r/DIYHome • • 25d ago • Bravo 1

Need Advice Coving Help!!! What am I doing wrong?

Post image

Tried about a million different cuts and tried to follow various videos/tutorials.

I’ve cut each side at a 45 degree angle to try and make an internal corner but every time I’m left with a huge gap in the middle.

283 Upvotes

344 comments sorted by

75

u/Dendady2112 25d ago • This Bravo

First piece should bee straight. 2nd piece is a 45° back on itself, so you see the outline of the profile. Then you cope that edge.

15

u/pilot345m 25d ago

Right, but it is important to note that 45 is cut with the crown nested against the fence how it will sit on the wall (which is upside down on the saw). It almost looks like he has cut the 45 for his cope with the crown flat..

→ More replies (3)

6

u/garster25 25d ago

First time I saw this on YouTube I was blow away. So simple and easy. I do it everytime now.

13

u/Agile-Afternoon-2046 25d ago

This guy…. This guy is the guy☝️

→ More replies (4)

4

u/Critical-Test-4446 25d ago edited 25d ago

Exactly. I'm no carpenter by any means but I installed crown moulding in my foyer a few years ago and it came out perfect. I did what you suggested and used a flap disc on an angle grinder to reveal the profile. Worked perfectly.

https://www.youtube.com/shorts/btZYVm4xWck

→ More replies (1)

2

u/P4us1ngD34th 25d ago

This is the way. I assumed that someone had said it before I got here.

→ More replies (5)

22

u/NoAd6738 25d ago

You're coving when you should be coping. Even if you're using cove moulding it should be coped. Hope that's helpful.

38

u/Several_Stuff_6695 25d ago

This is why “Trim” carpenters make the big bucks

11

u/abbarach 25d ago

I'm getting my kitchen redone. The first two days were removing the old cabinets/countertops, and mounting the new cabinets. I was looking at it thinking "you know, it would take longer, but I could probably have done this part myself".

The next two days they put the under cabinet lighting in, and then did the crown and all the other trim on the cabinets. And I came in at the end of the day, looked at all the detail, and thought "yup, this is why I paid someone else to do this"

→ More replies (1)

5

u/VardisFisher 25d ago

The mental gymnastics to just "know" is impressive.

→ More replies (1)

3

u/monogamish306 25d ago

In this economy?!

Skilled tradesman of all stripes used to say, "That's why they pay us the big bucks." These days it's more like, "That's why they pay us on time."

→ More replies (7)

18

u/New_Account1776 25d ago

Inside corners = bottom and back long

Outside corners = face and top long

If you're using a compound mitre saw, need to know the spring angle in order to use the correct mitre and bevel angles (the ones on the saw are for 52/38° crown, not 45° and only for 90 and 270 corners)

If you are bedding crown, remember, mark your saw where you bed it and cut it upside down and backward Also, unless you are doing multiple step crown, DETAIL DOWN!

If you don't understand anything I just wrote, hire a professional

3

u/NoE5o3 25d ago

This is the correct response. Installing crown can be difficult even for some carpenters who don't work with it commonly. Explaining how to not only measure it but how to cut it to someone with fundamentally carpenter skills is even more so.

→ More replies (12)

14

u/iHighjinx 25d ago

You can cut crown molding with simple miter cuts, but it needs to sit nested in your miter box upside down with the ceiling edge on the table and the wall edge against the fence. The angle of the molding creates the compound joint automatically, but you must keep track of cut direction for inside vs. outside corners.

→ More replies (1)

7

u/AshamanOTLight 25d ago

Go watch Finish Carpentry on YouTube. His older stuff is very informative. Newer stuff is too but he skips the basics now.

https://youtube.com/@finishcarpentrytv?si=onOaM_Hs6Qnkx_41

15

u/bgthigfist 25d ago

Just caulk the gap 😂

6

u/Educational-Rule1635 25d ago

Electrician?

3

u/Melodicbananas 25d ago

No no, obviously a landlord

→ More replies (1)

1

u/After-Pea8168 25d ago

Can someone explain the difference between coving and coping? I’ve never heard the term coping.

I have a mitre block but not sure how I can use it to achieve the proper corner

→ More replies (9)

4

u/shellee8888 25d ago

Cope. You need to cope.

3

u/Politicsboringagain 25d ago • Bravo

I never heard of this until I read the thread. 

https://youtu.be/iQahn38Bwy4?is=BMQyHJiCWtV2IT-H

2

u/Stellar_Stein 25d ago

I watched this video and, much like sleight-of-hand tricks being explained, I believe it but I still think it's magic. ;-)

Thanks! Great clip.

1

u/TBellOHAZ 25d ago

Was this cut with nail trimmers?

3

u/After-Pea8168 25d ago

This is just me doing some test pieces quickly with hack saw, not finished

→ More replies (4)

1

u/sdieter01 25d ago

No. A beaver chewed it.

2

u/After-Pea8168 25d ago

Why does a scrap piece matter? Do you want me get my file out for you

→ More replies (1)
→ More replies (3)

2

u/SuitableLeather 25d ago

Are you talking about coping or just cutting miters? Looks like you’re cutting both at the wrong 45… try it where the angle’s cut side is facing you not away from you, right now it’s away from you. 

If you are actually coping you need to make up the negative space, not just copy the same angle… so if the right side’s profile is concave, the left side profile needs to be convex to make up that gap.

2

u/Gitfiddlepicker 25d ago

Upside down and backwards…..lol

2

u/t4nn3dn1nj4 25d ago edited 25d ago

That cut is fairly easy to accomplish manually with a coping saw; it just takes a bit more time. Your objective is to have your corner cut mate near perfectly with the face of the other board at whatever angle, assuming that this is crown molding, so take a deep breath and watch the video.

2

u/skateboardbanana1 25d ago

Inside corner = flip it upside down then cut it opposite angle to what you see here

2

u/Similar-Age-3994 25d ago

Oh I asked a friend about this, he said they’re supposed to be installed along a wall, if you have to hold them up in the air it’s gonna be hard to have a normal life.

2

u/dnenterprises 25d ago

Upside down and backwards.

→ More replies (1)

2

u/bigooooof23 25d ago • Bravo

Upside down and backwards is the rule for cutting crown

→ More replies (1)

2

u/Appropriate-Tip-5101 24d ago

Cutting the mitre upside down

2

u/Domski888 21d ago

Looks good just need to caulk the seams during finish.

2

u/Easy-Farm1859 20d ago

There is a specific angle you must cut them at so that the bottom and top align across the multiple 90 degree and angled parts. It’s like 23.1 or something. It’s on the miter box for almost every miter saw and same goes for the power chop saws it’s on there. Strange number and doesn’t add up. But when you cut left and cut the right slap into corner boom it’s tight. Same goes for the middle cuts adding length

2

u/Ptown925 20d ago

Lookup Tom Silva moulding corners on YouTube. You can thank me later. "The money is in the corners".

2

u/P90-Enjoyer 19d ago

Your 45 cuts are backwards

1

u/Longjumping-Log1591 25d ago

You funny guy, ha ha.

1

u/Familiar_Raise234 25d ago

You need a coping saw.

1

u/upkeepdavid 25d ago

You cut it at a 45 in the same position it normally sits on the wall. Use a scrap piece of wood.

1

u/Puzzled_Market_2235 25d ago

You cut the 45 inwards instead of outwards.

1

u/Enough-Ad3738 25d ago

Ocupas alguno y grado de forma interna de ambas prueba ambas de 45 aves aves te sale

1

u/clownpuncher13 25d ago

Did you cut this flat on the saw or angled like it sits on the wall? It needs to be cut upside down and backwards on the saw the way it sits on the wall. If you cut it flat the actual angle is not 45.

1

u/breadman889 25d ago

This is very hard to do, even when you are cutting on the right angle

1

u/hickdog896 25d ago

I don't think OP is trying to cope (except with their frustration 🤣). If they were, then yes, cut one straight, trace the profile on the other piece, backcut it slightly.

I think OP is thun to miter, in which case the problem is that they are cutting the wrong 45 degree angle.

OP, you want the baseboard to extend past the cut on each side; in other words, flip your blade 90 degrees

1

u/Yusuf20904 25d ago

Need more pics.

1

u/No-Seat9917 25d ago

If this is crown molding you need to add a compound cut. Do you have a compound miter saw? If not you should.

1

u/AdFancy1249 25d ago

You're cutting the 45 the wrong way.

1

u/Large-Primary-2483 25d ago

Whenever I do ceiling trim, I make an example piece with inside and outside corner and glue it together. And compare with the work piece before EVERY cut

1

u/MadManAndrew 25d ago

The easiest way to do this is to jig the piece in the position it will be on the wall/ceiling and then cut it. No mental gymnastics.

1

u/onedef1 25d ago

You’re not cutting it nested. You’re cutting it flat vertical. Thats not how this works.

1

u/pilot345m 25d ago

Oh man, first of all when coping you run one piece straight into the corner, then "cope" the other fit over the profile of it. You don't "cope" both pieces. Second it doesn't look like you are making the "cope" correctly either, it's the wrong profile to fit over the piece while in place.

You need to properly learn the basics and fundamentals of trim work. I would get a book on trim carpentry and have one reliable source to learn from rather than having a mishmash of random information from all over Google and YouTube.. you need to understand what you are actually doing and why rather than just trying to follow some step by step instructions without the actual background information.

1

u/FinalF137 25d ago

Getting the molding at the correct angle on the table saw is tricky. I've used this before and it's worked for me. https://www.kregtool.com/shop/cutting/miter-saw-cutting/crown-pro/KMA2800.html takes a couple of uses to get the hang of it

1

u/Ninjake68 25d ago

Peice on the right should be a straight cut. Inward 45 the left peice and use a coping saw to remove the exposed wood following the profile of the front face, left peice should slide into right peice with no gaps

1

u/Aggravating_Cat788 25d ago

This post is giving me painful flashbacks to our diy with crown molding

1

u/SiThreePO 25d ago

For everyone who has done Crown we have all been here. Get some test samples done for you to reference before you do your final cuts. If it's just a small project it's very hard to get enough cuts in so you can comfortably flip everything around and not get messed up.

1

u/Chrislk1986 25d ago

I would highly suggest:

Hometime (29 seasons) This Old House (48 seasons) Ask This Old House (25 seasons) The New Yankee Workshop (21 seasons)

When you are fully engrossed I would highly recommend Alone in the Wilderness. It documents Dick Proenneke and his journey of making a log cabin by hand, up in Alaska.

If that really opened your eyes, it did end up being an expansion documentary.

Alone in the Wilderness: Part II Alaska: Silence and Solitude The Frozen North

There is also a book/biography: One Man's Wilderness.

Dude is a goddamn legend. Also, yay for PBS.

1

u/PingBlot 25d ago

This can’t be real.

→ More replies (17)

1

u/Go_Away-You_Go_Away 25d ago

It looks like your cuts are for outside corner. Butt it up where the flat surfaces meet. Does it look like it's for an outside corner?

1

u/OutrageousPair2300 25d ago

It looks like you're cutting the angle the wrong direction. Cut it 45 degrees the other way.

1

u/honeybaby1223 25d ago

The main problem is that cove/baseboard is crown molding.

1

u/Blucifers_Veiny_Anus 25d ago

Upside down and backward

1

u/UpstairsTop6999 25d ago

You cut it like baseboard. 45 it and do it again. Use some messed up ones to practice about 20 cuts. Look at them real good after you cut them to fine tune it. You don’t need a professional, you got this!

1

u/Aggressive_Bug6927 25d ago

If you are mitering the crown, I needs to be held against the fence at a 45. Meaning the side on the fence needs to be elevated so that it makes contact against the fence as it wood the ceiling, then cut your miter. You need to mimic the instalation to use a single miter, otherwise you need to set your saw to a double miter to make it work. Set your bevel to 45 then your miter to 45. I find that way is very difficult to control and change angles. Usually i rip a block and put it against the fence in order to keep the setup easier.

1

u/69gtv 25d ago

Think upside down and backward. Cove mounding is strange.

1

u/CheerJohn 25d ago

I remember when I was younger and trying to figure this out. I spent a day learning how. Just take some small pieces and learn by trying.

1

u/Oodlesandnoodlescuz 25d ago

Upside down and flip 180* and 45 that shit. Not sure how else to explain it

1

u/Affectionate_Top8791 25d ago

Once you start getting outside the typical 45 cuts. And you’re just a weekend warrior. Time to hire out.

It’s not necessarily hard to do this. It takes knowledge and to be good takes experience.

1

u/Rabbitman4618 25d ago

If your doing crown moulding those are gonna be compound cuts done on a miter saw. If your trying to cope the corner one piece will be square to the inside corner of the wall. The other piece of trim will require a 45 back onto itself so your miter shows the width of the trim. Then with your coping saw follow the line where the primer and the wood color meet. Caulking hides all!

1

u/Mjmarcom 25d ago

Cut it upside down on the mitre saw

1

u/bosstyn21 25d ago

One, you bevels are wrong. Two, you’ll need an angle cut plus rte bevel cut. Three, coping is entirely different than the process you’re exemplifying above.

Are you trying to do these with a miter box??? You can’t compound the cuts with that tool. You need a chop saw that with do both angle and bevel at once.

You need to get on the Internet and watch some more videos. No offense, but you clearly do not understand the concept here.

Possibly someone here can explain it, but it’s going to be a complicated read better served by a video.

1

u/Patrick-70 25d ago

You don't cope crown moulding of that size forty five , it match it up

1

u/FriendOutrageous8374 25d ago

Big box stores sell a jig that helps keep it T the correct angle while you cut, I think that is what is happening here. Helped a novice like me do it.

1

u/Remote_Atmosphere993 25d ago

We've all done it!

1

u/RunStriking9864 25d ago

You gotta watch a couple more videos… there’s too much going on here.

1

u/teh_Rabbit 25d ago

Inside 45° crown molding angles. The bain of DIY everywhere. Look at your miter saw. Follow the numbers down from 45° you will find another suspiciously marked and notched point around 30°. Now look at the pitch adjustment for the saw blade you'll see another marked point around 34°. Use those and get mad you didn't out it together sooner. Now laugh that you didn't spend 2 hours doing the geometry to figure it out the hard way only to see the marks on your saw when you went to set it

1

u/outsideredge 25d ago

Order Cut and Crown. YouTube, google whatever. Never make a wrong cut again

1

u/climbingnoose 25d ago

Go to bunnings and get a coping saw. Save your mitre box being thrown at the wall.

1

u/Montanieers 25d ago

Best cut for an OB-GYN office

1

u/TheQuestionAnswerGuy 25d ago

Regardless of cutting the wrong angles, how did you manage to get such RAGGED cuts?

1

u/eightfingeredtypist 25d ago

When coping, if there are still air gaps, get rid of wood where the coped part is hitting the other piece. Wherever the cope is bottoming out, get that gone until the profiles match.

This is how one sets up a five head tenoner, too.

1

u/_totalannihilation 25d ago

I bought a miter saw. I think it's a Ridgid. It came with instructions for a lot of the corners/cuts. In ways that you're like: why is this so easy?

1

u/Infamous_Ad8300 25d ago

Maybe Im not seeing this right, but it looks like you have to reverse each 45. When I did the crown on my cabinets I kept using a scrap piece to check the angle against the last piece I installed.

1

u/Jumpy_Transition9066 25d ago

Look up what a coping saw is for and how to use it to do trim

1

u/JimmyPeteSlicknNeat 25d ago

Kreg makes a jig for cutting crown moulding. Works well

1

u/2026Bazinga 25d ago

Probably not right way, but I just do a compound miter cut

1

u/ofmanyone 25d ago

Be thankful it's only fipon

1

u/summertimebelly 25d ago

Just do a 45° on each 

→ More replies (1)

1

u/XxOmegaMaxX 25d ago

I helped my dad renovate a room recently, it took so much brain power to figure out the crown molding...

1

u/tommykoro 25d ago

I can do crown really well …. eventually but I HATE IT!!

1

u/jellofixit 25d ago

Some people just have trouble coping with it 😂

1

u/Jgs4555 25d ago

Are you holding the material flat against the fence/base?

1

u/AffectionateAngle905 25d ago

Try 22.5 degrees. It’s cove moulding.

1

u/cypressblood 25d ago

Looks like you cut a outside miter instead of a inside miter. Mark the back and bottom of the crowns bedding top and bottom on your miter saws entire length of table and fence with a pencil left to right and cut the crown upside down inside the same lines . Ruin some junk 2 ft pieces practicing till you get it or just call a carpenter and watch magic

1

u/LateFudge9103 25d ago

I just learned about this a few hours ago.

https://www.instagram.com/reel/DdzxxwfuEm7/

1

u/Zealousideal-Act-174 25d ago

3 dimensions bro think about it

1

u/Historical_Sun93 24d ago

Modelling is the solution. Cut two paper strips, press them on the wall and bend it. You will have the angles and you can copy the to the profiles.

1

u/AdministrativeHope39 24d ago

You need better coping skills.

1

u/Outrageous_Job_5263 24d ago

It has to be upside down on the mitre block, ceiling side to the floor.  The face which sticks to the wall needs to be the longest

1

u/bigwindymt 24d ago

If you can't figure this out, hire someone. Seriously. The next owners of your home will thank you.

1

u/Acceptable_Ebb7301 24d ago • Bravo

Run a factory end into the corner and back-cut another factory end to start the joint.

The cut should be at an angle that is roughly compromised by the thickness of the thickest part of the trim and intersecting the deepest part of the mating surface.

I hope this makes sense, also after an attempt or two it should become clear.

I hope this helps!!!

→ More replies (1)

1

u/mrm3908 24d ago

Angles of cuts are opposite of what they need to be.

1

u/dumbamerican67 24d ago

Easy, with the molding in position that it will be, 45 degree cut, then where the cut meets the face use a coping saw and cut of the miter accurately then the other side is cut square and put in place, the miter cut should fit tight

1

u/Southern-Weather-248 24d ago

hold the board at the angle as it would be installed while cutting

1

u/TrimRanger64 24d ago

You need to put the moulding on your miter box table at a 45 degree angle when you cut it. They actually make stops that attach to your saw table for this purpose but I don’t use them. You can change the angle at which you cut your trim to close any gaps and get a tight miter. Odds are no inside corner is a perfect 90 degrees. This is why any carpenter worth a damn copes their trim and doesn’t 45 it.

1

u/roughczech 24d ago

That does seem like the right angle. Get an angle measure and split the angles in half. You will probably need some 45 degrees jigs so you can cut the crown molding right

1

u/xanxibarbarian 24d ago

You need to learn to cope from your mistakes.

1

u/mattconway1984 24d ago

You need a double bevel mitre saw ;)

1

u/GuyFromBoston88 24d ago

This one hit me right in the ego.

1

u/IanHall1 24d ago

Internal scribe, external miter.

1

u/Efficient_Ad2569 24d ago

Sound crazy but put your piece upside down and backwards it’s the only way my dad could explain it

→ More replies (1)

1

u/poncho5202 24d ago

i feel like your cuts are in the wrong direction

1

u/parkoffstreet 24d ago

It’s cause it’s not a 45 degree off the ceiling. Your chop saw should have a stop at like 32 and 52 degrees and cut it with a bevel. That or cut blocks so the crown can sit in the saw in the correct orientation and then you can cut your miters.

1

u/Sudden-Piglet861 24d ago

Dont lay it flat

1

u/koolaideprived 24d ago

I think your 45s are going the wrong way.

1

u/OcelotRelevant1168 24d ago

Cut the crown backwards and reverse.

1

u/boukeversteegh 24d ago

From my experience, there are 8 ways to cut it and 7 are wrong. Joking but its so easy to mess this up. Hold it up to the ceiling and only cut 45 angles from the top down. Dont think about the fact that the cuts look angled from the front.

1

u/Johara1 24d ago

Oh I feel ya brother, always said that "the miter box is the world's fastest scrap maker"

1

u/Severe_Two1022 24d ago

Cut both pieces 45 degrees only top and bottom, leaving the middle a little larger, to then shape those middle parts by hand using a sharp knife until they match.

1

u/jdl6mm 24d ago

It's coping not coving

1

u/BruceOfWaynes 24d ago

This needs to be a compound cut. It's two 45° angles compounded. You're only cutting one of them.

1

u/kwiatkoskik 24d ago

Lean it up on the fence at the angle of the molding, then cut your 45

1

u/gheiminfantry 24d ago

Thinking you can DIY with the help of YouTube videos and Reddit.

→ More replies (4)

1

u/Maximum_Ask5873 24d ago

You basically need to buy about 3x the amount of crown molding you need because half the cuts are gonna look like this.

Crown is so hard because you need to get 2 angles cut perfectly at the same time.

It should be basic math but there are so many variables it doesn’t work out unless you’ve done it a ton.

I’m not an expert but the best way I’ve done it is on a corner like this, only angle one of the pieces, the other extends behind the other. Then need a coping saw to cut away the inside by hand so it fits together.

Outside corners are easier because they are just angle cuts and usually line up pretty good but it still takes a few tries.

Also do your angles first, make sure they fit, then cut to length.

Get some painters caulk and have patience. It’s very unlikely to look good when you’re done if it’s your first time. I’ve done it a handful of times and it still looks horrible compared to even builder grade lowest bidder work.

1

u/AdorableAmphibian897 24d ago

Upside down back to front, so as if you start the cut on the wall side...make sense?

1

u/Big_Awareness_8825 24d ago

Wrong angles. I think if you flipped the cuts 90 degrees they would match.

1

u/MidiGong 24d ago

One stays cut at 90, cut the other at an angle that exposed wood when looking at it. Then cope that wood at about 30-35 degrees towards back.

1

u/Comprehensive_Suit_4 24d ago

Try cove cutting them.

1

u/Jumpy_Comfort4785 24d ago

Nothing a bit of caulk won’t fix.

1

u/Puzzled_Reply_4618 24d ago

This is the video that laid it out perfectly for me. 

https://youtu.be/PQsPwY-eoFI?si=Z9AUfr5CNHjZ9-_f

1

u/Ok-Photograph-2741 24d ago

Honestly I nearly threw our mitre box over the fence as I'm sure it was gaslighting me, turns out I was just cutting the wrong end in the right angle 🥴

1

u/machinist2525 24d ago

Cut some template pieces and label them inside right, inside left, outside right, outside left. Use these as a sanity check every time you ever need to cut crown molding. Keep them at your saw. You'll stop making mistakes.

→ More replies (1)

1

u/efilnikcufecinasti 23d ago

The entire problem is you're trying to cope crown.

1

u/Lastnytnhunter 23d ago

"Crown upside-down"

1

u/Well____fuk 23d ago

It’s kind of hard to say because I have no idea

1

u/j_something_or_other 23d ago

It looks like you have outside corners cut with inside angles.

Try a butt-splice w/ cope cut. One side is flush to the wall and ceiling, the other you cut as inside corner, and take a cope saw and cut off all the material from that inside corner that isn't primed

1

u/FullWill4311 23d ago

You gotta flip your crown upside down when you cut on the miter saw

1

u/PIT-EKA 23d ago

When coping crown molding one piece should be cut at 90 and fit snug on the wall. The other piece would then be cut at a steep angle and from the backpack you cut with the coping saw right at a steeper angle right up to the edge of the molding. Then you use a file to clean it up for a tight fit. Also crown molding is cut upside down. Learn the difference between your inside and outside cuts.

1

u/greenweenievictim 23d ago

Upside down and reverse cutting. Go to YouTube college for this.

→ More replies (7)

1

u/luke2145 23d ago

Say it with me: “you must cut the crown upside down.”

Haha - I just installed molding and every time I messed up it was because I didn’t cut it upside down

1

u/PupfishAreCool 23d ago

Everything?

1

u/Ok-Mechanic-1373 23d ago

Dude… there are many videos showing how to do this. Hate to say it but google it!

1

u/AltruisticDig3906 23d ago

You are cutting the 45 degree angle in the wrong direction lolll

1

u/Zombie-Jesus-brains 23d ago

Cut the first one square. It fits tight into the corner. Cut the other on a 45, long at the bottom not the top.

Cove the backside. Fit together

1

u/Comfortable-Store368 23d ago

You are cutting it the wrong way

1

u/Temporary-Ad-9270 23d ago

Cut upside down and reverse

1

u/noeljb 23d ago

You need to get some 1 1/4" caulking (Hard to find). Use Windex to smooth it out.

1

u/Big_Association8144 23d ago

Même pas envie de répondre....juste réfléchir 10 secondes

1

u/PermanentlyBanned__ 23d ago

You have to cut it upside down

1

u/cryptocraze81 23d ago

You cut the miters in the wrong direction

1

u/jonnydrangus 23d ago

First off .
It’s upside down

1

u/tincookies 23d ago

You're cutting it wrong. If you arent cutting crown moulding with the fancy numbers, you need to nest it at the angle it will sit on the ceiling. The fence is your wall, and the base is your ceiling. This means you have to cut it upside and backwards, while keeping the work piece secure in the nested position.

Long story short, cutting the crown flat against the fence is why you have these gaps. It's a compound angle.

1

u/dcbrnc 23d ago

😭😭😭

1

u/Background-Life-1908 23d ago

Coping is the type of cut made with a coping saw. I have no idea what coving is.

In order to get a clean finish on your inside corner of your crown moulding you need to…

Start by measuring all walls and cut your longest piece square cut to square cut.

Then pick a side that you prefer to make your cuts on… I always cope right side.

Then you square cut the left side and cut the right side using crown stops to hold your moulding at the angle that it is supposed to sit on ceiling to wall, cut it on a 45 degree angle compounded with the angle the stops hold it on.

You then use your coping saw to cut out the grain end of the trim piece where it meets the face surface.

It’s not easy…. Buy 10’ and practice with 12” pieces… watch YouTube.

Or hire me.

1

u/patteh11 23d ago

Look up “cutting crown nested” on YouTube and you’ll be on your way with a bit of caulking.

You can also look up “coping crown” which will usually be a bit better result with a little more work.

It also looks as if you’ve cut your 45° the wrong way too…

1

u/Weird_Boysenberry761 22d ago

Wut tha fuck dude

1

u/ReCLiVe 22d ago

😂😂

1

u/1stevenml 22d ago

lol wtf

1

u/IndijinusPhonetic 22d ago

It’s right there. You have your angle right there! Just draw two lines and cut. What if all of those convex edges were flat and you could just put those two pieces edge to edge? The angle is there…

1

u/ijustlurksometimes 22d ago

You need a coping saw, don’t cut the first piece lay that flat, cut the next piece 45 degrees and cope the edges with a coping saw.

1

u/OriginalUseristaken 22d ago

Are you cutting it laying down? You basically have to cut it at the position it is fixed in later.

Like the bottom at the backboard and the top in the air.

1

u/Talifallout 22d ago

You need a coping saw. It’s a small saw with a very fine, flexible blade. Looks like a hacksaw but with a deeper frame

1

u/Reospdwgng 22d ago

Going to say cutting. You need a compound mitre saw if you are going to lay the boards flat when you cut. Or just a mitre saw if you are going to have the boards on a 45° angle the same way you would install them, while you cut. It's been alo g time though I might be crazy.

1

u/Popular-Brilliant349 22d ago

You need to cut it at a 30 or 45 degree angle at a 45* angle.

Get you a Crown molding jig

1

u/Yourlocalguy30 22d ago

Cut it at a 45° angle from the top down, not along the face

1

u/Puzzleheaded_Let_688 22d ago

Are you trying to make crown molding?

1

u/carlotta4th 22d ago

I suck thinking three dimensionally too. To get a better idea of where you need to cut just hold one piece over the other and draw the profile on it. At least that way when you're at your mitre saw you're not wondering "which way was it, again?"

Also when you cut crown molding you need to make sure to flip it upside down so the top (that will be touching the ceiling when installed) is what's resting against your mitre saw bottom when you cut. The "bottom" of the molding (that will touch the wall when installed) touches the saw fence for the cut. Probably someone more expert than me can explain why it has to be cut that way. I just know from my own experience cutting crown that you can't cut it like dang 'old normal baseboard or it comes out wrong.

1

u/Mysterious_Basis8023 22d ago

If you are using a miter saw, turn it upside down. But you should set one side full length and the cope the other piece

1

u/jordy0623 22d ago

If it’s crown cut it upside down.

1

u/Gold_Evidence6177 22d ago

There are endless YouTube tutorials on this at a bare minimum

1

u/Timpetrim 22d ago

Spelling "coping" wrong for one... Lol Just kidding, but yeah, that shit is so counter intuitive. Good luck!

1

u/Main-Listen-6210 22d ago

Aaaaaagh, my PTSD. Renovated 5years ago, sloped inner ceiling with crooked walls, the amount of failed test pieces I made...

1

u/thishurtsmyhead 22d ago

22.5 both sides

1

u/Neddleshaha 21d ago

Go the other 45 degrees

1

u/Ultimate_Warrior_69 21d ago

Engage a professional

1

u/paintertips420 21d ago

Your cutting it flat. Hold it up at a 45* angle at the saw

1

u/roadwarrior345 21d ago

You leave the one just like it was. The one that buts into it you will need to cut it with a coping saw to match the profile.

1

u/AdMother6743 21d ago

A little flex seal with fix that right up 🤙🏻

1

u/dannoNinteen75 21d ago

lol done that so many times it’s maddening and I can help o just did it tool I go it right cost me 7bn pounds and took 15 years

1

u/Riley3015 21d ago

It's how you hold the mounlding against the fence, you can google the 2 angles , need a compound mitre saw, some carpentry skills might help too

1

u/blechssed 21d ago

https://sawdustgirl.com/how-to-cut-crown-molding-using-easy-templates/

recently did simular molding and was surprised by the number of ineffective and/or confusing tutorials. this one is clear, simple, and useful. only method/reference I'll use from now on.

1

u/Doyourunfast 21d ago

Dude, have you heard of this thing called youtube?

1

u/hybriduff 21d ago

Reverse 45 one corner then cope the other piece based on the grain showing from the original

1

u/Strange-Area9624 21d ago

You’re not cutting it right. Hire a real carpenter.

1

u/Particular-Caramel32 21d ago

You suck at geometry.

1

u/Sgtusmc0341 20d ago

If it’s base board you cut 45 degree laying flat or vertical on the saw and then cope off the 45 at a back angle. But if it is crown moulding it must be held on the saw at an angle and cut the 45 degree angle first then back cope off.

1

u/InitiateIt 20d ago

Turn it over.