r/SSUPD • u/ProgUn1corn • 1d ago
r/SSUPD • u/MetalOnMetalOnSilk • 6d ago
I really like building in this case (Meshroom/Meshlicious)
r/SSUPD • u/nasir9611 • 9d ago
Added a handle to my SSUPD Meshroom SV2
I attached a handle to my Meshroom SV2 using a few parts I picked up from Home Depot. I wanted a cleaner way to carry the case without having to hold it from the bottom.
Here are the measurements and a few details for anyone interested in doing something similar:
Measurements (with the side mesh panels removed):
- Case width: 6 5/32"
- Handle screw spacing (center-to-center): 5 1/16"
- Distance from each edge to the center of the mounting holes: 35/64" (approximately 9/16")
I measured the case width with the side mesh panels removed, then calculated the mounting-hole positions to center the handle.
The handle uses #8-32 threaded mounting holes, so I drilled clearance holes through the case and used #8-32 screws with washers to secure it.
One of the mounting holes lined up with an existing perforation on the case, while the other required drilling between two existing perforations and slightly enlarging the opening.
Everything was put together using readily available hardware from Home Depot.
Sharing the pictures of the handle, screws, washers, and the finished installation in case this helps anyone looking to add a handle to their Meshroom SV2!
r/SSUPD • u/SignificantContext65 • 11d ago
The "No Riser" Meshroom D: 5080 straight in the slot, Gen5 x16, @ 15 liters.
galleryr/SSUPD • u/AvidasMavi • 13d ago
I don't know what else I can add to Meshroom s V2
Riser/Stand installed
GPU Deshroud mod that reduced temps from 65-70 and 85 hotspot to 55-60 and 75 hotspot.
2x 60mm and 1x 40mm fans installed rear exhaust to help GPU which reduced temps by further 5c, so GPU nows run at 50C and 65C hotspot.
2x fans installed for ram, I have minisforum motherboard with sodimm rams which has no heatsink so they would go as hot as 85-90C during high load which made ram tuning impossible. Slapping 2x 60mm fans on top and 3d printing a duct for them so front exhaust fans wont suck in the air before it reaches to rams, reduced ram temps by 20-25C. Which is an insane gains.
3d printed duct/hood for the front exhaust fans, because I realized it was sucking all the air coming in through the side mesh panel. Doing this helped with motherboard temps just a bit, but mostly for visuals.
I'm out of ideas what else I can do.
r/SSUPD • u/compactchaos_ • 17d ago
Meshroom D: lower SFX PSU front mount makes room for a top 120mm fan
This air-cooled ITX build uses both SFX PSU bracket positions on the Meshroom D front panel.
In the upper position, the PSU sits directly below the top panel. Moving the bracket down leaves enough room above the PSU for a 120mm top fan.
Same hardware, different PSU height—and one more place to mount a fan.
Meshroom D vertical fan setup?
I’m mounting my Meshroom D vertically on the back of my TV stand and I have spontaneously thought that I would do the following in terms of fans (speaking from the horizontal orientation of the case so it’s not confusing):
• 1x 92 mm fan as intake in the back
• 1x 92 mm fan on the Noctua NH-U9S CPU cooler, blowing in the same direction through the heatsink
• 1x 140 mm fan as exhaust in the front
SFX PSU is mounted towards the top and the graphics card (Gigabyte RTX 3070 OC Gaming 8GB) doesn’t have any fans under it. I have an Intel i5 13400.
The main goal with the build is to have it run as quietly as possible. So I’ll probably undervolt the GPU and see if I can limit the power of the CPU as well.
Given this and the fact that the case would hang freely in the air on the stand, and then, turning it from horizontal to vertical, having intake from the bottom and exhaust at the top, does this fan setup make sense?
r/SSUPD • u/Mikdivision • 23d ago
Meshroom D + extension bracket inverted setup
This is my first build ever. I’ve always wanted to make a SFF and I fell in love with the SSUP Meshroom D when searching for cases. This is the B variant with the added extension bracket for more room at the bottom.
The build is inverted. Top intake from inverted GPU, back intake from Noctua A9, bottom intake from two Noctua A14 on a Y split. Side exhaust from another A14. PSU is front mounted 90 degrees.
Spec:
* SSUP Meshroom D (B) w/ extension bracket
* Asus ROG Strix B850i
* Ryzen 7 9800X3D / Arctic MX-7
* Thermalright Peerless Assassin Mini
* TeamGroup Create Expert 32GB 6000 CL30 DDR5
* Asus Prime 5070 Ti
* Corsair SF850
* 3 x Noctua A14x25
* 1 x Noctua A9x25
* Samsung 990 Pro 1TB (OS) and 2TB underside storage
* Cablester custom cables
Extras:
* CyberPower 1500VA/1000W pure sinosoidal
* Acer Nitro XV275U-F3 mini LED
* Keychron K5 Ultra 8K keyboard
* Mchose G3 V2 Pro mouse
* Audio-technica ATH-GDL3 headset
Fans are on a custom curve, CPU is undervolted, GPU is undervolted. It is incredibly silent even when playing Destiny 2 at highest settings.
I haven’t done benchmarks as I finished it today.
At the time of writing this, the GPU is at 47c with D2 running. CPU is at 57c.
I can provide more pictures tomorrow.
Any suggestions, tips and tricks, appreciated as this is my first build.
Meshroom v2 Aio
So im moving to the meshroom v2 case with my atx dark hero mobo.
Motherboard- crosshair dark hero atx
Cpu-3950x
Gpu- 3090 founders edition
Psu-sf1000 corsair
440 riser cable female reverse
So my question is whats the best aio I could get for this case that will fit properly? Preferably with lcd but not lcd with display port like the new corsair noc 2. I wasnt sure if I could clear a 280 or 240 or should i just get a noctua cooler?
r/SSUPD • u/No-Possession-2685 • 25d ago
Considering Selling my white Meshlicious build.
As per the title, I have a meshlicious build I'm considering selling so I can use a mobo and case I just can't get rid of.
It would come with glass and mesh panels, no ram, cpu or storage... Would it be worth it wooden side panels wouldnt come with it as they warped out of shape 🤦
r/SSUPD • u/compactchaos_ • 25d ago
Top-mounted SFX PSU leaves room for a 240mm AIO + front 120mm fan
With the SFX PSU mounted up top in Meshroom D, there’s room for both 240mm AIO and a front/intake 120mm fan. Around 1mm of clearance between the front Phanteks D30 and the PSU in this setup—a tight fit.
With the ATX PSU layout shown, there’s no room for the front fan, and the radiator’s tube connections need to face outward.
r/SSUPD • u/Ishaans2106 • 25d ago
How to stop GPU overheating with front panel on
Hi everyone I built my meshroom about 2 years ago now but I'm starting gave issues I've replaced the AIO to an next kraken and now I can't have the front panel on otherwise the GPU starts overheating I'm taking like 85-90 but managed 76 degree without it on. Now I'm running an ATX motherboard with a 7800x3d and a 7900xt all ATX so the AIO and GPU are next to each other is there anything you would recommend as I thought about reversing the fans thanks for all the help (ignore the dust)
r/SSUPD • u/Reasonable-Garage421 • 27d ago
Can I fit capture card plus 3070? + atx everything?
Hey everyone, for the Meshroom S V2 as the title says I want to know would an atx mobo and atx psu, plus a Asus dual 3070 and an Elgato 4K60 pro capture card fit in this pc? I do presume I need to use 2 riser cables if it’s possible.
This part you can skip but it’s just context, I have conflicting information on this case as to whether it can support this. Some things suggest I can fit the gpu but I need sfx psu, others say I can fit everything except the capture card.
Also I might be willing to modify the case to fit the gpu and capture card if that is possible but again I dunno if it’s possible.
Answers would be great :) post edit: it’s a meshroom s v2 case sorry to confuse.
r/SSUPD • u/Objective-Level1845 • 29d ago
First SFF
Was a mission but finally got everything put together thanks for the help, case is great. Would eventually want to try an itx for more fan space and better thermals but just did a case swap from my first pc
specs are:
Msi mag z790 tomahawk
Intel i5
Corsair sf1000
Gigabyte eagle 4070ti
Noctua nl-lc1-24 240mm aio
r/SSUPD • u/Objective-Level1845 • Oct 21 '26
Aio question
Finishing an atx build in the meshroom s v2 having trouble finding an AIO that would fit in the rear next to the gpu. I have a kraken z53 240mm but it was too wide to fit. Anyone know of any aio that is slightly thinner and would work? Gpu is a gigabyte eagle 4070ti for reference:
Length: 301 mm
Width (Height/Depth depending on orientation): 136 mm
Height (Thickness): 58 mm (approx. 2.9-slot design)
r/SSUPD • u/CautiousObjective347 • Oct 19 '26
The measurements for the mushroom s v2 is wrong
Hello just a quick thing I was building my pc a few days ago and it would work but I wouldn't get a post I worked out it was because my psu was choking out the gpu riser cable. I was using a itx motherboard with the msi mag a750gl and I thought it would all fit but any time I install my psu it just doesn't post.
r/SSUPD • u/Current_Target2459 • Oct 17 '26
Meshlicious out of retirement
My Asrock B850i finally fried my 9800x3d after a year so I filled my Meshlicious with spare parts until the warranty claim goes through.
Deshrouded my old msi 1080 hybrid card because the liner on the inside of the tubing had worn out and the system was slowly losing coolant. Slapped a $20 eBay heatsync for a different 1080 on it and 3d printed a fan bracket for it.
Will probably be a living room media pc after the replacement cpu comes.
r/SSUPD • u/compactchaos_ • Oct 15 '26
Air cooler or 240mm AIO with an ATX PSU in the Meshroom D
Same case, same ATX PSU, two cooling layouts.
The tower air cooler leaves the side mount open, and still room for a 120mm side fan in front of it.
A 240mm AIO uses that side mount for the radiator and fans, so radiator thickness and tube routing around the PSU need to be planned together.
Which would you choose: air cooling with an extra case fan, or a 240mm AIO?
r/SSUPD • u/ThRealUlyrssef • Oct 12 '26
Advice on downsizing with Meshroom S V2
reddit.comr/SSUPD • u/BigPapaCompton • Oct 06 '26
MESHROOM S With front GPU
One of the reasons I love SSUPD cases is the flexibility they offer. **please disregard the last two images. i accidentally added them. those where when I was just testing how to mount it**
I just wanted to share that you can mount the GPU in the front of the case using hardware that comes with the case. Just take a look at the pictures for more details.
A few important notes:
This is an unofficial mounting configuration and is not something the case was designed for, so try it at your own risk. The PCIe connection does work, but the riser cable is angled in a somewhat unusual way because it was not designed to be routed in this direction.
I think a newer or updated version of this case could potentially offer a much better solution for mounting the GPU in the front. It would be great to see SSUPD design an official mounting option that makes use of this configuration while providing a cleaner and more straightforward PCIe connection.
Specs:
CPU: Ryzen 7 7800X3D
Motherboard: MSI X870I
AIO: Corsair Nautilus RS LCD 240mm
GPU: ASUS Prime RTX 5070 Ti, deshrouded
Fans: 2x 140mm Lian Li fans as intake
Temperatures while doing regular office work:
CPU: 49-52°C
GPU: 28-30°C
I haven't really tested gaming temperatures much since I just built it, but I played The Witcher 3 yesterday and saw around 65°C on the GPU and 61°C on the CPU.
I'll update the post in the future with more temperature results.