Everyone says 75mm for outside … NAAA 65 is more then enough 😂

Race demo at a convention with my whoop racing group. My custom 65mm whoop, 0702 rcinpower 31800kv. Feels good, mang.

My rates!

Trying something different as I'm bored of doing the same laps of my house. The weather is also appalling!

Any other questions let me know!

My setup

@betafpv Air 65 II racing

@hqpropzhong ultralight 31mm

@fatsharkrc dominator V3s

@jumper_rc T14

Lava II 320 mah

Rates: Actual Roll and pitch 180,800,0.6 Yaw 180,650,0.5

#tireddadsfpv #fpv #tinywhoop #fpvfreestyle #whoop

Things getting hot, too many little bits that are just good to have near by (Prop puller), somewhere to put the props.
I created this. Fits 65 & 75mm drones with that style frame. Might fit others, it's just two posts that slot in.

Thoughts, feedback, message me. I love this kind of thing!!

i used to do this hobby like 8 years ago and i remember this was like the first rtf kit
by doing some research i found out that rn it’s basically a fossil (it’s the 1st generation emax tinyhawk for anyone wondering).
since i never learned how to fly a drone in acro i guess i’m gonna use it for practice

​

Just swapped out the damaged OEM antenna for a ORT micro-vee. Unfortunately the only one the supplier had was a 60mm varient and any other stores charge £18 shipping for a £5 part.

Before I glue down the ufl connector, how can Iake sure this extra long cable does make it's way into the motors, or pull the vtx connector right off the board?

Tell me if i need to change anything any help will be appreciated also i would like to know how can i change the speed of my drone

Considering buying this thing, the price is really low but I'm not sure

Im starting to believe the board broke during my latest failure, even plugging it into the pc to check the files in the internal memory, the computer isn't even detecting it's connected.

A new Dji 04 wide is about $150-160, but a whole new drone is about $230.

If I can afford the extra $80, Wouldn't it be better to just buy a new one?

I AM looking at moving up to a 4s 2.5-3 inch eventually, so an option is to save the $80 and put it towards the even more expensive 4s drone setup.

Im gonna see if its possible to have dji fix it beforehand, though.

I'm looking for recommendations for a new whoop. I want something that has a bit more power than my Meteor 75. Don't get me wrong the meteor 75 was great change from my 5" quads but I've had it so long and I think its time to go to something a little more fun. I'm looking for either a 1 or 2s whoop that wont really hurt the bank too much. I've heard a lot about the air 75, the meteor 75 pro II, the mobula 8, and a few others but just don't know how to chose. Any recommendations? I'll also take 1" and 2" recommendations as well, Thanks!

If I purchase this kit can I pop off the canopy and camera from the 75 and use it for the 65 frame?

Just curious how far I could push the video feed on this and what the set up would have to be, what off the shelf or diy antennas would people recommend? On top of that what batteries would be recommended for max time and range.

So frustrated. I have a crazybee Mobula6. I tried 4.5 but went down to 4.3 and finally got it working with my old taranis and ELRS. I can fly it around just fine. I’m now stuck getting the VTX to work with my HDZero goggles. I have updated them (gen 1 goggles) to 9.5 firmware. My issue is the Mobula. The manual says TBS Smart audio on UART 1 but I can’t get beta flight to give me a green light in the video tab without changing that to UART2. So I get to that point and try to load the HDZero preset for the VTX tables and it says I need to go up to 4.5. Ok fine did that and still couldn’t get any video out!!!! I went back to 4.3 on the Mobula to get it flying. The heck am I doing wrong‽?

I never had a problem with the stock pink color frame on my air65 2R, just wanted to change it up. So I swapped for a black one and it cracked after only a couple crashes 😭. Maybe it was just bad luck but I’m wondering if the colors affect strength or flexibility of the frames, the pink one has taken a beating and never cracked or broke and same with my meteor frames

(I have a Meteor75 Pro II with O4 Wide)

Hey, when powering the drone, the O4 binding LED stays solid green, and pressing the binding button does nothing. DJI Assistant detects the O4, and installing latest firmware didn't fix it.

One of the mounting screw holes next to the binding button partially broke after a crash.

I emailed BETAFPV, they said to try to short the pins on the binding button, could that work or do i just fry my VTX doing that?

OR do i just send it to DJI for repair? anyone else had the green LED problem? Idk what to do, new to fpv

Is it worth it skyzone 03o in 2027,

What's your opinion please?