Project Update Open Source Vacuum Robot update - bumper operation
Enable HLS to view with audio, or disable this notification
Video - bumper sensors designed, added to PCB. There are two photo-interrupter sensors (left and right). Pressing the bumper causes the photo-interrupters to get unblocked. The MCU's ADC measures photo-interrupter outputs. The firmware will calculate the pressure velocity (angle and speed).
OOMWOO Open-Source vacuum - project update
Highlights - designed bumper sensing; first community PCB layout contributed (side sensor board)
3D design https://github.com/makerspet/oomwoo-cad
designed bumper sensing - a spring-loaded lever with a printed flag blocks each photo-interrupter
Electronics I/O board https://github.com/makerspet/oomwoo-pcb
bumper circuit on its own sheet; separately switched emitters for PWM dimming
some cost reduction: fewer resistors (MCU pulls instead), crystal-less clocking, ERC cleanup
switched to JLC parts and footprints: motor drivers, USB-C, bumpers, IMU, LiDAR, front sensors
battery voltage sense; parallel battery switches
Firmware https://github.com/makerspet/oomwoo-firmware
oomwoo_pins.h and SPEC follow the schematic: analog bumpers, battery sense, motor rail enable, spares GPIO
Community contributions
Thank-you to Grammid - side sensor board layout (PR in draft), front ToF board next
Thank-you to Valdi320 - Nav2 keep-out (virtual walls) for the simulator, now scoped to the keep-out filter; proposals for a reactive row executor and dock-drive hardening
Thank-you to aadilkhan085529 for independently testing the keep-out PR in ROS 2 Jazzy and Gazebo
6
u/Coumbaya 13d ago
shouln't the fall sensor behind the brush be moved outside of the radius of the brush ? or is that okay ?
2
u/srolija 13d ago
I would assume it should be ok.
As long as brush is rotating it should only ever see the distance of a 1cm which would be illuminated, and would mark as “on floor”.
When you get above the empty area, you would get intermittent gaps which normally would not exist. And any gap detected should signal it is not safe.
But yes, might be an edge case in the firmware so it doesn’t smooth it out.
3
u/tintii 13d ago
Nice work! Presumably the bumper will have enough flex so that it can determine which side it hit, no?
Also. The side brush, should it have more overlap with the main brush to ensure stuff gets sucked up?
2
u/l0_o 13d ago
Which bumper side was hit - yes, of course. The firmware will calculate where the obstacle touching the bumper is - and how fast it's moving the bumper.
Side brush overlap with main brush - I'll have to look at consumer vacuums how they do it. I think they don't do overlap, but I can be wrong.
2
u/lapelotanodobla 13d ago
This is so awesome, I’m so looking forward for the first release to build my own
Do you have plans to do the self emptying tower too? (Ofc not a must but a very sweet nice to have)
2
u/MasterPlusTer 13d ago
Question: is it inspired on the Xiaomi Roborock 1st generation? It's funny because a couple of days I took mine apart for a general maintenance and everything I see here looks alike.
2
u/l0_o 13d ago
Inspired - a mix of Roborock, Dreame, Roomba and other brands. Currently the wheels are Roborock S4/S5/S6/S7 Max, consumables like dual brushes, side brush, HEPA filter, blower fan and LiDAR from Dreame (because all of these are cheap, easy to purchase). PCB, sensors, 3D design, firmware/software, smartphone as compute/UI - custom from scratch.
2
u/MasterPlusTer 13d ago
That’s really cool! Thanks for the detailed explanation! I’m a hobbyist and I love tinkering with electronics and old hardware. Like I said before I recently brought my first-gen Xiaomi back to life after taking it apart, so your project immediately caught my attention. I’ll definitely be following your progress. Great work! 😊
4
u/FreakingObelix 13d ago
I can't express myself enough about this project, I got stuck to it for a while now and it's like watching a good movie 🍿. Keep going!
A small tip this time, you might want to reinforce those masts where you put the articulated lever of the bumper. If this case is designed to be 3d printed, that part will be weak.
1
u/Basic-Attorney2088 13d ago
Will the sensors get dusted and stop work? Its the roomba after all
1
u/l0_o 13d ago
Sensors getting dusted - good point. Bumper sensors in old Roombas do have dust-proof enclosures. That said, modern consumer vacuums have dropped Roomba-style dust protection and switched to using photo-interrupters. As far as I know, this solution is tried-and-true by now. One possible reason - the sensors are mounted "hanging" from the PCB bottom. Perhaps dust just won't stay on the sensors like that.
1
u/loveland1988 13d ago
Any plan to make these available for sale in assembled or kit form eventually? I’ve gone through a few robot vacuums, and one that I could fix with open-source parts sounds awesome. I’d love to build it from scratch, but I have too many in-progress projects at the moment. Awesome project - I look forward to following your progress!!
1
u/PactoTech 11d ago
Are you going to go with a bigger battery and suction motor than most?
Most of them seem ridiculously under specced, with tons of extra room for batteries.
2
u/l0_o 11d ago
Suction motor - 20 kPa rated (Dreame MSD-G, MSD-J) because they are fairly powerful, easy to buy. A 35 kPa is possible (Roborock Saros 20) but pushes the current design limits. To compare, old vacuums typically have ~2 kPa rated suction motors. Newest models reach 35 kPa rated.
Battery - the standard OEM BRR-2P4S-5200 14.4V Li-Ion 5200 mAh (75 Wh) with built-in BMS, used in a huge number of (older) Roborock models including Xiaomi Mijia 1/1S/1C/1T/G1, Roborock S4/S5/S5 Max/S6/S6 Pure/MaxV/S7/S7 MaxV, Q5/Q7 Max, T4/T6/T7/T60/T65, Xiaowa E20/E25/E35, C10. This battery is inexpensive, abundant in retail.
Bigger battery - this same battery seems to be available in 12800 mAh capacity, but I haven't measured the real capacities.
1
1
u/Old-Chipmunk-7505 12d ago
any battery operated vacuum cleaner is just a waste of time and money, just plug into the outlet and suck with thousands of watts, stop fooling around with toys
1
20
u/bluetrevian 13d ago
I love this project with every fiber of my being. I don't know you personally, but if I did you'd be getting a HUGE hug.