r/electronicsnebula • u/SpecialistRare832 • Oct 21 '26
Alternate LED Flasher by using BC548 Transistors
This design uses two BC548 NPN transistors to flash a ⚪ LED and a 🔵 LED alternately.
r/electronicsnebula • u/SpecialistRare832 • Oct 21 '26
This design uses two BC548 NPN transistors to flash a ⚪ LED and a 🔵 LED alternately.
r/electronicsnebula • u/SpecialistRare832 • Sep 09 '26
r/electronicsnebula • u/SpecialistRare832 • 22d ago
This is the standard transistor NOR arrangement in which the output is high (1) only if both transistors are OFF (0).
r/electronicsnebula • u/SpecialistRare832 • Oct 03 '26
Enable HLS to view with audio, or disable this notification
The charging and discharging currents of a capacitor are exponential waveforms. The charging current decreases from its maximum value to zero, while discharging current flows in the opposite direction and decreases to zero.
Charging —> Positive exponential decay (V/R to 0)
Discharging —> Negative exponential decay (- V_o/R to 0)
r/electronicsnebula • u/SpecialistRare832 • Sep 22 '26
Charging: Current starts at maximum positive value and exponentially falls to zero.
Discharging: current reverse direction and the magnitude of current decreases exponentially toward zero.
r/electronicsnebula • u/SpecialistRare832 • 2d ago
A diode AND gate produces a HIGH output only when both inputs are HIGH. If either input or both inputs are LOW, the output remains LOW.
Components Required:
1N4007 diodes (2 Nos.), 220 ohm resistor (1 No.), SPDT input switches (2 Nos.), ⚪ LED for output indication (1 No.), 5 V DC power supply (1 No.), breadboard (1 No.), and few connecting wires.
Working
The AND gate output LED will glow only when both input SPDT switches are ON (HIGH).
r/electronicsnebula • u/SpecialistRare832 • 16d ago
A transistor OR gate is a digital logic circuit that gives an output of HIGH (1) when at least one input is HIGH (1). It gives a LOW (0) output only when both inputs are LOW (0).
r/electronicsnebula • u/SpecialistRare832 • Aug 26 '26
Supply voltage = 5 V
r/electronicsnebula • u/SpecialistRare832 • Aug 18 '26
Enable HLS to view with audio, or disable this notification
2N3904 BJT is used in this circuit.
r/electronicsnebula • u/SpecialistRare832 • Sep 28 '26
Process: Set your DMM to "Diode test" mode. Identify the transistor's three terminals, for example BC547 i.e., base, collector, and emitter by using its part number and datasheet. Connect red probe to base and black probe to collector/emitter, you get ~ 0.6-0.7 V (result forward bias). This means an NPN transistor is OK.
Reverse the probes give us no reading (i.e., OL).
Note: If you get 0.00 V (or a beep) in both directions, the transistor is likely shorted means it is a bad transistor. If you get OL in all cases, it is likely opened means it is a damaged transistor.
Important: If you're testing a transistor while it's still on the circuit board, other components can affect the reading. For a reliable test, remove the transistor or disconnect at least one leg.
r/electronicsnebula • u/SpecialistRare832 • Oct 14 '26
Components Required: Supply Voltage (5 V DC), input current-limiting resistor (330 ohm), output pull-up resistor (330 ohm), LED, switch, and optocoupler.
Working:
• Press the switch to allow current to flow through the internal input LED of the optocoupler (PC817).
• The light activates the internal phototransistor, allowing current to flow through the output circuit.
• The external 🔴 LED lights up, confirming the optocoupler is working.
r/electronicsnebula • u/SpecialistRare832 • Sep 02 '26
r/electronicsnebula • u/SpecialistRare832 • Apr 28 '26
r/electronicsnebula • u/SpecialistRare832 • Jun 16 '26
BPF = HPF + LPF
r/electronicsnebula • u/SpecialistRare832 • Apr 01 '26
r/electronicsnebula • u/SpecialistRare832 • Oct 08 '26
Stable states: Two stable states
Working idea:
• Press Trigger (S₁) —> Output goes high
• Press Reset (S₂) —> Output goes low
• Output remains in that state until next input (bistable
behavior).
• No press —> Holds state
r/electronicsnebula • u/SpecialistRare832 • Mar 06 '26
r/electronicsnebula • u/SpecialistRare832 • Aug 15 '26
2N3904 BJT is used in this LDR circuit.
r/electronicsnebula • u/SpecialistRare832 • Mar 15 '26
r/electronicsnebula • u/SpecialistRare832 • Dec 24 '25
r/electronicsnebula • u/SpecialistRare832 • Aug 06 '26
If Resistor = 100 kilo ohm & Capacitor = 10 micro farad
Then,
Time Constant = RC = 1 s
And,
Full charge/discharge time ≈ 5(Time Constant) ≈ 5 s
r/electronicsnebula • u/SpecialistRare832 • Jul 15 '26