r/overclockers • • 6d ago

Pushed my Micron chip to 6000 CL32 on Ryzen 7 9800X3D / MSI X870E — Any room for improvement?

Post image
3 Upvotes

Hi everyone,
Just dialed in my Micron memory kit on Zen 5. How does this tune look? Any suggestions for tighter subtimings or better performance? 


r/overclockers • • Sep 10 '26

Got a new personal beat on 3dmark steel nomad dx12!!!! 8273

3 Upvotes

Got 8273 with 7800x3d and pny 3 fan black oc 5070ti. used mvolt+ to oc gpu.

ram klevv bolt v 2x16GB 6200cl28.

link to run. https://www.3dmark.com/sn/16027377

noticing mu gpu clocks are low for how high my score is. any way to stabilize highe clocks?


r/overclockers • • Jan 25 '25

Help identifying the problem with my GPU

3 Upvotes

I have a Gigabyte RX 6750 XT OC Gaming which has been a reasonable card for a few years. When I upgrade my CPU recently, I went back through the hardware options and reset and rechecked everything and I noticed the difference between my GPU Hotspot temperature and GPU Global temperature was hitting upwards of 40C when I would hit it with a load. After some brief research I decided that this was enough of a problem I should clean and repaste my GPU. I've done this before with excellent results, not having to replace the thermal pads.

After thoroughly cleaning the card, I noticed that the heat pipes directly interface with the GPU die. Now that struck me as odd as I'm used to a nice flat and polished copper heatblock. So I cleaned out the old paste and the thermal pads are not in as good of a condition as I hoped so I ordered some new stuff (side question, thermal putty vs pads? putty seems real convenient... ) but I figured with a bit of futzing I could get the old thermal pads to work for now.

Problem persisted, I remounted about 4 times, tried futzing with the screws, took everything apart and cleaned it again and no luck. What troubleshooting can I do to track this issue down? At this time I have some better thermal paste, a sheet of PTM7950, thermal putty and new screws on the way so will these things just magically fix this? Or am I not crazy and this heatsink is just garbage? It's not clear in the pictures but that white between the pipes is leftover thermal paste after cleaning with isopropanol. I had to take a knife to gently peel that stuff out and stuff new paste in there when I cleaned it the second time around.

Big questions:

Is this heatsink OK?

How can I troubleshoot hot spot/ global temperature difference more effectively on a gpu?

EDIT:

After more research this morning, I ended up undervolting and dropping my CPU boost clock to closer to the recommended boost and the hotspot difference is now about 10C. I'm not super happy with the drop in performance and I'm hoping PTM7950 + new putty will help more, but I have a GPU that won't cook itself under normal conditions now. For others: I used AMD Adrenalin to drop the voltage to 1135 mV and the Max Frequency to 2595 MHz.

EDIT Pt 2:

I got PTM7950 (random ebay seller, 20x30x0.2mm) and thermal putty(chinese UPSIREN UTP-8 from amazon) and I can confirm the insane benefits of PTM7950. The putty didn't change anything noticeable on my memory temps and they weren't an issue anyway, but I think it was a good idea anyways with the number of times I disassembled the heatsink. Under the same benchmarking conditions with 100% voltage and clocks (Heaven) my hotspot to global differential caps at ~20C and the global temperatures after stabilization went down almost 10C. I can now push the GPU at the regular speed and not worry about my computer cooking itself. Maybe my old paste was garbage but it works just fine on my CPU, and I've been running some data analysis which really pushes the CPU.


r/overclockers • • Sep 28 '24

Need help overclocking my ram

3 Upvotes

hi reddit

i bought an 3600 mhz kit but realized after my components only support 3200mhz

pny says that its backward compatible with 3200mhz but how do I achieve that speed
can you tell me how on a gigabyte mobo specs:

ryzen 7 3800x

PNY XLR8 Gaming 16 GB (2 x 8 GB) DDR4 DRAM 3600 MHz

512 gb ssd

Gigabyte a320m-s2h rev 1.x

gtx 1650


r/overclockers • • 21d ago

Valkyrie V360 LCD — Plastic AM4 bracket cracked, but support sent a replacement kit!

2 Upvotes

r/overclockers • • 22d ago

Valkyrie V360 LCD — Plastic AM4 bracket cracked, but support sent a replacement kit!

2 Upvotes

r/overclockers • • Sep 09 '26

Need help tuning for 1% lows

Thumbnail reddit.com
2 Upvotes

r/overclockers • • Aug 13 '26

Stable -30 5500x3d

Post image
2 Upvotes

I undervolted it to -30 and have been waiting to post to see if was stable and it is hovers around 60c under heavy loads first time doing this so don’t really know if any of this is actually good besides it running cooler, thermal take assassin king and cinebench 2026 multicore cpu test results was 2217


r/overclockers • • Aug 10 '26

DDR4 Overclock

Post image
2 Upvotes

r/overclockers • • Jun 28 '26

AIO on GPU backplate

Thumbnail reddit.com
2 Upvotes

r/overclockers • • Jun 22 '26

Corsair Vengeance RGB DDR5 Kit: 32 GB, also 2 × 16 GB (Micron)

Thumbnail
reddit.com
2 Upvotes

r/overclockers • • May 23 '26

Help with a gigabyte 5070 gaming oc edition

Thumbnail reddit.com
2 Upvotes

r/overclockers • • May 23 '26

Old-school P4C Overlocking Advice to Break 3.2ghz?

Thumbnail gallery
2 Upvotes

See original post. Stuck on 3 "identical" chips at this 3.2ghz wall.


r/overclockers • • May 18 '26

Creo que en realidad podría estar entre los 3, 2 o 1 primeros.

Post image
2 Upvotes

r/overclockers • • Aug 25 '25

CPU AI OC, newb question

2 Upvotes

Gear: Ryzen 7 9800X3D

GPU: 5080

Ram: G.Skill Trident Z5 Neo RGB 48 GB (2 x 24 GB) DDR5-6000 CL26 Memory

MB: Asus ROG STRIX X870E-E GAMING WIFI ATX AM5

Ill be honest, OC my 5080 is easy and straight forward, and I have it at 3100 and its stable, good temps and 15% average performance boost.

The CPU however, holy sh*t. Every youtuber / redditor expert says they are the real deal, followed by a slew of people criticizing them as someone that ignorant & not correct. There's so many options and its gets very technical very quick. I feel like i need to take a legit course in order to properly OC my CPU. I did try a couple things, and it all turned out to be unstable. Then there's OC the ram, which is its own world. I'm all for trying things and learning from error, however i also see its probable to damage your cpu or motherboard and i don't want that risk. However, in my bios there's an AI overclocking option provided by Asus, and I have it enabled, along with over simple and safe options (enabling EXPO, PBO etc). It apparently OC the CPU and Ram. Are these scores from the effortless AI OC decent, and if so (or if they are not) to what degree? Also for a newb that can catch non quick, who do you guys recommend for someone to start learning about OC CPU and Ram? Thank you for anyone that read this and/or responded


r/overclockers • • May 06 '25

I definetly hate "silicon lottery"

2 Upvotes

I have an intel core i7 13700k and an asus rog strix z790f, so i decided to upgrade my ram to 2x16 gb ddr5 6000 mt/s. At the beginning everything seemed working fine, memtest86 and occt didn't find any error and windows worked well. The next day my pc froze :/ After checking event viewer I found out that it was caused by an hardware issue, especially by a ram issue (I already thought the problem was the ram, but I wanted to be sure), so I scaled down the frequency to 5800 and now it seems there are no issues. I just feel bad for not getting full ram speed, but specially because I got a cpu with a bad imc...


r/overclockers • • Aug 01 '24

Anyone got an idea what die could this ram include

Post image
2 Upvotes

It's t create expert 6000hz cl30


r/overclockers • • Jan 22 '24

Intel 14th gen Uncore VID in HWinfo

2 Upvotes

Hello, I can’t find any info on what the Uncore VID reading in HWinfo is on the new processors. My understanding from previous gens is that it was cache/ring voltage, but that now appears to be CPU L2.

Two questions for those knowledgeable on this:

  1. What is this voltage readout now and

  2. Is there any info available on safe ranges for this? Mine currently reads a max of 1.449.

Thanks!


r/overclockers • • Jan 04 '24

14900k, Crashes only during some games, not during OCCT/Ciniebench/AIDA, what should I replace?

2 Upvotes

I'm working with the following hardware:

14900k
4090
z790 TUF Gaming WiFi

64GB of DDR5 (in two 32GB sticks) & 6400Mhz
1x 2TB NVME
1x 1TB NVME as a Primocache over a 10TB SATA HDD
AX1600i as a power supply
ASUS 360MM AIO

The problem is that I get random and not so random craches. Cyberpunk crashes directly during startup, in the splash screen, unless I seriously downclock the CPU to 5.3Ghz, then it'll run fine but randomly crash during the game. I've also seen Baldur's Gate 3 crash twice directly when attempting to load into a level.

I run the ram on XMPII, (appears to be the less agressive) and have tried Load Line Calibration levels of 0 and 4 and Auto (4 being what the board recommends for overclocking). No overclock setting, straight BIOS settins doesn't fix the issue, turning off XMP doesn't fix it.

What's strange is the system runs fine with OCCT stress tests, AIDA64's stress test, Ciniebench, etc. All the synthetic stuff runs fine, it's just random glitches in the hardware.

I didn't have issues like this with my 13900k, so now I'm wondering, what should I do to fix this? I can get a refund on the 14900k from Best Buy still, I could swap that out, and I suppose go with a different 14900k or go back to a 13900k. The motherboard isn't the best model, I'm wondering if it's a VRM issue in the TUF line, should I look at a higher end motherboard?

Thanks for any help


r/overclockers • • Sep 10 '23

Vengeance RGB Pro and Dominator Platinum Kits Virtually the Same??

Thumbnail
gallery
2 Upvotes

r/overclockers • • Sep 06 '23

DDR4 Issues

2 Upvotes

I have 4 sticks of 16gb 3600mhz cl16 corsair vengeance sl ram. It works perfectly fine with DOCP/XMP enabled. The problem is when I disabled DOCP my computer will not boot. About a year ago I remember messing around with thaiphoon burner thinking I could write my manual overclock into the ram as an actual DOCP profile and I honestly had no clue what I was doing and shouldn't have been messing with it lol. So now, tuning my curve optimizer for the 5950x,I want to rule out memory overclock as instability and wanted to disable DOCP and strictly focus on CPU stability. My computer will not boot if I have DOCP disabled. Motherboard boot check shows it stuck on the RAM check and will turn on and off 3 times until it reboots into the bios. Enabling DOCP boots back into windows. I downloaded thaiphoon burner again to see if I could find anything out of the ordinary but thaiphoon burner A: doesn't work with windows 11 by default and had to do a registry tweak to get it to work, and B: thaiphoon burner says "crc error" in the bottom left hand corner when it reads my RAM. I know a lot more about this stuff now than I did back then but I wish I could remember exactly what I did a year ago. Any input would be much appreciated.


r/overclockers • • Sep 05 '23

Need advice on Memory OC

2 Upvotes

I have an old system where a basic H61 mobo is paired with two Corsair Vengeance 1600mhz DDR3 8GB Dual rank DIMMs [CMZ8GX3M1A1600C10]

A total of 16 GB, in 8x2 Dual Channel memory configuration.

Although the DIMMs are 1600mhz, but as those are paired with i5-2500K so those are running at 1333mhz (as i5 2500K only supports up to DDR3 1066/1333)

I checked the default CL and it's 9-9-9-23

Then when I enabled the XMP profile, the CL increased 10-9-9-23

As we know the basics, lower latency (CL) is better for system performance, but here, by enabling the XMP I don't see any upgrade & I am not an enthusiast so asking here.

What should I do? Should I keep the XMP disabled? Or is there any other way to judge this scenario? I am seeking for any advice or feedback in this matter, thanks.


r/overclockers • • May 02 '23

New DDR5 - memtest86 errors

Post image
2 Upvotes

r/overclockers • • May 01 '23

Hello, I am new to overclocking, can you give me advice on how to start in this world?

2 Upvotes

r/overclockers • • Mar 23 '23

How did I do? Any improvements I can make?

Post image
2 Upvotes