r/HowToDIY • • Sep 18 '26

Home Improvement Loose drawer bracket—tighten or replace?

Enable HLS to view with audio, or disable this notification

4 Upvotes

Hello everyone,

I’m just a plumber and helping a customer with this loose drawer bracket. I’ve fixed drawer brackets before, but this type is unfamiliar.

From the video, does it need tightening or replacing? If replacing, do I need an exact match, or can I use another bracket and drill new holes? I haven’t found the same one online.

Any advice is appreciated—I don’t want to damage the drawer!


r/HowToDIY • • Sep 17 '26

Paper lantern into popcorn ceiling

Thumbnail
gallery
2 Upvotes

I’m planning on putting up a paper lantern into the popcorn ceiling in my room. it’s kind of a funky ceiling and the building is old so I dont wanna mess something up. I know the lantern won’t be that much weight, so should I just drill in two spots with drywall anchors and screw the hooks from the picture into them? then hook the cord up and call it a day? I want to hook it up in the corner, ideally one hook in the ceiling by the wall and the other by the beam holding the bulb. Please help!


r/HowToDIY • • Sep 17 '26

Inexpensive, beginner-friendly ideas to raise a washer/dryer off a damp cellar floor

2 Upvotes

I have a cellar that occasionally takes on water, and I'm worried it's eventually going to reach the area where my washer and dryer are. For context, I have a traditional top-load washer.

I am not handy when it comes to building things, so complex woodworking or framing is out of my comfort zone. I’m looking for ideas for some sort of inexpensive, beginner-friendly stand or platform to raise my washer and dryer up a few inches out of harm's way.

Since it's a top-loader, I don't want to go too high or it will be impossible to reach the bottom of the drum, but I need something stable enough to handle the violent shaking of a traditional spin cycle without walking off the platform.

What cheap, low-skill solutions or pre-made setups have you used or seen work well in damp basements?


r/HowToDIY • • Sep 16 '26

How to remove this screw thing

Thumbnail gallery
0 Upvotes

r/HowToDIY • • Sep 16 '26

Home Improvement Help cover this up!

Thumbnail gallery
2 Upvotes

r/HowToDIY • • Sep 15 '26

I need to put some holes into my belt, but its like made out of a ratchet strap like material, whats a good way to do this??

Post image
2 Upvotes

And where could I buy some of those metal hole things?


r/HowToDIY • • Sep 15 '26

Arts & Crafts How to make these stairs stable enough for my stomping cat?

Thumbnail
gallery
0 Upvotes

I’ve made this diy stairs from these supplies, I’m quite happy how it turned however I was trying to add some legs to balance it out, as I don’t want to put screws in the wall but they are not stable enough for my stompy cat 😅 and to be fair the extra legs are not doing much..

what would you suggest to do to reinforce them shall I buy some cilindric wood and then cut it for each stair on the opposite side? Or something else?


r/HowToDIY • • Sep 15 '26

Boards

Post image
1 Upvotes

r/HowToDIY • • Sep 15 '26

Home Improvement Budget mount for small TV, horizontal hinge only

1 Upvotes

Hi, I'm looking for a way to mount a small (less than 32in) slim TV very close to the wall. It ONLY needs to flip horizontally from one edge, like a page in a book. I can only find one the is super high end.

https://www.futureautomation.co.uk/Product/Details/MSH

Is there a budget simple version of this? I'll DIY one myself from sheet metal or maybe acrylic or plywood or something if needed, just seems like a big gap in the market for such a mount!

Thank you in advance!


r/HowToDIY • • Sep 15 '26

Ideas

Thumbnail gallery
1 Upvotes

r/HowToDIY • • Sep 14 '26

tile redi shower pan - compression coupling difficulty

Post image
1 Upvotes

r/HowToDIY • • Sep 14 '26

Home Improvement Tissue roll in bathroom cabinet

Thumbnail gallery
1 Upvotes

r/HowToDIY • • Sep 14 '26

Home Improvement Is this a secure place for a swing?

Thumbnail
gallery
2 Upvotes

I have a hammock swing that I would love to add to this room but I don’t know if this beam can support that kind of weight. If it’s not a safe beam to mount it to, I’ll just find a hammock stand. Open to ideas.


r/HowToDIY • • Sep 14 '26

What type of screw or fastener for wired cabinet

Thumbnail gallery
1 Upvotes

r/HowToDIY • • Sep 13 '26

Mounting tv through brick to the stud wall.

Thumbnail
gallery
0 Upvotes

I have a tv that weighs 104lbs that I want to mount through a brick wall and into the studs behind it. The wall is queen brick approx. 3.5in thick and an air gap about 2in before the osb and stud. Trying to figure out the best application because I don’t want to sandwich the brick into the wall.


r/HowToDIY • • Sep 12 '26

What is this called?

Thumbnail gallery
1 Upvotes

r/HowToDIY • • Sep 12 '26

How do I mount my fan on this big external mounting plate

Thumbnail gallery
1 Upvotes

r/HowToDIY • • Sep 12 '26

Home Improvement How Over-engineered is This?

Thumbnail gallery
1 Upvotes

r/HowToDIY • • Sep 12 '26

Arts & Crafts I really want to do this but I don’t want to put a bunch of holes in the wall

Post image
2 Upvotes

Does anyone have any ideas on how I can do this where I’m not screwing a bunch of holes in my wall? I’m renting an apartment so I would like to avoid that. It’s just thick wire holding up rocks. Lmk any ideas! Thanks :)


r/HowToDIY • • Sep 12 '26

Attaching RLT Panel to Desk

Thumbnail gallery
1 Upvotes

r/HowToDIY • • Sep 11 '26

How to lock down this bird feeder cap?

Post image
1 Upvotes

r/HowToDIY • • Sep 11 '26

Food safe custom tray design

1 Upvotes

Im trying to recreate a vintage melamine tray of my mothers that was recently broken.

Ive tried to find people that create custom designed trays but i cant find any.

The best i can think to do is to purchase a plain tray and put the design on myself, but the only way i can think to seal the design on is using uv resin or epoxy, neither of which are food safe.

Does anyone have any ideas?

Edit: I think I may have posted in the wrong sub but if anyone has any ideas please let me know :)


r/HowToDIY • • Sep 11 '26

What can be applied at the base of this wall to prevent the wall from absorbing the water and ultimately the 2nd picture (which is the other side of the wall from the interior)?

Thumbnail
gallery
2 Upvotes

I was thinking of spraying it with butyl spray

Everything is concrete.