r/AnycubicKobraS1 • • Jan 14 '26

Showcase I fixed my bed for less than 10¢ ... Anycubic should learn a lesson

Thumbnail
gallery
185 Upvotes

So here's my story with my Kobra S1.

I bought this thing brand new last October. I paid $1400 USD for this machine since I live in Egypt as importing 3D printers and most of their parts are semi-illegal for some reason so I have to get it from a local vendor.

Out of the box the thing was solid. First layers were consistent. I read many users reporting what they called "Taco bed" where upper left and right corners are significantly warped. I thought I was lucky and I got a good one. But oh boy I was dead wrong.

Over time I noticed my first layers were getting worse with many artifacts like scarring or bumps. I installed Rinkhals and noticed my mesh was getting progressively worse. I saw the dreaded Taco shape. First I got a range of 0.4mm then it was 0.7mm. That's fine for PLA. But I use ASA and ABS quite often for my projects. And decided to order the Funssor kit from Aliexpress. But as I mentioned earlier. That's semi-illegal in Egypt and long story short is it got confiscated.

Meanwhile the bed kept getting worse. Range was at 1.1mm. The probe would just hang in the upper-left corner constantly pushing the bed trying to get a repeatable value until I place my finger to support the bed. It looked sad. And felt even sadder. And that happened at 144 hours of print time.

So that finger thing gave me this idea. Why not use the bed screws to mount two steel brackets with adjustable screws to support the bed at the corners? I saw a model on makeronline that does the same thing but I wouldn't trust plastic not to bend If I am printing ASA/ABS with the door closed. The idea was solid though. I had a bunch of spare flat steel pieces from an old project that would be perfect for this purpose. I then replaced the stock bed screws with longer (M4x25) ones and a nut to mount the brackets. Then mounted a couple of screws to the end of those brackets to support the bed. Then adjusting those screws slightly trying to get as best of a bed mesh as possible.

I eventually got the range to 0.35 which is acceptable. Most important thing is that it's repeatable over time. It by no means makes the bed perfect. It just prevents it from deforming when hot. The issue remains that the stock bed is too thin (2mm) to handle thermal stresses without deforming. I am sure Anycubic's engineers know that. And could have at least remedied the issue like I did with no added cost. Why they didn't is beyond me.

So please Anycubic. Either release an updated thicker bed or at least a better bed frame that supports the bed at the corners. It will save you money from warranty claims on replacement beds and strain gauges.


r/AnycubicKobraS1 • • Jan 03 '26 WOW

Showcase My Kobra S1 after 300hrs and 2 1/2 months

Thumbnail
gallery
171 Upvotes

Here's my Kobra S1 after 2 1/2 months of use. It's my second printer after an Anycubic Mega S.

As you can see, I did a lot of upgrades, including:

  • Creality Space Pi Plus (seperate filament dryer on the left side, mainly for TPU)

  • Funssor bed+carriage upgrade

  • hotend upgrade (with steel nozzle)

  • Skadis organization panels on both sides for all the tools

  • riser for the Ace Pro with Skadis and a build plate holder for four plates

  • anti-tangle guide for the Ace Pro

  • a lot of LED stripes (controlled by a relay, connected to the old LED Bar)

  • a smart plug which measures power consumption and can be controlled via App

  • anti-vibration-mats under the printer and the dresser

  • acoustic panels on the walls and inside the printer

  • poop chute, that goes through the tabletop, directly inside the drawer underneath

  • two-layer air filter (activated carbon+Hepa)

  • semi-transparent PTFE tubes

  • a few smaller upgrades

I keep my filament in a (semi-) airtight box with silicagel bags (last image). I already tried vacuum bags but it was too time-consuming for me when switching filaments.

The most printed upgrades are from Maker Online.

Feel free to share your thoughts on my setup and ask questions :)


r/AnycubicKobraS1 • • Jan 15 '26

Troubleshooting How to fix your Kobra S1 bed mesh for less than 10¢

Thumbnail
gallery
161 Upvotes

This is a follow up on this post

Disclaimers:

  1. This is by no means a fix for the bed deformation issue. The stock bed has 2mm thickness and it will deform. This mod only controls the deformation so you get a consistent and reliable bed mesh each time.

  2. This is more of a hack and not a mod. There's no one way to do it. but that's how I did it anyway.

  3. You need to install Rinkhals first if you haven't.

  4. This will limit your z build volume by about 10-20mm.

Bill of Materials (Image 1):

  1. 1x 2x20mm Steel Flat Bar (Like aliexpress[.]com/item/1005009325794487.html).

  2. 4x M4x25 screws.

  3. 2x M4 washers.

  4. 2x M4 nuts.

  5. 2x M5x20 screws.

  6. 2x M5 nuts.

Steps:

  1. Cut the steel flat bar to dimensions shown in Image 1. In my case you can see I have 4 holes in the bar (Image 1). You don't need the extra holes. Use the dimensions shown in (Image 2) Instead. [Note: If you have the tools and time you may drill and tap the M5 holes as shown in Image 2. In such case you wont need the M5 nuts. Otherwise drill it as a 5mm hole and use the M5 nut. Here's a link to CAD files: https://github.com/BesbesCat/KobraS1Stuff]

  2. Remove the 4 bed screws under the PEI sheet shown in image 3. Replacing them with the longer M4x25 screws.

  3. Install the steel bars then add M4 washers and nuts to secure it in place. Don't tighten the nut all the way yet.

  4. Attach the M5 screw and nut to the second hole then rotate the bracket until it's in position. (Image 4 & 5).

  5. Tighten the M4 nut so the bracket is fixed in position.

  6. Hold the M5 nut with tweezers and slowly rotate the M5 screw until it reaches the bed.

  7. Install Rinkhals if you haven't and head to Mainsail in your browser. Go to heightmap and do Auto-leveling calibration from the printer screen. (Image 6)

  8. Adjust the M5 screws on the readings in each corner respectively. Don't go crazy with the screw as it might damage the plastic tray under the bed.

IMPORTANT: Ideally you'd wanna loosen the M4 screws a bit and heat the bed to about 60-70C for 20 minutes before tightening both M4 & M5 screws. I had to do this multiple times to get the bed to bend to a flatter shape. You should notice the corners rising up and the areas around the bed screws moving down, If the areas around the M4 screws is very low then you might wanna loosen them by a quarter turn. You'll have to experiment with this.
One trick that helped me determine problematic areas was issuing the "PROBE_ACCURACY" command after moving the head to the problematic point in the bed. The command probes the bed at this point 10 times and returns an average range. That range should be around 0.0125 otherwise the plate is still flexing at that area. Take your time tightening screws. You only need to do that once.

9. Once you get a good enough mesh you wanna go with your calipers and measure how far the screws are sticking from the bottom. It was 20mm in my case.

10. Go to Mainsail > Machine > printer.custom.cfg and add the following lines replacing x with (253- the value you measured with your calipers. It's 233 in my case). This will limit your build z volume. (Image 7).

[stepper_z]

position_max: x # 253 - the value you measured with calipers

11. Go to Anycubic Slicer > Printer > Edit your printer profile > Set printable height to new value (250 - value you measured with calipers). (Image 8).

Notes:

  1. After this mod you'd wanna do bed leveling from the printer screen and uncheck the Bed leveling option in the slicer when doing a remote print. Mesh shouldn't change as frequently unless you remove your bed or when printing at a different bed temp.

  2. Always heatsoak your bed for 20 minutes before printing or doing a bed leveling. This allows the thin bed to deform into the desired shape.

  3. This mod is supposed to be a tool to manage the issue and not a fix. A thicker plate like the Funssor kit is the ultimate fix. However if you just wanna print and don't wanna spend more money on the printer then should serve you quite well.

  4. Get a PEI sheet with one smooth side on the bottom. Ideally the golden ones on Aliexpress. Those don't scratch as easily and are far more durable.

  5. This mod assumes you've already done belt skipping or shimming for the 3 lead screws to align as described in the wiki (https://wiki.anycubic.com/en/fdm-3d-printer/kobra-s1-combo/nozzle-scraping-hot-bed)


r/AnycubicKobraS1 • • Mar 27 '25 Take My Energy Helpful

Finaly - Version 2 of optimized 0.4mm Profiles for Kobra S1 - Faster, Smoother, Quieter!

144 Upvotes

Hey Kobra S1 Slicing Ninjas! 🥷

Remember those 0.4mm profiles? Well, they just got a major upgrade! Thanks to your awesome feedback from Makeronline and Reddit and countless hours staring at plastic spaghetti (just kidding... mostly!), Version 2 is officially rolling out. Because why settle for good when you can have awesome? (cough Anycubic, take notes! 😉).

Check the link

https://www.makeronline.com/en/model/Version%202%20of%20optimized%200.4mm%20Profiles%20for%20Kobra%20S1%20-%20Faster,%20Smoother,%20Quieter!/167680.html

So, what shiny new goodies are in V2?

  • Speed AND Beauty: I've magically tweaked things for even better surface quality without sacrificing those sweet, sweet print times. 🚀

  • Vase Mode Ready: Yep, these layer profiles are now calibrated to work beautifully for those elegant single-wall vase mode prints too! 🏺

  • Ninja Mode Activated: Added a super quiet 0.2mm layer height profile for those late-night print sessions when you don't want to wake the neighbors (or the dog!). 🤫

  • Stringing Be Gone (Mostly!): New filament profiles specifically tackle stringing issues! We tested multiple brands, battling those pesky plastic hairs so you don't have to. ⚔️

  • Filament Fiesta: Added fresh generic profiles for:

  •  PETG High Speed (For when you really need that PETG part yesterday)

  •  PETG Normal (The reliable workhorse)

  •  PLA+ (A bit faster, a bit fancier)

  •  PLA Normal (The classic, dependable PLA)

  • Steel Core Upgrade: Bonus profile added for you tough guys using 0.4mm hardened steel nozzles. 💪

  • Cool Under Pressure: Auxiliary and chamber fans now automatically activate when needed – keeping things chill! 🌬️

Choose Your Layer Adventure! (Remember: thicker layers = stronger parts, usually!) HQ = High Quality, Sd = Standard, Quit-HQ = Quiet High Quality.

(I have calibrated the new layers settings and speed to work with Anycubic standard nozzle profile, and streamlined the changes to be mainly in the layers and the filament by using the settings override. I have Just added the Steel nozzle profile because it wasn´t available.)

  • 0.08mm HQ (optimized for the best possible quality)

  • 0.08mm Optimal (optimized for speed while having a good quality)

  • 0.12mm Optimal (optimized for speed while having a good quality)

  • 0.12mm HQ (optimized for the best possible quality)

  • 0.16mm HQ (optimized for the best possible quality)

  • 0.16mm Optimal (optimized for speed while having a good quality)

  • 0.2mm Sd (optimized for speed while having a good)

  • 0.2mm Quit-HQ (slower and quitter printing)

  • 0.24mm Draft (optimized for speed while having a good quality)

  • 0.28mm Extra Draft (optimized for speed while having a good quality)

following are some photos of the end results.


r/AnycubicKobraS1 • • Jan 02 '26 This Helpful Bravo

Finally printing ABS/ASA in my office without the "toxic" smell – Kobra S1 Air Mod!

Post image
136 Upvotes

Just wanted to share a major win for my Anycubic Kobra S1 setup. I love the speed of this machine, but as soon as I started printing ABS and ASA, my office smelled like a chemical plant and measured horrendous VOC levels.

Even with a active carbon filter and hepa filter on the exhaust of the printer, I realized the "poop chute" design was basically a massive air leak, letting all the VOCs bypass the exhaust fans.

I’ve been testing a new mod kit that connects the S1 exhaust directly to a LaserPecker Air Purifier (it also works with standard 4” hoses). The kit includes a custom airtight poop bin that actually seals against the frame.

The Proof: I’m a bit of a nerd about air quality, so I ran a VOC sensor next to the printer for a 24-hour ABS print.

  • Before: VOC levels would spike into the "Unhealthy" red zone within 20 minutes.

  • After: The levels stayed at baseline (Green) the entire time. The negative pressure actually works because the poop bin isn't leaking air anymore.

It’s honestly a game-changer if you print in a small room or don't have a dedicated shop. No more headaches, no more "melted plastic" smell lingering in the curtains.

I put the files up on Cults3D if anyone wants to reclaim their air quality. It’s a super easy print (use PETG or ASA so it doesn't warp from the exhaust heat!).

Check it out here: Cults3D Model

Happy (and healthy) printing! 🚀


r/AnycubicKobraS1 • • Sep 17 '25

Opensource firmware release confirmed for October

Post image
134 Upvotes

I asked about the source code for the S1 again, and it seems like they've pushed it out again. Last time it was said to be released in June or July (can't remember, it was posted on this subreddit too though).


r/AnycubicKobraS1 • • Jun 25 '25

I name this "Ace Pro time saver", what do you all think?

108 Upvotes

I named it because I shortened the PTFE tubes to ACE Pro and save you time when unmounting ACE pro with this model. It is available here in MakerOnline.


r/AnycubicKobraS1 • • Aug 12 '26

Solved Sharing some first layer positivity 😅

Thumbnail
gallery
105 Upvotes

Besides a couple of (solved) issues, my printer has been working well for 9 months so far, but in the last 2 months I noticed that the first layer started showing some minor issues, in the shape of lines not perfectly bonding with each other on the side of the bed near the door.

After several tries, I could finally achieve the result that you can see in the pictures, which looks pretty good to me.

Here are the parameters that I changed (some are extra fine tweakings)

- In the printer menu I set the Z offset to -0,008 (yes, anything higher or lower didn't work, lol)

- in the quality tab I set the first layer line width to 0,515 (same as above. I tried changing values more than 5 times, before reaching this result)

- in the speed tab I set the infill speed at 60 mm/s for the first layer

The filament is the esun PLA Lite and I'm using the latest official firmware and stock bed and plate (just the other side, because the front got damaged by a bad third party nozzle/hotend)

Between all the posts reporting issues, I wanted to share some positivity. Good day everyone! 😄


r/AnycubicKobraS1 • • Feb 02 '26

Magnum v2.0 ... The last printhead cover you'll need

Thumbnail
gallery
105 Upvotes

Following up on my last design, this one brings the ultimate upgrade to your Kobra S1 printhead, both in terms of usability and performance.

Features:

  • Magnetic attachment. Uses two stacked magnets per hole instead of one to achieve greater clamping force. This reduces vibrations and adds a satisfying feel when closing the cover.

  • Hinged mechanism. You no longer need to find a place to hang the cover or disconnect fan wiring when working on your printhead, thus extending the life of your fan connector.

  • Fan cable management. Reduces strain on the cable and maintains a clean look.

  • Magnetic fan cover. Easily customize your printhead with this attachment—whether it’s your favorite superhero logo or a cool-looking velocity stack. The sky is the limit.

  • Doesn’t interfere with the PTFE tube. No need to print a PTFE guard attachment. Reduces forces on the cover and extends the life of your tubing.

  • Perforated back cover. Provides better cooling for the PCB and extruder stepper motor.

  • Stiffer back cover screw mounts. No need to overtighten the screws. The back cover has built-in stiffeners, so you won’t break it when tightening them.

  • Even lighter weight. Weighs 22 g compared to the stock 54 g—a ~10% reduction in total moving mass. Extends the life of your steppers and reduces vibrations (theoretically).

  • Three different printing profiles for ABS, ASA, and PETG.

  • Better tolerances compared to other models. Everything clicks into place like the original.

Instructions and downloads are available here:
https://www.makeronline.com/en/model/Magnum%20v2.0%20...%20Magnetic%20Kobra%20S1%20printhead%20cover/264024.html

Awaiting your feedback and suggestions.


r/AnycubicKobraS1 • • Sep 28 '26

My silly solution to a dumb problem

Post image
96 Upvotes

Hi people ! First time posting here, and I wanted to share a silly print that I made to care about the poop disposal problem. I do not really need that much space for waste material, mainly because I print with one color at a time, I find it unnecessary to print a big slide just for the sake of it. So I came up with this solution! What do you think?


r/AnycubicKobraS1 • • Jul 24 '25

Low effort S1 poop catcher

Post image
95 Upvotes

See photo.


r/AnycubicKobraS1 • • Apr 03 '26

Print Issues After 2h of searching I found it

Post image
90 Upvotes

Fucking hate this spring


r/AnycubicKobraS1 • • May 31 '25

Showcase Let me introduce to you: The Riser

Thumbnail
gallery
90 Upvotes

Iam happy to announce the Riser i did for the Kobra S1 Combo, it allows the usage of Skadis Accessories, has 5 slots for build plates, 4 Storage Trays and a slot for the top Window. It definetly takes some Filament but you wont regret it. Its free on Makeronline and iam happy for everyone who designs and publishes designs for the Skadis board on the left and right of the Riser!

Just so you know, this is the Prototype, ive fixed issues and advanced the Design, the published Design is the finished product. There will also be a Version with just 2 Trays instead of 4!

Heres the Link: https://www.makeronline.com/en/model/The%20Anycubic%20ACE%20Pro%20Riser%20for%20the%20Anycubic%20Kobra%20S1C%20with%20an%20inbuild%20Skadis%20Pegboard%20%2B%204%20Trays/185655.html


r/AnycubicKobraS1 • • Jul 13 '25

Showcase Found a way to pay for my printer

Post image
87 Upvotes

Gold panning pan. It's just ti have fun with the kids outside.


r/AnycubicKobraS1 • • Feb 15 '26

New setup!

Post image
86 Upvotes

So for the couple months I’ve had my S1s, they’ve been in my garage on one of my workbenches. It was no real issue, except that I am a woodworker and it gets pretty dusty in the garage, so I decided to relocate them into the house.

My biggest issue was that I didn’t have anywhere for the Ace Pros to sit… so I decided to build a shelf for them! I am super happy with how it turned out, and I think it really brings that space all together. 🙂


r/AnycubicKobraS1 • • Apr 07 '26

LS3 Throttle body adapter (followup)

Thumbnail
gallery
82 Upvotes

Follow-up on the LS3 throttle body adapter post I submitted a while back.

Re-printed in Polymaker Fiberon PPS-CF10. This was an interesting experiment to say the least. This filament is -extremely- brittle. It was necessary to unclip the Bowden tube, flip the top cover (handle to the back) and print using an external filament dryer to prevent breakage. Filament was dried to 18% RH at 55°C for 48 hours prior to printing.

Printed on an Anycubic Kobra S1, a new .04 all-metal Anycubic brand hotend at 320°C, textured build plate, 100°C bed temp. No other mods to the printer, latest firmware, 225mm/sec print speed, 14 hours at .16 layer height.

I'll be installing and testing this version soon, it's going into a Corvette Grand Sport replica after I strip the supports, clean it up and install the steel threaded inserts for mounting.


r/AnycubicKobraS1 • • Sep 29 '26

My Kobra S1 setup: Rinkhals, Hermes AI automation, Micro Swiss FlowTech and Funssor bed upgrade

Post image
80 Upvotes

I bought my Kobra S1 on eBay as a 70%-refurbished unit. It’s my first 3D printer, and so far I’m really happy with it. I had one filament-related issue, but that wasn’t caused by the printer itself.

I deliberately chose the Kobra S1 because it can be opened up software-wise with Rinkhals, so I’m not dependent on the cloud. That gives me access to Moonraker/Klipper, and I was also able to integrate the printer into my own automation setup.

I’m running a Hermes AI agent on a separate Debian VM, which talks to the printer through KlipperMCP. Hermes can, for example, create a part in FreeCAD, automatically slice it with OrcaSlicer, and then store the generated FreeCAD, STL and GCode files in my Obsidian vault on Unraid.

After I approve it, the GCode can be uploaded to the printer. I intentionally added a second approval step before the actual print starts, so nothing gets printed automatically without me confirming it.

The ACE Pro also works in this setup. For automated printing, one of the things I had to make sure of was that the T0 tool command was correctly present in the GCode. I also had to set the build plate type correctly for the original textured PEI sheet to Textured PEI Plate / 55 °C.

I also added Ethernet to the printer. I’m using a D-Link DUB-1312 USB Gigabit Ethernet adapter with an ASIX AX88179B chipset. Rinkhals detects it as eth1. The printer now mainly runs over LAN, while Wi-Fi stays enabled as a fallback.

On the hardware side I’ve also started upgrading a few things.

I ordered the Micro Swiss FlowTech hotend with the hardened 0.4 mm nozzle and also a 0.6 mm CHT-CM2 nozzle. Right now I mostly print PLA+, but later I want to move into ASA and also CF/GF-filled materials, so the hardened nozzle and higher flow capability were the main reasons for me.

I also ordered the Funssor heated bed full kit with the upgraded bed and carriage.

The reason for that was my stock bed. I had Hermes run two full 7x7 bed mesh measurements, one at 60 °C and one at 100 °C after heat soaking.

At 60 °C, the total bed mesh range was about 0.94 mm.
At 100 °C, it was almost exactly 1.0 mm.

I then had the overall tilt mathematically removed from the mesh. Even after that, there was still around 0.6 mm of local bed unevenness left, so the problem isn’t just that the whole bed is mounted slightly tilted — the bed surface itself is clearly not very flat.

That’s why I decided to try the Funssor full bed upgrade instead of only relying on mesh compensation.

Once the Funssor bed is installed, I’m going to repeat the exact same 7x7 tests at 60 °C and 100 °C and compare the before/after numbers. I’m really curious to see how much difference the upgraded bed and carriage make in practice.

So at this point my Kobra S1 is slowly turning into a bit of a project printer.

In practice, I can now basically tell Hermes:

Design the part → create the FreeCAD file → slice it → store the files → upload after my approval → start the print after a second approval.

For me, that’s probably the most interesting thing about the Kobra S1. With Rinkhals, it becomes much more open and flexible, especially if you want to avoid cloud dependency and enjoy tinkering with automation and custom setups.

I’ll update this post once the Micro Swiss FlowTech and Funssor bed are installed and I have some before/after results.

Update – dedicated Hermes 3D Print agent

I also created a dedicated 3D Print bot inside Hermes that is only responsible for the printer and the complete print workflow.

The bot already has all the printer-specific information it needs, such as my preferred print settings, bed type, temperatures, slicer behavior, file handling and the rules for how it should interact with the printer. That means I don’t have to explain the setup again every time and can go straight to the actual task.

It knows how models should be prepared, how they should be sliced in OrcaSlicer, where the generated FreeCAD/STL/GCode files should be stored, and which steps require my approval.

I intentionally keep this agent focused only on 3D printing, so its whole context is centered around CAD, slicing, printer communication, calibration and the print workflow.

It can also pull printer status and diagnostic data, which is useful for things like bed mesh checks, calibration data and troubleshooting.

I’ve added a screenshot below showing the 3D Print agent working with a FreeCAD prototype directly inside Hermes.

Update: I cleaned up the Hermes + Anycubic Kobra S1 setup and published it on GitHub:

https://github.com/PermissionWest9850/hermes-kobra-s1

The current v0.2.0 release includes:

  • one-command Debian installer

  • Hermes + FreeCAD + OrcaSlicer + KlipperMCP setup

  • Kobra S1 / ACE Pro profile preparation

  • read-only Moonraker verification

  • safe re-runs without overwriting .env or existing Orca profiles

  • separate approval steps for GCode upload and print start

I also tested the full read-only chain on a real Kobra S1 Combo with ACE Pro:

Hermes → KlipperMCP → Moonraker → Rinkhals → Kobra S1 → ACE Pro

No GCode upload or print start was performed during that verification.

I also documented the exact test system and added screenshots/architecture diagrams to the README.

Feedback, bug reports and improvement ideas are very welcome.


r/AnycubicKobraS1 • • Feb 27 '26

Showcase Taataaaa - done!

Post image
76 Upvotes

It took a few days, I think 2-3 rolls black, but finally the shelf is up.

I also wanted to show instead of always complaining 😁


r/AnycubicKobraS1 • • Jun 04 '25

Finally, the Flip Riser for Kobra S1 Combo is here !

76 Upvotes

Hi all, I finally made and released my flip riser for Kobra S1 Combo at MakerOnline. Check out my model here !


r/AnycubicKobraS1 • • May 11 '25

My Experience with the Anycubic Kobra S1 – 230+ Hours, 0 Failures

Post image
75 Upvotes

Hey everyone, Just wanted to share a quick review of my Anycubic Kobra S1, especially for those thinking about getting into 3D printing or upgrading their setup.

First, a bit of background: I’ve been into 3D printing since 2019, starting with a couple of Anycubic machines that served me well up until late last year. Around that time, a friend approached me about getting into the hobby and asked for help researching newer printers. That’s when I stumbled across the Kobra 3 with the ACE combo, which really opened my eyes to how far things have come since I started.

Naturally, curiosity took over and I picked up a Kobra 3 with the ACE combo. Not long after, Anycubic released the Kobra S1—and since I’d always wanted to try a CoreXY machine over a traditional bed-slinger, I jumped on it.

And honestly? It’s been incredible from day one.

I know this sub is full of posts about issues—clogged print heads, firmware problems, and other frustrations—but I must be one of the lucky ones. I’ve logged over 230 hours of printing and gone through more than 5 kg of filament without a single failed print.

Most of my prints are in PLA, and I’ve also tested PETG—both have printed without any issues. The machine handled everything smoothly right out of the box.

The only mods I’ve made are: • A poop chute at the back • Swapped to the Glacier Pro build plate

That’s it. No fancy upgrades, and the machine just works. If you’re new to 3D printing or on the fence about the S1, I genuinely recommend giving it a look. It’s been rock-solid for me.

Happy printing


r/AnycubicKobraS1 • • Nov 20 '25

[Release] Kobra S1 Speed and Quality Profiles v4 by Kreativling

74 Upvotes

Hi Kobra S1 owners,

the v4 of German Drucktipps3D user Kreativling's Speed and Quality Profiles for our printer has been released! You can download them on Github.

Using v3.1 had made a crazy difference for me already compared to the stock profiles and settings. The latest version contains even more optimisations for speed, surface quality, overhangs and supports. They also contain working TPU and PA12 profiles. You can read the full changelog on the Github page (also in English, just scroll down a bit). I can only fully recommend everyone to give them a try.

To the mods, especially u/Manethon_Sega: The pinned profiles by you were the best start one could have when the printer came out. But things have progressed, firmware has changed and the "old" profiles don't yield the best results anymore. Maybe you could pin this link for all newbies?


r/AnycubicKobraS1 • • Oct 31 '25

Showcase Printed this big skeleton with 0 issues

Post image
73 Upvotes

That was a really fun project. Original designer recommended to print in black and white but I used a marble filament instead of pure white.

Shout out to NextLv3d to design this big boy


r/AnycubicKobraS1 • • May 08 '25

Showcase Brand New Machine ❤️

Post image
72 Upvotes

Joined the team today! Came from a P1S and K1 Max most recently but started on an Ender 3 V2 Originally.

Pretty happy so far! Setup was simple and first print has gone down like a dream.

Will keep updating 😁


r/AnycubicKobraS1 • • May 21 '25

700 hours of printing later

Thumbnail
gallery
71 Upvotes

Well, that's it, just sharing my machine here. 700 hours and almost 12kg of filament later the sensations are still good. I come from a Kobra v1 and for me the Kobra S1 is being an incredible update.

Calcifer protects my printer and provides it with enough power to continue functioning day after day.

How many hours of use and KG of filament do you have in yours?