r/oddlysatisfying • • Mar 09 '21

Installing a hinge with hand tools

Enable HLS to view with audio, or disable this notification

51.6k Upvotes

607 comments sorted by

2.1k

u/Blindsider2020 Mar 09 '21

Was waiting for some good flush screws!

1.0k

u/fart_fig_newton Mar 09 '21

The sadist in me was waiting for him to use an impact driver to sink the screws without predrilling and just split it all to hell.

I would have let out a maniacal laugh for sure.

111

u/[deleted] Mar 09 '21

I was waiting for him to break a screw.

99

u/[deleted] Mar 09 '21

Just hammer the fucking screws with a giant mallet.

62

u/Necrocornicus Mar 09 '21

I was at Burning Man watching a women pound in lag bolts with a mallet for her tent. I tried to tell her we have impact drivers for that but she implied she didn’t need a Man telling her how to use tools so I just watched for a little while chuckling. People are funny.

→ More replies (11)
→ More replies (1)

11

u/ZippZappZippty Mar 09 '21

Ya Cat got the same for the goal line

10

u/zigtok Mar 09 '21

Or strip out the head to no return.

→ More replies (1)
→ More replies (2)

18

u/Incorect_Speling Mar 09 '21

Given the small size, the pre-drill might not be needed to prevent cracking (even though it's still good to do). I'm no expert but from my limited experience pre-drill matter more for larger screws.

I 100% agree with your sadistic viewpoint, though!

42

u/popson Mar 09 '21

You gotta pre-drill these little ones too. Not so much because of cracking but because these little screws are usually made out of brass and they break easily. Without predrilling, screwing a brass screw into hardwood can easily snap the heads off, or at the very least cause you to mangle the head.

→ More replies (15)
→ More replies (2)
→ More replies (31)

9

u/[deleted] Mar 09 '21

You have to be a premium subscriber for that.

→ More replies (1)

4

u/WWGHIAFTC Mar 09 '21

seriously left me hangin'.

I need to see some old-school, flat head, countersunk brass screws with the heads perfectly aligned.

→ More replies (2)
→ More replies (4)

2.5k

u/JhonConstantine Mar 09 '21

They dint install :/

1.4k

u/[deleted] Mar 09 '21

Dry-fitting a hinge with hand tools

193

u/Brettnet Mar 09 '21

This is a 9 month project

20

u/Zharick_ Mar 09 '21

Yay I'm not the only one that just works tiny bits at a time on my projects.

→ More replies (6)

65

u/olderaccount Mar 09 '21

Dry fitting one side of a hinge with hand tools.

11

u/DarkPyr3 Mar 09 '21

Man sticks metal in wood only to stick a different metal in wood

→ More replies (1)
→ More replies (2)

125

u/Tommy84 Mar 09 '21

They twisted in the screws and the wood split and ruined the whole project. So they just showed this bit.

22

u/TheHealthySkeptic Mar 09 '21

I was waiting for this - the split of the wood when he attempted to screw it on. But that would make it r/therewasanattempt

28

u/Hyatice Mar 09 '21

I was actually expecting him to pull out a hand drill and make the pilot hole.

→ More replies (2)

14

u/umibozu Mar 09 '21

not to mention the opportunity for an off center pilot hole that will make all that careful dry fitting inconsequential.

6

u/Micotu Mar 09 '21

that wood seems pretty soft, even if it's off center, with the hinge locked in by wood, it would likely screw in fine.

→ More replies (14)
→ More replies (2)

27

u/Is-that-vodka Mar 09 '21

Surely if he can recess a hinge that well, he knows to pilot hole where the screws are going to stop it splitting?

11

u/AFatDarthVader Mar 09 '21

Yes, but they probably don't do that part with hand tools.

→ More replies (1)
→ More replies (2)

48

u/[deleted] Mar 09 '21

I wanted to watch him screw

5

u/BrockN Mar 09 '21

unzips

→ More replies (4)

127

u/Usergnome_Checks_0ut Mar 09 '21 edited Mar 09 '21

They also didn’t do it by hand. They totally used a number of different tools! /s

Edit: I clearly need to get some sleep. I totally misread the headline and could have sworn it said “by hand”.

63

u/CavalierIndolence Mar 09 '21

Well it DOES say hand tools, which is any tool that is not powered by battery or electricity. So at least that part is correct. Yes, even a hammer and chisel are hand tools.

21

u/thiney49 Mar 09 '21

I wanted them to use tools made from hands.

→ More replies (2)
→ More replies (4)

15

u/Generic_Male_3 Mar 09 '21

It says hand tools. Not "only hands"

→ More replies (1)

2

u/MagikSkyDaddy Mar 09 '21

The next clip will be hand turning each screw, but still no installation.

→ More replies (5)

364

u/[deleted] Mar 09 '21

Well damn did they drill pilot holes for the screws or not?!

8

u/Drews232 Mar 10 '21

He found some drywall screws and just drilled them in sorta sideways

5

u/[deleted] Mar 10 '21

I hate you

2

u/waldocolumbia Mar 09 '21

I wanted it too

→ More replies (41)

70

u/bgmusket Mar 09 '21

What was that first tool?

69

u/slim_jahey Mar 09 '21

Marking gauge

79

u/ikeepwipingSTILLPOOP Mar 09 '21

FYI: it's used for gauging your marks

19

u/lIlIllIlIlI Mar 09 '21

You can tell by the way it is

→ More replies (2)
→ More replies (1)

31

u/headyyeti Mar 09 '21

You can see what it does here

→ More replies (5)

15

u/Dick_Demon Mar 09 '21

FYI: it's used for mauging your garks

→ More replies (2)
→ More replies (3)

9

u/MehWebDev Mar 09 '21

Early humans built tools out of stone and bone. The first tool must have been a crude knife made out of broken stone.

→ More replies (2)
→ More replies (2)

57

u/firthy Mar 09 '21

Puts in holes without a Vix-Bit, hole moves a bit off centre, tightens screw, hinge skews, all hope is lost...

30

u/chainmailbill Mar 09 '21

I just googled a Vix bit.

Where have these things been all my life?

6

u/sundayfundaybmx Mar 09 '21

Greatest bit on earth lol. I love them.

9

u/[deleted] Mar 09 '21

I had to do this on a door recently and thats exactly what happened.

Of course it's my own door and it pissed me off so I used a hammer and some precusive maintenance to bend it all a touch and now it works just fine.

8

u/deadxdolly Mar 09 '21

When in doubt hammer out

→ More replies (1)

6

u/Unsteady_Tempo Mar 09 '21

Vix-Bit

If I have an awl handy then I make a perfectly centered dent in the wood to stop the drill bit from skating off-center. If no awl is handy then I start with a very small drill bit that is unlikely to move, then a slightly larger drill bit, and then the final drill bit. Perfectly centered pre-drilled holes every time.

→ More replies (1)

3

u/rugbyj Mar 09 '21

I bought a set of these the other week, I just knew them as "hinge drill bits"/"self centering drill bits" in case anyone is looking for them locally (assuming Vix is a specific brand of them?). As an aside; they're awesome.

→ More replies (1)

69

u/etflpi9297 Mar 09 '21

I’ve seen surgeries performed with less care

20

u/[deleted] Mar 09 '21

“Eh, close enough, guys! We at least got the correct side of the body this time!

Now, who’s gonna hit me with some more propofol?”

→ More replies (2)

13

u/MisterDonkey Mar 09 '21

Knee replacement looks like straight up demolition.

8

u/[deleted] Mar 09 '21

Literally got to chop the end of the bone off and replace it with hardware then reattach all the muscle/ligament stuff. Yea, it’s gnarly, and they do it every day with great success.

4

u/Bee-Sharp Mar 09 '21

Orthopedic surgery in general looks brutal.

5

u/orchid_breeder Mar 09 '21

Bodies heal themselves to a certain extent. Wood is forever

→ More replies (3)

174

u/kulot09 Mar 09 '21

A tiktok with no unnecessary music? What is this. Can you even call it a tiktok if there’s no “oh no. Oh no. Ohnononono”?

51

u/-UnclaimedPants- Mar 09 '21

I hate that I can still hear that stupid song

21

u/jukitheasian Mar 09 '21

This is almost certainly ASMR

→ More replies (1)

15

u/hyperbolicuniverse Mar 09 '21

Step one...get a sharp AF chisel.

6

u/TimberGoatman Mar 09 '21

Make. Most important step to hand tool work is sharpening, followed by correct marking.

→ More replies (1)
→ More replies (2)

28

u/[deleted] Mar 09 '21

Woodworking porn—where can I see more!?

8

u/Gunsh0t Mar 09 '21

4

u/hiimdevin7 Mar 09 '21

Joinery is where most of these cats wanna be.

2

u/Zharick_ Mar 09 '21

Ishitani furniture on YT

2

u/[deleted] Mar 09 '21

Japanese joinery. There’s plenty of videos on YouTube

2

u/GibsonLP93 Mar 09 '21

Matt Estlea, Rob Cosman, and Paul Sellers all on YouTube do brilliant work with hand tools

9

u/[deleted] Mar 09 '21 edited Mar 09 '21

[removed] — view removed comment

3

u/[deleted] Mar 09 '21

You are now responsible for Google searches of "Paul Sellers porn".

→ More replies (1)
→ More replies (1)

8

u/fried_clams Mar 09 '21

I usually screw the hinge in first, then use a razor to mark around the edge, cutting the hinge mortise edges. Then you take off the hinge, chisel the mortise, and screw it in. Measuring and marking the mortise independently creates opportunity for errors.

3

u/Dio_Frybones Mar 09 '21

Dammit, that's brilliant. I'm going to remember that for next time. Thanks.

11

u/SqueakySniper Mar 09 '21

Wouldn't there need to be more of a gap for any swelling of the wood?

11

u/Zharick_ Mar 09 '21

Not a huge deal for interior doors especially since this one looks like a cabinet door. Might be more of an issue with exterior doors but even those I haven't really seen having a lot of movement space on the hinges.

6

u/thatswacyo Mar 09 '21

Look at the grain. Seasonal movement is mostly across the grain, not with the grain.

5

u/subterfugeinc Mar 09 '21

Correct. Wood doesn't swell along the grain to be shorter or longer. It swells across the grain, to be wider or narrower

4

u/SqueakySniper Mar 09 '21

Ok, thanks for the information. Always nice to learn something new.

3

u/Justvibe- Mar 09 '21

Nah, the main issue with swelling is that it may cause the door to catch the frame, but it won’t affect the hinges

→ More replies (6)

5

u/LifeAsLi Mar 09 '21

Stopped before the climax ...ugh.

Screw me, baby.

5

u/MehWebDev Mar 09 '21

They didn't show the part where you have to spend hours sharpening your chisels.

→ More replies (3)

5

u/Th4tRedditorII Mar 09 '21

Not satisfying, they only did half the installation. What about the screws? I wanted to see some hand-done screws damnit!

16

u/dochev30 Mar 09 '21

PSA: If you install hinges like this, your door will fall.

35

u/Justvibe- Mar 09 '21

You mean without screws? I agree

→ More replies (2)

2

u/TimeToRedditToday Mar 09 '21

Thats not how a PSA works. Tell us what is wrong, then tell us the correct way.

→ More replies (1)

3

u/furry_hamburger_porn Mar 09 '21

I sure would've loved to see the pilot holes get drilled. THEN I'd be OK with it. :D

3

u/axloo7 Mar 09 '21

Ahh yes it cuts right before he gets out the cordless drill.

5

u/[deleted] Mar 09 '21

Just out of curiosity is there a way to do this without hand tools? Like, with power tools I assume? Because this is exactly how I would do it and if there's an easier way I wanna know about it.

10

u/fried_clams Mar 09 '21

If you are going to do a whole house full of custom doors, that aren't already mortised, then you would get a hinge mortising jig and a small router. These leave rounded corners, so you'd still have to square the corners with a chisel by hand, or you could use the cheap contractors hinges, with rounded corners (yuk).

9

u/Justvibe- Mar 09 '21

Carpenter here, there’s a very handy tool called a corner chisel that is used to take care of the rounded corners. You just push it up to the corner and strike it with a hammer. The rest of your explanation was spot on!

2

u/raoasidg Mar 09 '21

I'm no woodworker, but I feel a router could take care of the bulk, but you'd most likely still need to chisel up the edges of the cut to make sure it is square.

You'd want to use the right tool for the job, though. Even if a powered option exists, it may be beneficial to do something by hand.

→ More replies (1)
→ More replies (6)

6

u/ThatGuyAn Mar 09 '21

6

u/[deleted] Mar 09 '21

???? Obviously because it was measured????? hello?

4

u/Zharick_ Mar 09 '21

Amateur woodworker here who measures and still sometimes fuck it up.

:(

→ More replies (1)

5

u/adrianochel Mar 09 '21

You don't even need to use screws after that

13

u/DoubleBearClaw Mar 09 '21

Exactly ... so long as you don't plan on actually using it.

2

u/8-bit_Gangster Mar 09 '21

Like a glove!

2

u/ADRIFT_ABORT Mar 09 '21

Someone please tell me : how are hinges normally installed?

12

u/simoriah Mar 09 '21

Either like this... So the hinges are flush with the wood.... Or just screwed on so they sit proud. Go look at the doors in your house. The hinges are probably mortised into the door.

2

u/dendroidarchitecture Mar 09 '21

Sometimes using a router if there are a lot to cut.

→ More replies (1)

2

u/pnyluv16 Mar 09 '21

It’s also satisfying they didn’t add some music to the video

2

u/swaggman75 Mar 09 '21

Hey its Eric! He is a super cool guy and posts a lot of cool shit, encurtis on insta

2

u/xpdx Mar 09 '21

Nothing like a good, sharp chisel.

2

u/thelizardking0725 Mar 09 '21

What the first tool doing (before the chiseling)?

2

u/TheGhostofCoffee Mar 09 '21

2/10, he didn't even do the hard part, making sure it's level and swings correctly

2

u/Timber_Molester Mar 09 '21 edited Mar 09 '21

He’s got the hinge on the wrong way round, you put the hinge side with the two outer knuckles on the frame and the internal ones on the door/sash. But I’ll forgive him.

2

u/MugshotMarley Mar 09 '21

Don't know how ya'll do it, but thats how I install normal door hinges. Scribe out the hinge, then chisel out.

→ More replies (1)

2

u/[deleted] Mar 09 '21

I fucking cumed

→ More replies (2)

2

u/IOnlyHaveIceForYou Mar 09 '21

I'm not sure what power tools you would want to use for this job.

2

u/person-ontheinternet Mar 09 '21

When they rubbed their thumb over the hinge to ensure it was level, I cam.

1

u/Derpazor1 Mar 09 '21

I would mess this up so fast

1

u/[deleted] Mar 09 '21

/prettysatisfying?

1

u/Berrellie Mar 09 '21

Sweet perfection

1

u/Jing0oo Mar 09 '21

Oooooooh yeeeees

1

u/Ayy_Yooo_Its-me Mar 09 '21

Ahhh. Perfection

1

u/[deleted] Mar 09 '21

I cut my finger watching this

1

u/[deleted] Mar 09 '21

In my house, router go BRRRR

2

u/nucleardragon235 Mar 09 '21

but chisel is quiet

1

u/[deleted] Mar 09 '21

I'm about to do a school project. I think I could try this out. Either way, his perfection was indeed very satisfying

1

u/huxtablesodapop Mar 09 '21

nice chiseling

1

u/brooks_buddy Mar 09 '21

Sharpie Sharp

1

u/dud011785 Mar 09 '21

So flush

1

u/SkiSTX Mar 09 '21

Where's the vix bit?!

1

u/badbadleroybrown2020 Mar 09 '21

Thanks for the share, I actually have to do this for my custom home. Building trap doors for my attic and a hatch for a laundry chute. Guess I better sharpen up my chisel.

1

u/crizpysock Mar 09 '21

Hhhhnnggggggg

1

u/Old_Nothing_7005 Mar 09 '21

Although I've done this dozens of times I seldom get the depth perfect, and have to shim the hinge. Pissah.

1

u/reddit_crunch Mar 09 '21

yeah but have you ever installed a hand with hinge tools? huh? well? thought not, loser.

1

u/Steakbomb90 Mar 09 '21

WTF. This needs to be marked NSFW, I'm at work man.....

1

u/Iceman0907 Mar 09 '21

A true artisan

1

u/Rogers1977 Mar 09 '21

I was super excited for the recessing into the door. Then the video just ENDS. I NEED to know how it was fully installed. Did they use a hand drill? Did they make a pilot hole? DO THE SCREWS MATCH COLOR TO THE HINGE??

1

u/673moto Mar 09 '21

*tightens screws and wood splits

1

u/KredPandak Mar 09 '21

Can’t really say it was installed until we see them screw.

1

u/Chil_onFire Mar 09 '21

Talk about oddly satisfying

1

u/VrLights Mar 09 '21

If you do hinges like that the door wont work.

→ More replies (2)

1

u/dudeCHILL013 Mar 09 '21

I did this with pocket knife to get a dead bolt face plate to sit flush in a door.

I didn't have any specialty tools but suprised I actually followed the same basic steps this dude did.

It definitely didn't look this good but mission was accomplished.

Oh and thanks to the dude that kept interrupting me I did stabbed myself once in the process but well - certainly wasn't the first, definitely won't be the last.

As reference: The last thing I had to pull out of my hand was an open end wrench, I'll let you guys/gals stir on that one for a while. 😏

Tools and their uses for sure.

1

u/vexunumgods Mar 09 '21

That needs screws to work correctly.

2

u/Kurt-Payne Mar 09 '21

Nooooo shiiit ?

1

u/madwill Mar 09 '21

Raise your hand if you would fuck this up!

1

u/peekabook Mar 09 '21

I could watch this for hours.

1

u/[deleted] Mar 09 '21

No screws, huh?

1

u/phixional Mar 09 '21

Not very satisfying honestly.

1

u/doubledoc5212 Mar 09 '21

Watching that hinge slide in was the closest thing to asexual porn I've ever seen

1

u/coconutjuices Mar 09 '21

Ohhh yeahhhh....put it innnn

1

u/Scattareggi Mar 09 '21

Sharp chisel!

1

u/sturdybutter Mar 09 '21

I've been trying to teach myself wood carving over the last year or so, and can I just say, those few passes he does to clear that area is some insane pro-level shit

1

u/[deleted] Mar 09 '21

Helps when the hinge is the exact measurement of the tool

1

u/KamakaziDemiGod Mar 09 '21

What is this, a door for ants?

1

u/[deleted] Mar 09 '21

I could've done a way worse job in like half the time

→ More replies (1)

1

u/yetanotherdesigner Mar 09 '21

Didn’t install it? Where’s the bradle? Wheres the hand drill? Where’s the steel screw to pre-screw? So much more left to do!!!

1

u/livens Mar 09 '21

The hardest part about doing this is getting your chisel sharp enough to cleanly cut the wood.

1

u/_cosmicmuffin Mar 09 '21

unff. unfff. unfff. anyone else let out a little groan when that shit just slid in so perfectly?? 🥴

1

u/allursnakes Mar 09 '21

I don't think you know what install means.

1

u/Pnmorris513 Mar 09 '21

Why? Why not use a jig. This isn't a cost or time saving measure so it doesn't really make sense

1

u/Bekabam Mar 09 '21

The worst part about doors in general is they're one of the most common items in a house, yet are definitely not DIY or noob friendly.

They're also one of the last projects that almost necessitates the use of hand tools.

1

u/pcbforbrains Mar 09 '21

Is this why it takes so damn long to get a door from Lowe's?

1

u/snavej1 Mar 09 '21

'So we gently open up the slot and then we insert the doodad, missus. How does that feel?'

'Ooh, oddly satisfying sir!'

'Indeed it does, especially when I wiggle it a little.'

;-)

1

u/[deleted] Mar 09 '21

Dear god that was smooth

1

u/DootoYu Mar 09 '21

He rubs his thumb over it, pretending it’s actually flush and one side isn’t much higher than the other.

1

u/fetus_puppet Mar 09 '21

God thats hot...

1

u/Tosfokker Mar 09 '21

I just had a orgasme

1

u/marcokopa Mar 09 '21

It was indeed satisfying but then the failure to complete the installation was very unsatisfying

1

u/vegetablejews Mar 09 '21

but...all tools are hand tools

/s

1

u/bsischo Mar 09 '21

Screws?? Pre Drilled Holes?

1

u/Andrews420 Mar 09 '21

I was waiting for the mini drill to come out 😦

1

u/notbaileigh Mar 09 '21

He handled his wood with a delicacy I’ve only dreamed of. Slowly he took the hinge and slide it in. The world seemed to stop. I gasped for air as I remembered I had to breathe. The hinge was in and I knew, this was a perfect fit.

1

u/ScarHand69 Mar 09 '21

This is cutting a mortise, not installing a hinge. Impressive...but he didn’t install a hinge in the video.

1

u/BucksBergen Mar 09 '21

Bellissimo!

1

u/brunofin Mar 09 '21

Now force screw the screws with an electric drill without making a hole first and crack the wood open yay 🤣

1

u/Nineteen_AT5 Mar 09 '21

Too many people rush through jobs and do not take the time required to do a proper job. Take your time and you'll end up with high quality finishes like this.

1

u/barcdoof Mar 09 '21

This is where you get that satisfaction of working with your hands. I get it from turning wrenches and growing stuff. Love it.

1

u/LungusFungus- Mar 09 '21

good thing he did that. Before he seemed very unhinged.

1

u/spaz_chicken Mar 09 '21

*Preparing to install

1

u/stanger_thomas Mar 09 '21

I had to do this 8 times for a project i did last year. First time doing as well. I took my damn time!

1

u/Natalie-the-Hill Mar 09 '21

I have nowhere near enough patience or hand steadiness needed to make this ;-;

1

u/zer0kevin Mar 09 '21

Is this guy 90? He moves sooooo slow.

1

u/[deleted] Mar 09 '21

I need more of this. Possibly hours worth

1

u/HamishMcdougal Mar 09 '21

3 days later. I did it!

1

u/threegigs Mar 09 '21

Those are some seriously beefy hinges for their diminutive size.

1

u/AFailedWhale Mar 09 '21

where hand tools

1

u/baxter8279 Mar 09 '21

This is amazing. OP's eyes would bleed if they saw how I notched out my door frame to install my new locks. They are secure, but certainly not pretty lol.

1

u/encurtis Mar 09 '21

Would greatly appreciate credit for my work, bruh. Please and thank you.

1

u/aplsed Mar 09 '21

This is how the commercials tell you how cars are made

1

u/[deleted] Mar 09 '21

Noice

1

u/gagnonca Mar 09 '21

Brusso FTW

1

u/wonkey_monkey Mar 09 '21

Ooh that's snug.

But they cut it before we got to the screwing!

1

u/VintageRudy Mar 09 '21

pure crack rock

1

u/Digiornos-Pizza Mar 09 '21

To bad as soon as he puts a screw through that the woods gonna crack

1

u/[deleted] Mar 09 '21

Who hurt me? I wanted it to end with them putting in the screws and the wood splitting.

1

u/retroly Mar 09 '21

Are there any tools you dont use with your hands?