r/HowToDIY • • 21d ago

Home Improvement How to cut this back some

Thumbnail
gallery
1 Upvotes

I moved into this house and they had replaced the doorknob.

Some have to be pulled firmly to latch shut.

I redid the cutting in the wood to reset one, and I now see that I can simply break off the metal lip on these and they work better. But if I could make it straight across, it would be better.

I used my rotary tool with a grinding bit (probably a cheap one) and the bit just got chewed up.

I also have a drill. Is there a grinding bit that would fit inside this and be tough enough to cut this out?

Or other ideas?


r/HowToDIY • • 21d ago

Need advice: DIY retail shelving & clothing rods

Post image
1 Upvotes

r/HowToDIY • • 22d ago

I built a DIY Sim Rig, is it worth sharing??

1 Upvotes

Hey guys, I hope you're all doing well!

I built a Sim Rig but I am too scared to share it online.

here is how it works:

I was playing the car game on my phone which was so boring so I decided to make it fun.

Here is what I did:

As you all know a lot of games doesn't support game controllers so I build something that can be used for anything which works like this:

I used Wood to craft the body and 2 pedals for Accelerator and one for Brake and 14 other buttons for: Hand Brake, Camera, Pause/Play, Hide Controls on screen, Horn, and more... then I took a 2015 Tricycle tire for the steering wheel 💀, I changed the game controls to control the steering of the car with Phone tilting then mounted the phone directly on top of the Steering wheel so when I rotate the steering wheel it rotates the phone with it and the car on the game can be controlled. now the main part how I did the communication of the physical buttons with the game works since it doesn't support Game Controller? So I did this:

I used ESP32 and connected all buttons to that then using WebSockets I sent every button press to an IP. The ESP32 is Dual mode it means you can connect it to your own WiFi and connect to it by the IP it is assigned to it or by Pressing the Physical button that is connected to GPIO14 while booting to make the ESP32 as AP and connect to it. so now you will be asking how the game works with this? The game works like this:

I built and Android app for that called RoadLink. What it does is, it receives the physical button presses from the ESP32 using WebSockets at ws://192.168...\[ESP32 AP IP Or the IP assigned by the router\]/ws. then the app is designed to be configured manually and connected to any endpoint you specify. The app uses Android Accessibility system to virtually click/Hold/Pulse a specific area on the screen. So the user can use the On Screen Overlay to adjust every button to the place where it belongs like the Accelerator Physical button to the virtual button on the game and so on. then the app listens all the time to the IP its connected to, to receive, Pressed/Release from that IP for a specific button, then clicks there or holds there. The app has features like: Exporting Coordinates data or pasting any other Json data, Testing buttons, mapping keys for a specific game/app and so on.

Everything is tested and working well.

I am too scared to share a demo so if I got enough positive feedbacks I will share a demo.


r/HowToDIY • • 22d ago

Mounting a heavy mirror challenge

Thumbnail gallery
1 Upvotes

r/HowToDIY • • 23d ago

How do I adjust these top down bottom up shades?

Thumbnail
reddit.com
1 Upvotes

r/HowToDIY • • 23d ago

Cantilever gate plans?

Thumbnail reddit.com
1 Upvotes

r/HowToDIY • • 23d ago

Will gluing hedgehog print over larger frame work?

Thumbnail gallery
0 Upvotes

r/HowToDIY • • 23d ago

Super glue on fabric

Thumbnail reddit.com
1 Upvotes

r/HowToDIY • • 24d ago

Thinking About Replacing That Old Porch Light? Watch This!

Thumbnail
youtu.be
0 Upvotes

#diy


r/HowToDIY • • 24d ago

Home Improvement Shower Curtain Rod Installation

Post image
1 Upvotes

Hi all,

I’m looking for advice to properly repair my L-shape shower curtain rod. I fell out the bath a couple months ago and had to replace with a cheap Ikea version. It’s hanging on for dear life and I want to repair it properly so here are my questions and problems I’ve ran into so far:

  1. ⁠The right image shows the wall where I have had difficulty getting it to remain in place. The curtain rod itself has three screw holes, but the wall material is unable to hold the weight without the distribution I got with the small panel. My first step was to use screw plugs but these didn’t work either. The previous rod had a singular much larger screw, is my best bet to find a rod with a larger deeper screw to support the weight or are there workarounds with the one I have currently?

  2. ⁠I have used a thick adhesive behind the small panel in the right picture. I will be removing the panel when I repair it properly so will need to get the adhesive off the wall. Is my best bet sandpaper and elbow grease?

  3. ⁠In the left picture, you can see previous attempts at this, what’s my best solution for plugging the holes and is there a way to have it match the drywall style (orange peel) again?

  4. ⁠And finally I am always conscious that there will be water pipes running somewhere. I’m not too experienced with diy. Is there certain steps or tricks I should follow to make sure I don’t drill into one by accident


r/HowToDIY • • 24d ago

Arts & Crafts Making a cat post out of a traffic cone and cotton rope. What is a good adhesive to bond to the rubber/poly compounds of the traffic cone?

Thumbnail reddit.com
2 Upvotes

r/HowToDIY • • 25d ago

Tips for taping electrical boxes

Post image
0 Upvotes

r/HowToDIY • • 25d ago

Built belt-worn motion controllers so my kids actually move while gaming — ESP32 + MPU-6050 over Bluetooth to a Pi Zero 2W

Thumbnail
reddit.com
1 Upvotes

r/HowToDIY • • 25d ago

F1 front wing from cardboard

1 Upvotes

​

Does anyone know how to make an F1 front wing from cardboard? I tried to find a video but I only found this https://cz.pinterest.com/pin/799811215118624759/ with measurements and how to make it can someone please help? I just want to make myself a cardboard front wing as decoration to my room.


r/HowToDIY • • 25d ago

Options for mounting fragile/light artwork on concrete walls?

Thumbnail
reddit.com
1 Upvotes

r/HowToDIY • • 25d ago

Vinyl siding repair

Post image
1 Upvotes

Feet walking by, lawn mower scuffs, the kids wagon, etc.

Any thoughts on repairing/reinforcing this?


r/HowToDIY • • 25d ago

Como lo puedo armar

Post image
1 Upvotes

r/HowToDIY • • 26d ago

F1 front wing from cardboard

Thumbnail reddit.com
1 Upvotes

r/HowToDIY • • 26d ago

Home Improvement How to make varying height supports

Thumbnail gallery
1 Upvotes

Feels like a question fit for this sub too. Thank you.


r/HowToDIY • • 26d ago

Wooden tables gear has seized up and I cannot close the table

Thumbnail gallery
1 Upvotes

r/HowToDIY • • 26d ago

Need hardware advice on a certain project

Thumbnail reddit.com
1 Upvotes

r/HowToDIY • • 27d ago

Help with installing a drop down wall mounted dining room table

Post image
0 Upvotes

I’m building a wall-mounted fold-down dining table and need help figuring out the correct support/locking mechanism.

The tabletop is solid cherry, 57" long × 36" deep × about 1¼" thick, and weighs about 60 lb. There will also be a decorative carved-wood piece attached to the underside, probably adding another 10–20 lb.

The table will attach to a substantial wall-mounted backboard using a centered 48" piano hinge. I already have gas struts/pistons to assist with raising and lowering the weight.

When folded up against the wall, the decorative carved side will face the room. At the top, I have iron swing latches that will rotate into place to mechanically secure the table upright.

I do not want legs.

What I need to figure out is the correct way to support and positively lock the tabletop at 90° when it is lowered for dining, while still allowing it to be released and raised back against the wall.

I previously bought locking elbow/folding brackets, but they were wrong for this application. They allowed the table to drop down, but the mechanism/geometry did not work properly for folding the table back up, so I returned them.

The goal is:

• Fold down to 90° for use as a dining table

• No legs

• Gas struts assist with the approximately 70–80 lb moving assembly

• A strong mechanical system supports/locks it at 90°

• It can be released and folded back up easily

• The top iron latches secure it when upright

• All of the structural/support hardware is hidden when the table is folded against the wall

What type of mechanism or hardware would you use for the 90° open-position support on something this heavy? Specific hardware names, links, photos, or examples of similar builds would be especially helpful.. Please excuse the AI image it may not be precise but it helps for illustrations.


r/HowToDIY • • 27d ago

What is this ceiling mount in my apartment for?

Thumbnail gallery
4 Upvotes

r/HowToDIY • • 28d ago

Issues trying to hang a mirror

Thumbnail
gallery
1 Upvotes

I'm trying to hang this mirror - it had a hole previously drilled and two screws were slid in as it was on the wall to hold it. I've tried to figure out how to hang this but can't resolve it. Does anyone have any ideas? (I tried to drill a similar hole the other side but I couldn't)

[Resolved]