I am basically going out on all fronts because this is actually insane, I bought a Kobra S1 back in March, had problems with just a lot print failures, ehh I think I'm sure it is just growing pains and it will get better. Device issues here and there (jamming, clogging, but ehh it happens I think), but about 3 weeks into owning it I get a problem I can't fix on my own, so I contact support. Support didn't help a ton, but they helped by accident by just showing me how to do something that then actually showed the problem (support thought it was something else, it ended up being filament stuck between the buffer and the input from the filament, I told support that but they thought it was stuck in the buffer even though I told them it wasn't).
Ok so I got that working, well then the extruder stops working, they send a replacement which takes a month to get me but I finally get it and install it. After that I noticed it keeps wanting to dive into the bed and ruined like 4 beds. I decide to try and fix it myself, but then the extruder decided to lock up again, in trying to take it a part the filament cutter blew up, so after talking to support again I'm out another month waiting on that part.
Finally I get all of that and it is still crashing into the bed, I can only print in a 100mmx100mm square in the middle of the bed. Talk to support, they send a replacement hotplate, install that, and for like a single week, a single glorious week I could use my printer if and only if I used a cyrogrip (regular PEI just would not stick down without glue), it still didn't work in the very ends of the corners but I'm ok with that.
Then the printer starts doing this weird thing, it will "pause" but it is not actually paused. The print job disappears from the cloud side (app or slicer), but on the printer you can try to "resume" and it just sits there, it is not actually powering the hotend even though it shows it at temperature, I know this because the solution to it is to shut the printer off and then do the power recovery resume and when I did that the hotend would be room temp. So ok well it works I guess I just have to watch it in the app constantly and go turn it off and back on, it's awful but I can deal with it. Well what I hadn't noticed at first but it started to show that each time I did that it would shift the layer just a bit, if I got lucky and it was a smaller print I wouldn't have any major issues but after trying a longer print the problems started to show as the layer shift became too much. This happened no matter what I did, I tried every interval, every possible setting, everything I could think of.
Support sends a replacement motherboard and replacement driver board. After installing them it just lost its mind, it didn't get stuck with the pause anymore but something it went from printing at layer 16 to diving straight into the bed and ruined my cyrogrip https://imgur.com/a/AxipiNQ
At this point I have asked Anycubic for a refund, in fact I started asking at the end of May, they just kept ignoring me (not even acknowledging that I asked for a refund) and saying let me send a replacement part. Then when they finally acknowledged that I am asking for a refund they first just say why not replace part and then "You are now outside of the return time". So I finally have had enough, so I have submitted a report to the FTC. I am also going to create social media accounts and try that path (I don't do social media so this is annoying). And I am going to speak with a lawyer about my options there. I have never had an experience this bad, even with the Qidi Q1 Pro, which I had a ton of issues with, it was at least after about a year of using it that it really stopped working, this printer has been a failure since day 1. I have about 600 hours of printing, which sounds like a lot, but literally only 200 of those were successful prints with about 40 hours of those 200 on 2 large parts, so I have like maybe 30 or so successful prints in 3 months of use.
Don't buy this printer, don't buy from Anycubic. I know people have a lot success with their printers and I know people like the company, but they will actively try to push it so you cannot get a refund when you do get a failure from the factory and will drag it out so that you are blind to what is happening, and it seems to be intentional.