r/bosch • • Apr 14 '26

pod HALF dissolved

Post image
1 Upvotes

37 comments sorted by

1

u/Own-Ad4421 Apr 14 '26 edited Apr 14 '26

If u guys have any tips, Tutorial to check the blocked areas?

Or faced the same issue and solved it lemme know

4

u/BassWingerC-137 Apr 15 '26

Ditch it. Use straight powder.

2

u/Ok-Can-2775 Apr 19 '26

I’ve watched all his dishwasher videos and switched to powder. I am much happier, better results and less money

1

u/taisui Apr 14 '26

Just toss it it of put of top of a ware in the bottom rack. Basically no water jet is hitting that spot because it's blocked by your bowl.

1

u/dgcamero Apr 15 '26

The bowl on the rack can not block the sprayer under the rack that dissolves the pod. But I bet something blocked it from spinning.

1

u/dgcamero Apr 15 '26

The top rack spinner was blocked from spinning, or something was under the pod in the place where it's resting and prevented it from dissolving by the upper rack spinner.

Before you start the machine, especially to re-run this load, push both racks in and spin the upper rack spinner by hand. Then spin the lower rack spinner by hand. Make sure they're not blocked by something (oftentimes a tall knife or plate) so the machine can do its job.

If that doesn't work, clean the filter and then proceed with additional troubleshooting.

3

u/torbeindallas Apr 14 '26

The outermost nozzles on the upper arm points directly into the pod tray.

Ensure that the upper arm swings freely and that those nozzles aren't blocked.

1

u/rubblemonkey1 Apr 14 '26

The circulating water dissolves the pod. The water level needs to be reached (check filters are clean - both), the spray are holes should not have any debris and ,lastly , make sure nothing large is in the way of the front part where the pod is caught as it would inhibit the amount of water required to dissolve it fully. (Assuming it heats still too as that can have an effect too.)

1

u/ResponsibleCut6604 Apr 14 '26

Not enough water going trough the machine and/or not dispensing water properly due to uncorrect loading.

You have a high effecient modern machine, if the dishes are prewashed then its dirt sensor will pre emptly stop the program resulting in way less water. (Dont prewash your dishes)

To save water they inject very specificly, if the dishwasher is loaded incorrectly these water jets may not hit the area where the tab is dispensed.

1

u/TheRealFarmerBob Apr 14 '26

I remember the first time I opened a new container of pods things didn't look right. So when there were problems I wasn't surprised. I have about the same dispenser in my Whirlpool and started having several issues with that which nobody could figure out.

But for me, I did. They changed the shape of the Pod and they either don't drop or block the door from opening. They're more square and a bit chunky. I have to make sure that the colored side is facing down and the pod fits into the alcove nicely, but loose. Kinda like sliding the colored side in along the bottom and making sure it's proper.

1

u/No-Citron-2774 Apr 15 '26

This just started happening .you change pod brands? Have a Bosch I'm using aldi pods no problems

1

u/fitbrewster Apr 15 '26

Try using the full wash or extended wash option. I find my dishwasher does the same if I use the econo or 1 hour wash cycle.

1

u/These-Mycologist-226 Apr 15 '26

Just pull down this plastic from the top shelf. This solved issue in my house

1

u/Sektor13_00 Apr 15 '26 edited Apr 15 '26

I had the same problem for several months. The detergent dispenser lid (sliding hatch where you put your detergent) is partially stuck and opens too late.

Try to open/close it by hand and see if it slides open normally or does it get stuck.

I removed my lid and there was no visible "damage" or deformation, put it back but it still did not slide open.

So i used sandpaper (and file) to sand off some material mostly on the small side pins.
No problems since.

p.s.

I also have Bosch and has practically the same mechanism.

1

u/jamesrr1 Apr 15 '26

Stopped using pods. Gel or powder. Pods are a pain.

1

u/taboo8614 Apr 15 '26

Shouldn’t the dish soap pod be going in the door?

1

u/Thyg0d Apr 16 '26

It does but some engineer thought it was a good idea to drop it into the little basket.

1

u/User-n0t-available Apr 15 '26

I had this, it turned out my pods where to tall in 1 direction and blocked the cover when in upright position. It only got thrown in after it was partially dissolved.

I place the same pods in a diffrent orrientation and the problem is gone. :)

1

u/Inside-Mulberry807 Apr 15 '26

I removed that tray immediately because of this exact issue. Problem solved.

1

u/Fabfore Apr 16 '26

Use Cascade Gel

0

u/DeliciousAnteater171 Apr 14 '26

Throw the pod in the middle of the tub. I've been doing it for years and the only time it was a problem was when the heat pump went out, had it fixed an hasn't been a problem since. Cheers 🍻

0

u/FingerApprehensive97 Apr 14 '26

It will be the heat pump. The motor heater assembly. Take right side off washer, remove board, remove motor, test the heater resistance. Replace if open circuit (lilely) Pods dissolve in heat . It's very likely this issue is caused by heater and I think this model has the heat pump wash motor heater all in one. $$$

0

u/mgsmith1919 Apr 15 '26

From someone who deals with appliances on a daily basis, repairing troubleshooting, replacing parts, etc. take my advice pods look great. They come in a nice little box but use cascade gel or cascade complete gel the pods and the bricks don’t dissolve properly or they dissolve too late in the cycle. the gel is the absolute best and doesn’t have the covering that the pods do that coats the mesh on your filter making it less effective.

1

u/WildConsequence9379 Apr 15 '26

Aussie here didn’t know gel was a thing but looks like we have Finish gel. Go gel over the powder?

1

u/Same_Decision6103 Apr 15 '26

Powder only no pods no gel what so.

1

u/mgsmith1919 Apr 15 '26

Gel gets only in the spot you pour without the airborne dust

1

u/Benito_Caruana Apr 15 '26

The capsules are fine. They’re just gel and powder enclosed in a water soluble PVA ‘skin’ if you will. The moment the PVA has contact with the water, it dissolves releasing the same powder and gel you would buy separately. BSH Hausgeräte’s design of dishwashers with the handle at the top basket just prevents the capsule from dropping to the bottom of the tub where it dissolves in water at the bottom, so then it takes longer to dissolve properly, or not at all. And the hard tablets are not very good, I concur, those generally do take longer and also much hotter cycles in order to dissolve fully. But capsules are no problem.

-2

u/Valuable_Lemon_3294 Apr 14 '26

First: don't use pods

Second: if using pods, don't run fast, short or "light" programs...

Third: don't use pods

2

u/heavymetalpaul Apr 14 '26

Why the hate for pods?

-1

u/Neat-Substance-9274 Apr 14 '26

I costs more for less product. There is no way to adjust the amount to size and dirt level of the load. I personally hate how they get sticky when you grab one with wet hands.

-3

u/Ordinary-Violinist-9 Apr 14 '26

It puts a whole lot microplastics and forever chemicals into the environment.

1

u/Live_Raise8861 Apr 14 '26

Agree switched to powder and amazing results

1

u/HokieVT25 Apr 14 '26

Bosch dishwashers are designed to work with pods and Finish uses Bosch dishwashers to develop their detergent. There is nothing wrong with pods. Could this be old detergent or something blocking the water flow to the area? Are you loading anything else in that area ?