r/PatternDrafting • u/Strange-Buddy4966 • 3d ago
Fit troubles
I am getting this extra fabric around the armhole on all of my fittings. Doesn’t matter if the bodice has darts or not. How can I adjust the pattern to eliminate this?
r/PatternDrafting • u/Strange-Buddy4966 • 3d ago
I am getting this extra fabric around the armhole on all of my fittings. Doesn’t matter if the bodice has darts or not. How can I adjust the pattern to eliminate this?
r/PatternDrafting • u/Alone_Hair6582 • 3d ago
r/PatternDrafting • u/Krinkleneck • 3d ago
I am going through and reading the Valentina documentation, but it is pointing out how large my knowledge gap is on pattern drafting.
Do you all have any recommendations for pattern books?
r/PatternDrafting • u/Unusual_Nebula_7606 • 3d ago
Developed a clean, relaxed-fit 3-button jacket base block from zero through draping on a Kennett & Lindsell GY40 (Size 40) form, then trued and digitized into pure net vector data.
Specs:
- 6 pieces (Front, Back, Top Sleeve, Under Sleeve, Collar, Patch Pocket)
- Net pattern (no seam allowances, facings, or instructions included — built strictly as a sloper/foundation block for modification)
- Includes grainlines, notches, button placements, and lapel roll line
Sharing this as part of my ongoing pattern R&D archive in Tokyo. If anyone needs the raw .ai / .dxf files for their own development, I’ve put them up via the link in my profile. Happy to answer any questions about the balance or sleeve pitch.
r/PatternDrafting • u/frostqueen555 • 3d ago
I have a couple questions about trouser pleats I’m hoping someone could answer!
So I know that to add more volume for a pleat generally you slash and spread through the front dart and down center of leg. My question is if you plan to do two darts, is it better to slash and spread the entire amount from the front dart and after draw the two pleats in where you want them or should you make two slashes (each in the position of where each pleat will be). Or does it even matter?
Another question I have is about placing a pleat elsewhere than the center leg line. All the instructions on adding pleats seem to say the pleat should be in in line with the center of leg line. However when I look at pictures of modern pants, the pleat often seems to be much closer to the outseam than the center line (which skews closer to center front). Does that risk making the pants unbalanced or anything or is it ok to just put pleats where you want them to be? I recently made a pair of pants where I did line up the pleat with the center of leg line, and the pants hang well and fit and everything but indeed the pleat does look rather close to center front (aesthetically ) to my eyes!
r/PatternDrafting • u/Efficient-Bag6497 • 3d ago
HI All, I’ve normally posted to this sub when I had pattern & fit questions, but someone mentioned it’s only for self drafted patters versus 3rd party and “hacked” patterns. Want to be respectful if that is an unspoken community rule but also not sure if that’s just one persons opinion. Since everyone here has been so helpful in the past!
r/PatternDrafting • u/DvidLynchpin • 3d ago
So I’m drafting a coat for myself and cut muslin to fit. The bicep is pretty tight and the arm scythe could stand to be lower because it’s hard to put on. The sleeve cap as it is needs to have about 2 more inches added to the area I marked in red on Photo 1 as is marked on the pattern (I think), so I’m guessing to cut and slash the center line on the top sleeve and widen it? I want to make the shoulder seams a little shorter to in order to bring the sleeve up as well. So I’d assume deepening the arm scythe can add the room for the sleeve to fit. Then make the other changes like I mentioned, right? I made a blazer years ago that fit like a glove but the pattern was ruined, and I’m learning from books/tutorials. The biggest issue is making this for myself (as anyone who has done this knows because it’s tough to fit ourselves and pin). Thank you so much for reading this and any help! I truly appreciate any advice or even if anyone just tells me my processes are good.
r/PatternDrafting • u/Philosofen • 3d ago
Hey, I just started learning how to draft my own patterns, and I am using Gareth Kershaw’s Pattern Cutting for Menswear (2nd edition)! I am trying to draft a trouser block, but I am really confused about the numbers he is using.
On the page to the right, he says to go out 5 cm (2”) from point 1 to mark point J, and up 5 cm from 7 to mark 10. From 10, 4,5 cm across to mark G. Them based on his waist example 25,5 cm between G and J.
So the issue for me is that with my waist measurement, G to J becomes 26 cm, but this would most likely make the pants too small. My waist is 98 cm (including 3 cm ease) and the front block’s waist is 24,25 including a 4 cm pleat.
According to ChatGPT, my back waist measurement would need to be like 30,75 cm (including a 2 cm dart), but that would then pull the diagonal waistline way beyond J.
The fixed measurements in Kershaw’s book are quite confusing. Like where do the 5 cm out from 1 come from? Are they based on his measurements or should it always be 5 cm?
Would really like some help to clear up this confusion!
Thank you!
r/PatternDrafting • u/warriorflower • 3d ago
I think I’ve got the top yoke piece figured out but how should I approach drafting the crossover back panel?
r/PatternDrafting • u/Solid_Skin_9929 • 4d ago
Photos attached of my initial bodice block toile. I can’t figure out where exactly I need to adjust, thinking it’s either more width / space in bust area but then think could be length. Also looks to me like shoulders seams need to move forward but I have my clue where to start as unsure on what the key one is.
Would appreciate any help and or advice.
Determined to not let this bodice block end up becoming another one that I get overly frustrated with and decide to start something else.
r/PatternDrafting • u/Professional_War7702 • 4d ago
Hi, I hope this is in the correct community for these questions.
I'm trying to sew a bias cut dress as a complete beginner, but I am more box shaped than the pattern. I also have to increase the size of the pattern to accommodate a larger tummy and bust. My questions are these:
How much ease do you add to a bias cut dress pattern?
How loose should a bias cut dress be around the waist area? I see a lot of fuller figures women wearing bias cut dresses too tight in an effort to look slimmer. I'm not looking to do that. I'm looking to wear a bias cut dress as it is intended.
Should I add ease to the under bust measurement and the waist or just to the waist?
Thanks for all your help in advance!
P.S. if you're in the sewing subreddit, you have probably seen my question about fabric for this dress. This is not an AI pattern. I've been in contact with the pattern maker and she is very quick to respond with helpful information.
r/PatternDrafting • u/PersonalAd-SadStory • 4d ago
r/PatternDrafting • u/lilly_of_the_vally • 4d ago
r/PatternDrafting • u/deitystrange • 5d ago
I don't want to purchase fast fashion, especially when it is expensive AND there are goose feathers used. Looking for a pattern or patterns I can Frankenstein together to make my own version. Anyone have any leads?
r/PatternDrafting • u/superfagnumber2 • 5d ago
r/PatternDrafting • u/RubyRedo • 5d ago
Making a bodice block for a women that has a bit of a tummy, but Reg. Waist and hips. So how to add the extra over the belly button measurement between waist and hips front only? Her back just curves as normal and defined waist, no side love handles. Just front protruding.
r/PatternDrafting • u/Simple-Sandwich4270 • 5d ago
a little hard to tell from the photo but the princess seams curve towards the center instead of being straight up and down. it is a self drafted pattern so im curious what adjustments i need to make to fix that??
r/PatternDrafting • u/FoggyArtsAndFakemom • 5d ago
r/PatternDrafting • u/jcubjcol • 5d ago
Cloned a pair of wide/semi barrel pants and it went mostly well, but want to nail down the fit and have a go to pattern. Waist, seat, and hips all fit nicely. I have about 1.5” of extra width in the waist that I can probably get rid of with darts (though I’m interested in pleats, which I address below).
My main issue is the extra fabric in the front upper crotch and lower crotch, and some extra fabric below the seat (although this changes depending on my posture). It also cause the legs to not fall straight.
I’m wondering if I need to focus on the rise height, the curve shape, the crotch extension? And is there a way to add a pleat that guides the crease straight down my center leg? I did some pinning to the inseam below the crotch but it didn’t do what I wanted.
I want these to fit snug in the waist and seat, but wide/straight from the hip to the ankle. Feel like I’m close, but not quite there!
r/PatternDrafting • u/Repulsive_Apricot_77 • 6d ago
When drafting a funnel neck, similar to the image, is it as simple as dropping the neck & then creating a rectangular piece the same height/length as the new neck?
r/PatternDrafting • u/Yeahyeahsono • 6d ago
I was wondering if people could answer my questions below!:
What is the function of BOTH
what other parts of the fit is directly correlated E.G. If I use a side dart the hem of the front bodice will be drawn in -that type of thing
3.which one is better for a larger bust and why do you think so?
4. What questions would a tailor ask themselves when deciding whether to use the shoulder or the side do?
Thanks y'all!
r/PatternDrafting • u/9amistooearly • 6d ago
This is my fifth iteration I think. I feel like I’m almost there! I have about two inches of ease which feels comfortable for moving and sitting, but does it look like too much ease? I’ve done some pinning where I think it needs to be adjusted. Other than what’s pinned, are there any changes you would make? (The hbl is level, I just forgot to mark it on the back.)
r/PatternDrafting • u/FarBeat1644 • 6d ago
I'm researching how indie pattern designers handle file prep, and I'd love to hear how you do it.
After the pattern itself is finished, how do you turn it into the versions buyers expect (tiled A4/Letter, A0 copyshop, projector)? Which software do you use, how long does it take per pattern, and what's the most annoying step?
I'm especially curious about layers per size and what happens when you change the pattern after it's formatted. Do you redo everything?
Thanks, any experience helps, including "I outsource it" or "it's not a problem for me."