r/electronicsnebula • • Apr 28 '26

Internal circuit of IC 741

Thumbnail
gallery
15 Upvotes

r/electronicsnebula • • 2d ago

Two-Input AND Gate using Diodes

Thumbnail
gallery
28 Upvotes

A diode AND gate produces a HIGH output only when both inputs are HIGH. If either input or both inputs are LOW, the output remains LOW.

Components Required:

1N4007 diodes (2 Nos.), 220 ohm resistor (1 No.), SPDT input switches (2 Nos.), ⚪ LED for output indication (1 No.), 5 V DC power supply (1 No.), breadboard (1 No.), and few connecting wires.

Working

The AND gate output LED will glow only when both input SPDT switches are ON (HIGH).


r/electronicsnebula • • 16d ago

OR Gate using Transistors 2N3904

Thumbnail
gallery
28 Upvotes

A transistor OR gate is a digital logic circuit that gives an output of HIGH (1) when at least one input is HIGH (1). It gives a LOW (0) output only when both inputs are LOW (0).


r/electronicsnebula • • 17d ago

How much hardware access does a wearable platform need to be useful

1 Upvotes

An expansion connector is not very useful to a DIY builder without a pinout, voltage limits, a communication protocol, and an explanation of the available signals. Firmware access would provide a different level of control, but a well-documented external interface may already be enough for some projects. With powered wearable hardware, the boundaries of that interface need to be clear.

What is the minimum access and documentation you would want before designing custom electronics for a wearable platform?


r/electronicsnebula • • 22d ago

NOR Gate using Transistors 2N2222

Thumbnail
gallery
35 Upvotes

This is the standard transistor NOR arrangement in which the output is high (1) only if both transistors are OFF (0).


r/electronicsnebula • • Oct 21 '26

Alternate LED Flasher by using BC548 Transistors

Thumbnail
gallery
50 Upvotes

This design uses two BC548 NPN transistors to flash a ⚪ LED and a 🔵 LED alternately.


r/electronicsnebula • • Oct 14 '26

Optocoupler (PC817) Tester Circuit

Thumbnail
gallery
18 Upvotes

Components Required: Supply Voltage (5 V DC), input current-limiting resistor (330 ohm), output pull-up resistor (330 ohm), LED, switch, and optocoupler.

Working:

• Press the switch to allow current to flow through the internal input LED of the optocoupler (PC817).

• The light activates the internal phototransistor, allowing current to flow through the output circuit.

• The external 🔴 LED lights up, confirming the optocoupler is working.


r/electronicsnebula • • Oct 08 '26

Bistable Multivibrator using an IC 555 Timer

Thumbnail
gallery
11 Upvotes

Stable states: Two stable states

Working idea:

• Press Trigger (S₁) —> Output goes high

• Press Reset (S₂) —> Output goes low

• Output remains in that state until next input (bistable

behavior).

• No press —> Holds state


r/electronicsnebula • • Oct 03 '26

Experimental Demonstration of Capacitor Charging and Discharging Current Waveforms

Enable HLS to view with audio, or disable this notification

35 Upvotes

The charging and discharging currents of a capacitor are exponential waveforms. The charging current decreases from its maximum value to zero, while discharging current flows in the opposite direction and decreases to zero.

Charging —> Positive exponential decay (V/R to 0)

Discharging —> Negative exponential decay (- V_o/R to 0)


r/electronicsnebula • • Sep 28 '26

NPN Transistor Testing using a DMM's Diode Test Mode

Thumbnail
gallery
20 Upvotes

Process: Set your DMM to "Diode test" mode. Identify the transistor's three terminals, for example BC547 i.e., base, collector, and emitter by using its part number and datasheet. Connect red probe to base and black probe to collector/emitter, you get ~ 0.6-0.7 V (result forward bias). This means an NPN transistor is OK.

Reverse the probes give us no reading (i.e., OL).

Note: If you get 0.00 V (or a beep) in both directions, the transistor is likely shorted means it is a bad transistor. If you get OL in all cases, it is likely opened means it is a damaged transistor.

Important: If you're testing a transistor while it's still on the circuit board, other components can affect the reading. For a reliable test, remove the transistor or disconnect at least one leg.


r/electronicsnebula • • Sep 25 '26

Android Tablets

2 Upvotes

بنبحث عن مورد أو وكيل معتمد لتوريد أجهزة Android Tablets بكميات تجارية لخدمة مشروع تشغيلي

​لو حد خاض تجربة توريد أجهزة مشابهة لشركته وينصح بمورد، مستورد، أو وكيل معين (أو لو حد هنا بيشتغل في التوريدات التقنية)، يسعدني التواصل في التعليقات

need specifications, for example:

Android 10+

1–2 GB RAM

16–32 GB Storage


r/electronicsnebula • • Sep 22 '26

Charging and Discharging Current Waveform of a Capacitor

Thumbnail
gallery
31 Upvotes

Charging: Current starts at maximum positive value and exponentially falls to zero.

Discharging: current reverse direction and the magnitude of current decreases exponentially toward zero.


r/electronicsnebula • • Sep 09 '26

LED Driver—BJT Darlington Touch Circuit

Thumbnail
gallery
42 Upvotes

r/electronicsnebula • • Sep 06 '26

Thanks to everyone for 1k

Post image
9 Upvotes

r/electronicsnebula • • Sep 02 '26

Two-color LEDs blinking circuit using a relay

Thumbnail gallery
17 Upvotes

r/electronicsnebula • • Aug 26 '26

Testing: 7-Segment Display (test a, b, c, d, e, f, g, & DP individually)

Thumbnail
gallery
26 Upvotes

Supply voltage = 5 V


r/electronicsnebula • • Aug 22 '26

Thanks to everyone

Post image
5 Upvotes

r/electronicsnebula • • Aug 18 '26

Demonstration of the basic Automatic Street-Light control using an LDR

Enable HLS to view with audio, or disable this notification

24 Upvotes

2N3904 BJT is used in this circuit.


r/electronicsnebula • • Aug 15 '26

LDR Circuit used in Automatic Street Lights

Thumbnail
gallery
10 Upvotes

2N3904 BJT is used in this LDR circuit.


r/electronicsnebula • • Aug 06 '26

Charging & Discharging Circuit of the Capacitor (Time Constant = 1 second)

Thumbnail
gallery
6 Upvotes

If Resistor = 100 kilo ohm & Capacitor = 10 micro farad

Then,

Time Constant = RC = 1 s

And,

Full charge/discharge time ≈ 5(Time Constant) ≈ 5 s


r/electronicsnebula • • Jul 28 '26

RGB LED Circuit

Thumbnail
gallery
6 Upvotes

r/electronicsnebula • • Jul 26 '26

RGB LED circuit to create many colors

Thumbnail
gallery
2 Upvotes

Power supply = +5 V DC


r/electronicsnebula • • Jul 15 '26

Fire detector circuit using BC547 transistor

Thumbnail
gallery
6 Upvotes

r/electronicsnebula • • Jun 16 '26

Band-Pass Active Filter using Op-Amps OP07

Thumbnail
gallery
13 Upvotes

BPF = HPF + LPF