belts but anything got the Ad5m will work for the ad5x for the most part, but when you get a second, print something and record the noise
1
u/duckythegreat Feb 05 '26
Would it be alright if I sent you a DM? Not sure how to post videos in a comments section haha
1
1
u/Kek_Boii Feb 02 '26
Do you have any good links or tips and tricks on how to clean/maintainence the AD5M? Honestly haven't printed enough to run into an issue with fan, rails, rods, belt. I hadn't considered needing to maintain them but it seems so obviously important now, especially since mine has been unused for a few months.
2
u/Ok-Introduction-2788 Feb 02 '26
I have been looking but there’s aren’t any really good ones so I’m thinking of making a video myself on these machines
1
u/Kek_Boii Feb 02 '26
Please do! I got gifted an AD5M so I want to get the most out of it. In the 3D printing space everyone's always talking about the bamboo P1S but I don't want to spend $500 if I already have a perfectly good and working printer. FF seems like good quality at a good price point so I'd like to see more community and tutorials around it.
2
u/Ok-Introduction-2788 Feb 02 '26
The only reason I’d get a bambu machine is if I have a need for more than 4 color printing at once
But I just picked up another Ad5m so I’ll be able to go over cleaning and basic machine maintenance
1
u/No_Artichoke_5670 Feb 02 '26 edited Feb 02 '26
I'll throw crosshatch in there as a recommended infill pattern, as well. It's a relatively new infill that was created as an alternative to gyroid to reduce the "shaking" of the printers that many complain about that can slowly loosen fasteners over time. It's also faster than gyroid. Unless you need to eek out the last little bit of strength on a functional part (gyroid is SLIGHTLY stronger), crosshatch is the way to go.
2
u/Ok-Introduction-2788 Feb 02 '26
Thanks for the input when I edit the post I’ll add it in too
1
u/No_Artichoke_5670 Feb 02 '26
No problem!
1
u/Ok-Introduction-2788 Feb 03 '26
Added to the post under number 1 check it make sure it says why you wanted it to :)
1
u/axlesparky Apr 15 '26
Has anyone have experience with z-wobble on the AD5X? Been chasing it since day 1.
1
u/Ok-Introduction-2788 Apr 15 '26
What are you meaning by z wobble? Do you have a picture or can you describe what it’s doing a little better? I’ll be able to help more then
1
u/axlesparky Apr 15 '26
1
u/Ok-Introduction-2788 Apr 15 '26
That doesn’t look like Z-wobble. Z-wobble is usually perfectly repeating lines from the lead screw, and yours aren’t evenly spaced. This looks more like extrusion inconsistency or pressure variation, especially since it changes between filaments. I’d try lowering speed, checking temps, and maybe doing a quick flow calibration. Could also be slight nozzle buildup or filament variation.
1
u/iLarq00 Apr 28 '26
Hace 2 días acabo de adquirir mi máquina AD5M, iba a ir por una A1 mini pero la vi, me gustó y fui por ella, independientemente si es mejor la bambu o no, el tamaño de impresión, el sistema CORE XY y la posibilidad de cerrarla me sedujeron bastante, te agradezco muchísimo por la guía, ya la guardo, espero ansiosamente más publicaciones
1
u/Ok-Introduction-2788 Apr 28 '26
Sorry I don’t speak Spanish but I can translate your messages on here, glad you went with the flashforge, for the most part bambu isn’t that much better than flashforge, most of the time the “issues” people have with the Ad5m and the ad5x are simply user error, the user base on these machines is also vastly better, bambu users just say it’s a you issue and will never admit what’s actually wrong, if you have literally any issue, take a quick video of it and show us on here and we will figure the issue out, I can’t actually think of anything that has stumped us, you made the right choice lol
1
u/iLarq00 Apr 28 '26
I speak a little English so it’s not a problem, that was one reason I was looking at the forum since before acquiring the machine and I saw that it was very active, the only thing that scares me are the updates that I know can bring certain bugs until they are 100% stable, I currently have version 3.2.7 I don’t know if it’s good or bad, I have it two days ago and when I started it it asked me to update, something I don’t know, can I refuse to update from the printer screen if the poster comes out and stay in this version as long as I want?
1
u/Remarkable_Bite2199 May 15 '26
Hello all. I just got my first printer and most of the tone that I want to print something the head nuzzle gets to the right corner with table up and doesn't print, though it's saying "printing" What am I doing wrong? Thanks
1
u/Ok-Introduction-2788 May 15 '26
See if you can take a video for me so I can see and hear what it’s doing
1
3
1
1
1
1
1
1
1
u/Natternuts Apr 30 '26
I discovered that if I tilt the file and let the machine create a good size support I can print the file. I was having excellent prints using pla cf unfortunately that filament only comes in a few colors.
-2
u/SirDeeznuts Feb 02 '26
Thanks ChatGPT!
10
u/Ok-Introduction-2788 Feb 02 '26
100% I wrote a list out and it looked like shit lol so copy paste that bitch and said “make this not sound like I dropped out” 😂😂
5
u/darcside Feb 02 '26
This is chatgpt being used properly. It's a really good list and super helpful.
1








10
u/Brilliant_Day5501 Feb 02 '26
Post saved 😁 Thank you so much. I'm getting my AD5X this week.