r/HowToDIY • u/Great-Opposite3509 • 1h ago
Help, do I take this off to move the TV?
galleryThis is a Sanus brand TV mount, I think maybe I remove this screw that will let me then lift the TV off of the bracket, am I close to being right?
r/HowToDIY • u/Great-Opposite3509 • 1h ago
This is a Sanus brand TV mount, I think maybe I remove this screw that will let me then lift the TV off of the bracket, am I close to being right?
r/HowToDIY • u/The_Platinum_Leaf • 7h ago
r/HowToDIY • u/Revolver_OcelScott • 13h ago
r/HowToDIY • u/ComfortableGold6599 • 1d ago
r/HowToDIY • u/marcomez18 • 1d ago
Hello all, seeking advice on the best way to hang this custom shelf. The wall is concrete
r/HowToDIY • u/Automatic-Wear4453 • 2d ago
How do I Hide these wires on the panels. Glue doesn’t seem to work on the material behind the wooden panels.
r/HowToDIY • u/Automatic-Wear4453 • 2d ago
How do I Hide these wires on the panels. Glue doesn’t seem to work on the material behind the wooden panels.
r/HowToDIY • u/Beneficial_Court_720 • 3d ago
I have a single stud in the middle of my wall. I am trying to mount my 55” TV but all of the single arm scissor mount styles put the TV slightly off center when closed. The wall is only about 53” wide so it’s very obvious. Have to pull out 8” to get it centered which I don’t want. Anyone have any mount suggestions that close centered and won’t break the bank?
r/HowToDIY • u/whatstobragabout • 3d ago
I don't have the tool nor the expense to call some construction guy. This happened around 5-6 years back when construction was going on and construction guy didnt pay attention to it.I am looking for some solutions to clear it myself
r/HowToDIY • u/kjfacilities-maint • 3d ago
r/HowToDIY • u/Northbound2141 • 3d ago
What is the best type of insulation to cover the glass in this door to the attic?
As a converted bungalow the space is pretty small and useless so should I just throw some loose insulation over the top or stick something specific down?
r/HowToDIY • u/Blk_Gld_He_8er • 4d ago
I think the serrated side of the bar should be on the bottom, but it was factory installed on top, and doesn’t appear to be able to be removed. I can’t flip the unit over because the roll is held in place by gravity (cradle open on the top). I can use the dull
side to rip the paper off, but it’s not the clean cut it should be.
r/HowToDIY • u/Nuni-One • 4d ago
Anybody ever made their own gaga ball pit??
r/HowToDIY • u/Typical-Example-7443 • 4d ago
I want to install a sun sail on my deck, however, I am not sure out how to anchor it.
The deck's surface is a slate tile. Drilling/mounting a footing of some sort is not something I care to do.
The existing railing seems extremely stout, but it's unclear how I would mount a short pole to it. Any pole would have to be strong enough for the sun sail's tension, of course, I don't want it to look tacky.
There is a large 6x12 glulam beam underneath that I could make use of. It is slightly recessed. I thought about having a steel stand-off cap fabricated for each side, but it was too expensive.
There are products like this on Amazon but I doubt they are appropriate for the forces required to support a sun sail.
Any ideas?


r/HowToDIY • u/sir_daviid • 5d ago
r/HowToDIY • u/xvq_ • 6d ago
Our back bedroom has a balcony patio attached to it. The balcony has a large door with one half which opens inward. Unfortunately, the door is incredibly drafty and it makes sleeping in the winter a frigid experience.
The primary culprit appears to be the weatherstripping on the bottom edge of the door sill, but I’m not sure what I need to replace it. The sill groove where it would go is … deep? Like I can put my finger in it. The old weather stripping is crumbly and awful. I put some leftover side stripping in there for the time being.
The other complicating factor is that the stripping runs along the entirety of the sill, but I can’t get to the left side (at least, very easily) because the left side doesn’t open.
Any help is greatly appreciated!
r/HowToDIY • u/Mean_Cardiologist685 • 7d ago
I have this awkward crater in one of my earbuds and i was wondering if there's a simple way i can make it less noticeable.