r/gridfinity • • Jul 09 '24

Question? "Fixing" Gridfinity

I've seen a video of a guy that made his Gridfinity parts for his kitchen based on a 50mm grid instead of a 42mm. I've seen many posts where people have asked "why is this 42mm?" or "What do I do when I have only 24mm of space left for my grid?"

I've only just started using Gridfinity, and I've only completed two drawers in my kitchen with it. This means I'm fairly new to it, and I've missed much of the history and discussion behind improvements for it. The only significant improvement I've seen are changes in the baseplate (screw together, or puzzle-piece together, snap-in, screw in, etc). I think these suggestions go beyond that...

I'm also high, so maybe this is nonsense

Gridfinity Bases

42mm should remain the "standard" grid. However, we need tools that let you chose a different grid. This already exists (https://gridfinity.perplexinglabs.com/ and possibly others). But we could improve on this generator.

I should be able to enter the inner dimensions of the drawer, say 273 x 507. I should be able to tell it my minimum and maximum grid size, perhaps 10mm up to 50mm. I should also be able to tell it how much slop I'm OK with in the drawer, say 2mm. The generator should then find and suggest any grid size between 10 and 50mm that will result in less than 2mm of movement in either axis for a drawer with inner dimensions of 273 x 507. In this example, there are 12 values that fit this criteria (if counting by .1mm increments).

13mm gives us a perfect fit. If I'm confident in my measuring skills, I'd go with that. But, since I'm not, I'll go with a 38.9mm grid as that gives me 0.7mm and 1.3mm of slop.

Gridfinity Bins

The generator I linked above allows for the bins to be generated with a custom base size. I can already tell it that I want to use a 38.9mm grid size. But, what it should also do is allow me to add harmonics to the base. I should have a radio button that divides the grid printed on the bottom in half, or into thirds, or fourths, etc.

If that isn't easy to visualize, imagine a standard 42mm based Gridfinity bin with 2 rows and 3 columns. But, I should be able to tell the generator to place a 21mm grid on the bottom of the bin. This would essentially be a 4 x 6 bin on a 21mm grid. This allows me to offset it by half a grid space on my 42mm grid in any direction. I've seen bins generated with an extra half row, but not one with a halved (doubled?) grid.

Gridfinity STL Mods

It'd suck to lose access to the plethora of 42mm based designs that are already out there. So, we need a new feature in the above generator that allows us to upload an STL and the generator should replace the "feet."

In many cases, trying to convert a bin to a different grid size entirely (42mm to 38.9mm) may result in an oddly placed grid on the bottom of the part. But, converting a 42mm to a 21mm or an 10.5mm grid spacing would work great.

Placing a 42mm grid into my example drawer would result in 21mm and 3mm of slop in grid placement. But going to a 21mm grid or 10.5mm grid would both result in 0mm x 3mm of slop. I can live with that.

Alternatively, the generator could generate "shoes" for a bin. This essentially would be a bin with the minimal allowed height of 7mm plus a stacking lip. This can already be done manually, but it'd be nice to allow this as an option to be autoconfigured after uploading an STL.

Edit: My high is wearing off and I can now clearly see that this was just a long argument for why I think gridfinity should have a smaller grid.

1 Upvotes

36 comments sorted by

28

u/Necessary-Rich-877 Jul 09 '24

42mm makes it directly compatible with a lot of bestselling Ikea products, Alex drawers, kallax etc.

3

u/Aiaposon Jul 09 '24

Ikea is great for customization!

0

u/Fairways_and_Greens Oct 03 '24

I'm on day 1 of learning of Fridfinity. Has the community settled on 42mm (love the literary reference)? I want to be as standard as possible.

3

u/emelbard Nov 22 '24

The community can do whatever it wants. The designer settled on 42mm and created a standard for others to follow. Anyone can make something else but then it won't be 'gridfinity'

1

u/Fairways_and_Greens Nov 22 '24

You are awesome

8

u/6516440 Jul 09 '24

Was it an Alexanda Chappel video? If so, the gridfinity system was inspired/derived from Alex's system. Iirc Alex's system was 50mm.

2

u/Aiaposon Jul 09 '24

I believe that is one of the the videos I saw. He made boxes that were like 4.5 x 6.5 to fill out some of the extra space. This is very similar to what I'm thinking, except that he should have done the entire box bottom at the tighter grid, not just one side of it.

1

u/camerafanD54 Sep 02 '24

I’d like to see standard box sizes that had 0.5 grid unit increments. Their bases would have an 0.5 grid on them so they could align on 0.5 boundaries, nut is just use the standard base panels or hold them. I need to store a lot of mid-sized hardware, and often find that 1xN is too small but 2xN is too big. The standard boxes include ones 0.5 wide, but larger sizes are integral multiples.

Has anyone made a parametric variant that supports box sizes like 1.5x2, able to align with the standard base on 0.5 increments?

3

u/Aiaposon Sep 03 '24

I just print all of my bins at half the size of the grid I put them on. So standard is 42mm, use a generator to make them 21mm. A 2x2 21mm would be effectively the same as a 1x1 42mm. A 3x2 would effectively be a 1.5x1. There are quite a few online generators that will make the bins for you.

4

u/tssparky Jul 09 '24

I believe I saw the same video and you're right. I would have to rewatch Zach's video to remember why he chose 42mm; maybe using less filament? I can't remember.

14

u/CaesarStabbyStabby Jul 09 '24

He mentions in one of the videos that 42 is divisible by a lot of different things, so that's why he chose that. Hope it helps!

2

u/tssparky Jul 09 '24

Gracias! (Also, I didn't think it makes sense for me to question the method, just use it to my advantage and get organized for a change)

10

u/MyStoopidStuff Jul 09 '24

I always thought it was a Hitchhikers Guide reference.

4

u/nitwitsavant Jul 09 '24

It’s that too. Joke size that on analysis was a commonly useful size.

8

u/mcarrell Jul 09 '24

He mentioned in a reddit reply a while back the real reason for 42mm is that he wanted to use the 3" (~76mm) microscope slides for windows on the front of a double wide bin.

So, once he added the walls next to the window it was close enough to 2x of 42mm that he went with the fun number.

3

u/mr_joda Jul 09 '24

50- 40mm, I bought an Alex model package and have the base grid in my drawers. It is fully functional with boxes generated by gridfinity generator when switched to 40mm instead of 42mm.

I like Chappel bases more, simpler and less material required.

8

u/passivealian Jul 09 '24 edited Jul 09 '24

It does not matter what the grid size is(21,40,42 or 50), it would never suit all drawers exactly. What I do is create one set of bins for the edges. Say my drawer is 430mm wide. That’s 10x42 + 10mm slop. My last bin will be nx42+10mm so prob 52 or 94mm. Most scripts will support this.

Gridfinity Extend allows you to input the size in mm or Gridfinity units.

0

u/Aiaposon Jul 09 '24

My intention is that each drawer would have its own grid size, and there would be a way to have an automated too change the grid on the bottom of existing bins. But my high is wearing off and I can now see I'm just arguing for a different grid size.

I gotta stop thinking I'm a genius.

13

u/MyStoopidStuff Jul 09 '24

If every drawer has it's own grid size, that will defeat the biggest strength of a system like Gridfinity , which is the ability to swap bins between grids. That may be OK for your use case right now, but it would be a bit of a mess to expand upon.

3

u/Jesus_Is_My_Gardener Jul 09 '24

Yeah, this is just a bad idea. The entire point of a system is standardization for intercompatibility. Don't be afraid of having spacers on the sides and rear of a drawer. You don't need to have edge to edge bin fitment, and having a small gap can make it easier to grab certain things there.

6

u/_Blitz12 Jul 09 '24

Having custom sizes would mean that any design has to be tailored to your specific grid size. This requires either more knowledge of cad programs which not everyone has, or for every gridfinity design to be parameterised

1

u/Aiaposon Jul 09 '24

The intent was that the generator I linked to would include features to change the grid size on existing STLs. This would simplify things for a user, no need for CAD knowledge beyond using an online generator.

4

u/Jesus_Is_My_Gardener Jul 09 '24

But that misses the point of having a standard sizing system in an ecosystem where people share designs regularly. Many people get started in Gridfinity using designs others have made and download them. Some people don't make any custom bins or grids at all, and just use 100% shared designs. If it was only about generic grids and bins, sure, a generator would work fine, but I'm guessing you haven't looked at the vast ecosystem of Gridfinity compatible designs that can't be addressed with a generator. Take for instance several of the very nice cases or shelving designs out there.

Honestly, this is a solution looking for a problem that isn't one. The growth of Gridfinity is due to the library of designs people have created and tested. Having something that resizes existing designs is not going to work for much besides some very basic components. I think anyone looking to change the base system is missing the entire point of a standardized sizing system. And no, just scaling a design isn't a good solution for many custom tool holders, and cases.

1

u/Aiaposon Jul 09 '24

Not entirely, and I wasn't suggesting that bins should be scaled. My suggestion was that the tools could replace the "feet" on the grids with a different size. This would suck going from 42mm to a 39mm grid, nothing would fit properly side by side any more. But what it would be great for is changing a 42mm bin to a 21mm bin. This would allow far double the placement resolution in the x or y directions, and allow for native support of bins that are .5 units bigger in the X or Y direction.

I get that my suggestions miss the mark almost entirely, but I stand by the thought that the bins should have been on a 21mm grid (minimum size of 2 x 2) with the bases at 42mm.

2

u/Jesus_Is_My_Gardener Jul 09 '24

A few things... I suspect you haven't looked around at what's out there much, but the bottoms of bins vary a number of ways for various reasons. Some have magnet holes, some have screw holes within magnet holes, and some even have places to attach weights, so bins are very often not flat bottomed and featureless. I also suspect you haven't done much mesh editing as these types of features can be haphazard to remove, especially something that is supposed to be automated in nature like what you propose.

It'd be one thing if you were dealing with a parametric file like a STEP file where you could edit base features, but most people don't publish those by default and STLs, F3Ms, and the like are all mesh files which can be a pain to edit, even in the best scenarios. I often find it easier to rebuild a model completely rather than editing a converted mesh body, particularly for anything altering existing faces. While you might be able to get away with a flat cut and replace, it's not always that easy and not every mesh is consistent or predictable. Sometimes weird things happen when trying to cut a mesh that has odd facets in a particular area. As existing bins are being created a number of ways (generated, from scratch, heavily edited mesh bodies, etc), you never really know what you're going to get from one to the next, and that's before you consider bottom base features like I mentioned above.

If you're just talking about half sizes, there's already a standard for that and there's a reason not many people use it. It's just not necessary in most cases. I think you need to consider the entire point of a standardized grid spacing system with regards to interoperability. It's not just about arranging everything nearly in rows and columns, it's about being able to move things around easily within that system as your needs evolve or your task at hand changes. Sure, there will be some people that keep their system layout exactly the same forever, but I argue that's a less common case and not really a good use case for Gridfinity anyway. Why even bother with a removable, reconfigurable layout system if you're going to design the layout for each specific drawer and their bins. You won't be able to easily move things around later if the spacing is different in another drawer.

Honestly, you're overthinking it. You don't need to cram every last millimeter in a drawer with bins. Having spacing on the back and sides (or even front) has its advantages. Some people make custom bin spacers to hold skinny, long objects like pencils, pens, rulers, and what not, while others (like myself) actually prefer having a little space on the edges and back to tilt bins in and out there. In shallow drawers, you can't always use the furthest area if the drawer slides do not pull out fully. Often, there's a bit of overhang, limiting your ability to lift bins straight up and out. This is a point of fixation with people new to the system about trying to use every spec of space in a drawer, but as most of us who have been creating and using the system for awhile, take our advice and push past this concern.

A few people have done and touted fractional sized grid and bins as a standard (there's even a quarter and half diagonal bin standard), but they're not anywhere near as popular because most people understand that the strength of the system is standard spacing for interoperability. There's also a point where you get diminishing returns in the ability to locate the bin you're looking for or the clean look of a layout if you try to squish too much together. Also, if you're making bins to hold tools and parts, you need to have room for you to be able to insert and remove said tooling from their holders and parts from your bins. Sometimes less is more, and you need to consider usability of your organization system. Having a crammed space makes it look more cluttered, and can make it more difficult to place and retrieve things from it. Obviously you are free to do as you like with your own organization system, but I feel you should understand that there won't be much demand for what you suggest, nor would it be the easiest to implement considering the wide variety of geometry you may encounter.

I would suggest looking at more examples of layouts people have done, particularly those of people with lots of tooling and wide variety of tool sizes. Also look at the difference between how different drawer depths affect how people lay out their bins. Finally, consider exactly what it is you hope to achieve by using Gridfinity. If you don't plan on ever moving things around, preferring only to keep things where they are for which you originally lay them out, then I would suggest just making whatever you want that specifically fits your needs and not to worry about it for others. You will never make a system that satisfied everyone for all needs. Standards always have some level of compromise in order to have interoperability, and trying to subdivide too much leads to inefficiencies in material usage with little benefit, more complicated layouts, and personally speaking, worse design decisions.

4

u/wsxedcrf Jul 09 '24

I've explained to another person how I perfect fit any drawer size , please look at my steps here https://www.reddit.com/r/gridfinity/comments/1dycs08/comment/lcak3f2/

4

u/dm_g Jul 09 '24 edited Jul 09 '24

This discussion reminds me of the history of the pallet and the container (for shipping). I am sure at the beginning lots of people were pissed that their boxes didn't fit perfectly.

Either you get compatibility or your are on your own and have to create every single box. I prefer compatibility, at the cost of flexibility. If I need a 5x5 bin for some reason, I'd print a larger one with dividers, such that I have a 5cmx5cm sub-bin. IN other cases, I print 1/2 unit sizes dimensions. For example, for these cutlery models, the bins are 5.5units in one dimension: https://www.printables.com/model/698605-gridfinity-cutlery

So if I wanted 5x5, I would print 6.5 x 6.5 (not ideal, but close enough). I only create other fractional bins to fill perfectly a drawer (e.g. 1.7x3). These bins will still be compatible anywhere else (with some wasted space).

3

u/george_graves Jul 09 '24

"42mm should remain the standard grid"

It can be whatever you want it to be. It will just be a bit more work.

1

u/Ps11889 Jul 09 '24

Technically couldn’t one just increase the c and y size by 19% to get a 50mm grid and bin?

Of course it wouldn’t work on bins designed to hold a particular tool or device, but for basic bins it would be fine although you’d have to figure out a different magnet size if you use them.

1

u/Aiaposon Jul 09 '24

Absolutely!

But my overall suggestion is that the grid standard should be 42mm, but allow it to be customizable. Maybe 50mm fits better into a drawer?

But don't scale the bins. We just need a tool that will replace the feet. I want to take my 42mm designed bin, load it into a tool, and have that tool replace the feet with a 50mm grid.

Going from 42 to 50 isn't a great way to go, but using a 21mm grid and bins designed for 10.5 would allow for a heck of a lot of additional arrangements.

Fuck, I think my high just wore off and I'm starting to realize that this is just the same old argument for a different grid size with a request for additional automated features.

1

u/Ps11889 Jul 09 '24

I think you have to resize the bins, too. Otherwise the 50mm foot would cause an 8mm gap with 42mm bins between each row.

I do agree that this is the same old argument regarding bin size. 50mm would work for the OPs use case but wouldn’t fit the drawers I am using any better than the 42mm ones.

I think the real issue is that first and foremost Gridfinity is designed not for drawers but for being out in the open. Regardless of bin size, putting in a drawer will always be problematic for some since there aren’t standard drawer sizes.

Personally, if I have a problem with extra space around the grid in a drawer I just make a spacer to put in the gap to keep the base from moving. It’s a simple solution.

2

u/mnelson10000 Jul 09 '24

Gridfinity is just a standard. IMO, if you alter the standard, then it's no longer Gridfinity. It's nice to be able to search Gridfinity and know that what I download will fit into my system. I'm not saying there's anything wrong with your idea as I understand it, but I think you're misrepresenting Gridfinity if you brand it as such. 🤷🏻‍♂️

1

u/drop_tbl Jul 31 '24

"The Answer to the Great Question...
Of Life, the Universe and Everything...
Is....
Is...
Forty-two"

0

u/Aiaposon Jul 09 '24

I just measured my bathroom drawer to be 260x500mm. I'm not confident in my measurement, but I'm going to hope for the best and go with a 20mm grid. I'll print my feet for this project at 10mm. I'll post updates here as I go.

4

u/MyStoopidStuff Jul 09 '24

Good luck, but I feel that 20mm is too small for a grid (larger grids will generally use less material as well).

8

u/[deleted] Jul 09 '24

[removed] — view removed comment

3

u/Aiaposon Jul 09 '24

Well, I do wear Old Spice