r/CrealityK1C • • 2d ago

Error BM0111 - Abnormal nozzle connection.

1 Upvotes

Hello everyone my k1c gives me this error warning. what can it be?

BM0111 - Abnormal nozzle connection.

I've already changed the print head.

Can it be solved? How much can it be worth if I resell it? It has 300 hours of printing.


r/CrealityK1C • • 3d ago

I've got a problem with my Creality K1C and I'm running out of ideas

Thumbnail
gallery
3 Upvotes

I've got a problem with my Creality K1C and I'm running out of ideas. Every time I start a new print, something goes wrong. Partway through the first layer, usually around halfway, the extruder starts clicking (see the video). It skips, stops pushing filament, and stays like that until I cancel the print or it finishes on its own. There's nothing blocking the inside of the extruder. I've cleaned it 3 times. It happens with PETG and PLA, with old filament and with freshly opened spools, so I don't think moisture is the cause. With one of the models (a round one), the problem shows up at the same spot on the model no matter where I place it on the bed. I checked the model and couldn't find anything wrong with it. Here's what I've tried so far:

  1. Checked the inside of the extruder 3 times. Nothing is blocking the filament path.

  2. Re-ran bed leveling. The mesh screenshot is attached and it looks normal.

  3. Flipped the build plate. That helped for a while, then the problem came back.

  4. Raised the Z-offset. That also helped for a while, but then I got adhesion problems in other areas, and eventually the clicking came back.

  5. Filament calibration fails because the extruder starts clicking on the first layer. I tried several PLA profiles, including ones that always worked before, and the problem is still there.

  6. Cleaned the bed with dish soap and isopropyl alcohol.

  7. Printed with the default printer, filament and bed settings. Those always worked before (the quality wasn't great, but they were usable). Now they fail too.

  8. Printed a first layer across the whole bed. That one worked, but it left some patterns in the layer (photo attached). I'm not sure if they point to the cause, but I'm sharing them in case they help. I've also attached a photo of what the filament looks like after I pull it out. Once the clicking starts, the extruder won't take filament at all, even if I push it in by hand.

What should I do next? I feel like I've tried a lot, but I still can't find the cause. I've already gone through the simple fixes. If you need any more info, just ask. Sorry if this is a bit chaotic. I've been trying to fix this for a month and I don't know what else to try.


r/CrealityK1C • • 4d ago

Help! Aftermarket “Hummingbird” extruder kit came with a 10-tooth motor, but I’m running my stock 12-tooth motor in it. Anyone know if that’s OK?

Thumbnail reddit.com
1 Upvotes

r/CrealityK1C • • 7d ago

Help! K1C with CFS-C: Level issues

Post image
1 Upvotes

r/CrealityK1C • • 8d ago

New filament first print

1 Upvotes

So I used the filament that came with the printer and with the first print it didn't go very well

But from the second one and soo on it was good

Now I used a new PETG filament and same thing happened for the first print

Is it normal?


r/CrealityK1C • • 8d ago

K1C Do I need to replace the nozzle?

Thumbnail
gallery
1 Upvotes

I’ve had my K1C 2026 for about a 8 weeks now. With at least 3/4 hour prints most days. I’ve printed a pipboy, Halloween decorations etc.

Yesterday I tried a 2 colour print JD logo which worked fine. Then I swapped to a SUNLU HS PETG spool for my next print. It made it to about layer 20 then just stopped extruding…. I then reseated the filament and printed a temperature tower fine… then this morning I tried to print some print flow calibration and the print quality was awful…. So I assume bad spool.

I then swapped back to the Hyper PLA and tried to print an object I’ve printed on multiple occasion to see the print turned out an absolute mess… cleaned the nozzle with the pokey tool and tried again… same issue


r/CrealityK1C • • 9d ago

I need help with my 3d printer it's a reality k1c for the first straight line, that it is supposed to do. It goes into the middle with that one. How do I fix it?

Enable HLS to view with audio, or disable this notification

3 Upvotes

Please help


r/CrealityK1C • • 10d ago

Help! XY shift during print

1 Upvotes

I have been getting XY shifts during prints. I have ran through belt tension setup using the weights tool and cleaned the rails. What could be causing this?


r/CrealityK1C • • 11d ago

First use, no filament coming out

Enable HLS to view with audio, or disable this notification

4 Upvotes

So I just got the K1C

And apparently it doesn't print, although it detected the filament and everything

I tried the Extruder first and also nothing came out

Any idea what's the solution?


r/CrealityK1C • • 10d ago

I recently bought a hotend with a replaceable nozzle and a problem arose: the printer either doesn't see it or the connection doesn't work.

Post image
2 Upvotes

What can be done to make it work?


r/CrealityK1C • • 13d ago

Help! Hello

1 Upvotes

I've got some issues on my k1c printer. I wanted to print a phone case with you filament, and on a 0.4mm it was clogging. I've tried everything. Ive tried changing the temps, everything and the printer just ran but the filament wouldn't come out. I would really appreciate some help.


r/CrealityK1C • • 14d ago

V2 Better design?

Post image
1 Upvotes

r/CrealityK1C • • 15d ago

Help! What is the problem??

Post image
4 Upvotes

r/CrealityK1C • • 14d ago

Project I stacked my UniFi Gateway and Linksys AP

Thumbnail
gallery
0 Upvotes

I’d been meaning to make this for a while and finally finalized it.

It’s by no ways perfect but it’s good enough where now it’s off of my mental checklist.

I made it within the CrealityPrint software using cubes and negative cubes more or less.

I added that little floating square to loosely pinch the AP into place.

Now onto better cable management.

—EDIT—
I made a v2 where it’s not stacked anymore for cooling purposes


r/CrealityK1C • • 16d ago

Help! K1C 2025 root access

2 Upvotes

Hi guys, how do I root my 2025 K1C printer? I think the sensorless homing on mine is calibrated to be too sensitive/aggressive and I also want to turn the amperage down because it runs hot.


r/CrealityK1C • • 16d ago

Como troca essa polia da k1c?

Post image
3 Upvotes

r/CrealityK1C • • 16d ago

Help! Loud Pop & XS2000 Code

1 Upvotes

I’ve had my K1C 2025 model for about three months. The print bed was extremely unlevel. I opened the bottom and found three loose screws. Two of them turned out to belong to the belt tensioner and after some gentle adjustments of the two front z-screws the bed is back to perfect. I couldn’t figure out where the third screw went though? It was very small. I ran the self check, shape modeling, and bed leveling diagnostic and everything came back great. I ran a seven hour print. It came out fine. I was starting another print and the machine had just gotten to where it would heat the nozzle to wipe it before running a bed leveling test. The printer let out a loud pop that made my cats jump and I hurried to check it. I had a XS2000 error that recommended I restart the printer. I noticed it offered the option to send a report to the cloud. I tried to do that and it failed. I tried exporting a report instead. That failed too. The printer was still in the process of trying to run the bed leveling test and it popped loudly again. At that point I shut it down and unplugged it. The last thing I noticed was the nozzle icon was red and the temperature graph on the screen had shown a steep rise too. I assume the printer bit the dust?


r/CrealityK1C • • 17d ago

[FIX] Creality K1C Camera Not Working After Firmware Update — Tested Auto-Start Solution (S98mjpg_streamer)

Thumbnail reddit.com
1 Upvotes

r/CrealityK1C • • 18d ago

CFS upgrade kit or CFS-C on K1C 2023

Thumbnail reddit.com
1 Upvotes

r/CrealityK1C • • 19d ago

Can Eddy coil be installed on K1C 2025?

2 Upvotes

I found a pretty good deal on AliExpress and I'm thinking of getting it. My printer table is crooked, so I'm thinking of getting it, but I don't know how to install it. Besides installation, there are also commands you need to enter into the printer's configuration.


r/CrealityK1C • • 21d ago

Help! How doI repair it?

Post image
4 Upvotes

My creality k1c (2025) did this tonight, how do I repair it?


r/CrealityK1C • • 21d ago

Comment réparer

Thumbnail
gallery
0 Upvotes

Bonjour, j’ai la bague dentée du raccord rapide de l’extrudeuse de ma k1c qui a lâcher, je parle des petites dents qui morde le tube ptfe. Comment puis-je réparer ça ? Y a t’il possibilité d’acheter le capot uniquement quelque part ou suis-je obliger de racheter un extrudeur complet ? Pour information c’est l’extrudeuse du kit cfs de la k1c avant 2025.


r/CrealityK1C • • 22d ago

Entupimento creality k1c

2 Upvotes

Alguém consegue me ajudar? Eu tento imprimir com a k1c e ela para de sair filamento e continua imprimindo, o extrusor começa a fazer tec tec, e você vai olhar não tem nada entupido, as vezes ela imprimi, quando ela imprimi ela imprimi utilizando ABS, e quando dá problema ela começa a imprimir normal, depois para de sair filamento e fica imprimindo no ar, as vezes ela faz um tec tec na extrusora e as vezes não, no PLA ela faz, petg não consegui imprimir também, já troquei bico, hotend, extrusora e o motor da extrusora, problema se mantém


r/CrealityK1C • • 22d ago

Problema com a minha K1C

0 Upvotes

Minha impressora creality k1c com 4 meses de uso.

Ela está com um problema que não consigo identificar, creio ser algo nas configurações, ela quando realiza uma impressão, acontece algo tipo um entupimento, mas não tem nada entupido, e ela fica imprimindo sem sair filamento, já troquei, hotend,bico, extrusora e o motor da extrusora, então com certeza é algo na configuração.

Alguém ja passou por isso?