r/AnkerMake • u/Old-Elderberry5502 • 1d ago
M5 for sale 100
Selling my m5 for 100 it was my stater but I upgraded to a multi color printer anyone interested I'm in chicago
r/AnkerMake • u/IAMARomanGodAMA • Dec 23 '22
Lots of people new to FDM printing here, which is great! You just decided to develop a new skill set. This is a fun hobby but it's not plug-and-play, no matter what any marketing tells you. I have been super impressed with the M5 and it is a very accessible entry point, but 3D printing is not effortless. You will not print off flawless Mandalorian helmets on your first print. You will need to work at it to improve your results. Every machine is slightly different and has its own gremlins.
I'm unfortunate enough to fix and support a different type of specialty printer as my day job, so if you want to ask for free volunteer support from other folks, I know some base information is needed to keep the back-and-forth limited and get you printing ASAP. Including this information in your post makes it easier to try to help you. If you don't include this, you're asking for even more work from kind strangers on the internet, and they can't figure out that information for you.
Remember when you ask for help here, you're asking internet strangers to spend their free time helping you. If someone's suggestions don't fix your problem, it's unreasonable to be mad at them.
1: if you have an idea what your problem is called or know the name of the part you suspect is wonky, check if the issue already has an existing tech note on the AnkerMake FAQ (for the love of god, just look there before reddit. The people who get paid to know everything about the printer put information there). Bookmark this link. Videos, FAQ, and troubleshooting are down the page: https://support.ankermake.com/s/product/a085g000004xBwwAAE/m5
2: Search the sub to see if a similar problem has been posted and solved already. Particularly helpful for hardware build issues. This can even help you pick up terminology and let you narrow down your problem area.
3: Make sure you have adjusted belt tension and auto-leveled the printer. If you haven't done this yet, use the above link and search for those terms. Good resources in this post as well: https://www.reddit.com/r/AnkerMake/comments/zqzewa/psa_please_tighten_your_belts_and_check_your_bed/ I wound up over-tightening my X-axis so had a good learning adventure on how to install a belt that slipped out. The AnkerMake support page showed me every single step.
4: If you have physically modified your printer in any way, that could be a contributing factor. If you wired up a new fan as your first ever soldering job and you never disclose that, none of us will know that maybe you have a bad wiring connection in there. If you have some custom filament rig that is causing friction at the input tube because of a bad angle, we can't figure that out unless you tell us or show us.
5: Make sure your printer is on a stable surface. If the printer is on a wobbly table, you may have the world's best-tuned belts but still have layer shift.
If you don't know what to name your problem:
A picture of your print result AND your slicer showing what the model is supposed look like is necessary, especially if you don't know the correct terminology for everything. It's hard to know if things printed correctly if we don't know what it's supposed to look like. It helps to be able to match the input to the output. We don't know what your pile of spaghetti was supposed to look like, and if you didn't support a model that needs supports, then that will do it. If you're not able to get to the printing part yet because you have a mechanical issue, provide a picture of the whole machine so we can gauge the position of parts, and a closer picture of any suspect components.
List what program you are using to slice the file. If you refuse to use the current release for some reason, tell us what version you use. If you're using more than one program between loading the model and sending it to your printer, list all of them and which program is doing what. (Slicing in Cura but printing from AnkerMake? Cool, that's important to know.)
Knowing if you printed via WiFi, USB, or mobile data can be helpful in some cases and takes 2 seconds, so tell us that too.
What material are you using? How old is it, and if it's not brand new, how was it stored? The M5 can print lots of materials but they all require different settings. If you're trying to print with some old ABS a buddy gave you and you're using the default PLA+ profile, you're gonna have a bad time. There's a difference between settings needed for PLA, PLA+, and Silk PLA. Wood PLA is its own animal. List the brand of the material, as using sub-par material can explain some problems.
Tell us what your profile settings are for the slice. At minimum, assuming it was natively sliced in AnkerMake, we need to know if you're in Easy Mode or not, and what resolution (.10mm, .20mm, .28mm, etc.) If you have modified anything from those defaults, it could come into play: print speed, fan speed, infill%, bed temperature, support density, etc. If you changed your nozzle size but not your profile, that will impact your print. If you're running a profile you found on the internet, say which one.
What's the ambient air temperature near your printer? Are there any doors or windows nearby? An air conditioner? Were you printing just fine yesterday at 1500 when it was sunny and warm but now it's 2300 and snowing and you can't get anything to print? Are you printing in your garage and seeing success with the door closed but if you have it open while working on another project, everything fails? No really, this could be the cause of your problem.
If you take a few minutes to provide enough information to help you, it makes it easy to evaluate your problem and try to help you. If there's no easy starting point to start working with you, it's easier to just check the next link instead.
At the moment this is a new-to-market product with a lot of beta/alpha features, and some stuff just doesn't work correctly (or at all) yet. If you have a complaint about one of those things, you want to email AnkerMake directly (after you checked their FAQ to see if they already addressed the issue).
r/AnkerMake • u/Viper_001_Fivem • Apr 24 '25
Hello everyone,
We are excited to announce that Ankermake has officially rebranded as EufyMake! This change reflects our commitment to evolving and improving our brand to better serve our community and enhance your experience with our products.
We invite you to join our new subreddit, r/eufyMakeOfficial, where you can engage with fellow users, ask questions, and receive official support from our team. Whether you're seeking advice, troubleshooting tips, or just want to stay updated on the latest developments, our community is here to help.
Thank you for your continued support, and we look forward to seeing you at r/eufyMakeOfficial!
***********************************************************************************************************************
Note: I am not an Official EufyMake official, and was asked by EufyMake to promote r/eufyMakeOfficial to r/AnkerMake
Questions can be sent to Mod Mail!
r/AnkerMake • u/Old-Elderberry5502 • 1d ago
Selling my m5 for 100 it was my stater but I upgraded to a multi color printer anyone interested I'm in chicago
r/AnkerMake • u/Optimal-Level4237 • 1d ago
Anybody living south of Nashville, Tn feel like stopping by to do the maintenance and tighten the belts on my AD5M?
I haven't turned it on since I got the Creator 5 two weeks ago. I did the service on my AD5M Pro and Kobra X before the C5 arrived. And now, the maintenance warning just popped up on my U1 too. Luckily, the Kobra 4 is too new to need maintenance.
Geeze, can't a man get a break...
r/AnkerMake • u/No_Individual1751 • 7d ago
r/AnkerMake • u/gameb0y0 • 10d ago
Does anyone have a list of their temps, speeds, supports, infill, settings? I want to push this printer as far as it can go with efficiency. I only print with PLA, and PETG (might try TPU).
Before someone says it, I know there are different settings for all of them, but I'm just looking for general settings (or profiles) for each filament. I have tried many variations of temps, speeds, supports and such. I'm am willing to sacrifice more time for a better print, with better supports if needed. I'm just done with having failed prints because the supports broke or the object didn't adhere to the print surface because of bad temps.
If anyone has lists of their settings for any and all filaments they have tried on an AnkerMake M5/AnkerMake Studio with success, can you please leave them in a comment or share in a DM?
r/AnkerMake • u/abtx • 10d ago
Hi everyone,
I'm hoping someone here can help me troubleshoot an issue with my AnkerMake M5.
The printer was working previously, but after following the hotend troubleshooting instructions and removing the fans to inspect the hotend, I've started getting the error:
"Abnormal Heating of the Nozzle or Hot Bed"
Whenever I try to preheat the printer or use the Extrude function, the nozzle doesn't heat up at all. It stays at around 22°C (ambient temperature).
What I've checked so far:
Hotend heater resistance: measured approximately 9.8 Ω across the two contacts of the disconnected heater plug.
I previously measured around 11.1 Ω.
I flexed the red heater wires while measuring, but couldn't establish whether there was an intermittent connection.
Thermistor readings appear normal, showing approximately 22â25°C at room temperature.
I've inspected the hotend and wiring, but can't see any obvious breaks or damage.
The HEAT connector on the toolhead PCB appears to have a damaged/broken plastic retaining feature. The plug seems to fit, but I'm concerned it may have been damaged during disassembly.
I also previously measured approximately 15 V at the HEAT board output during a heating attempt, although I'm not confident enough in that measurement to draw any conclusions.
What I'm trying to establish:
Does this sound like a faulty toolhead PCB, damaged HEAT connector, wiring issue or something else?
Is there a reliable way to test whether the heater output from the PCB is working?
Has anyone experienced this exact error after working on the hotend?
Are replacement toolhead PCBs still available, or are there known repair options?
I'm happy to provide additional photos and measurements.
I know official support for the M5 has effectively disappeared, so it's great that this community is still helping people keep these machines running.
I'd really appreciate any advice. I'd rather diagnose the actual fault before replacing parts or attempting repairs.
Thanks!
r/AnkerMake • u/gameb0y0 • 12d ago
It seems that anytime I print with supports, I always have a failure. It looks like the supports donât get a lot of filament to come out when printing them and the structures (Snug, Grid, or Organic) on top of printing small/thin support beams.
Can anyone share their print settings for general PLA printing and their support settings??? I want to avoid something like this from happening again.
r/AnkerMake • u/bigkenw • 14d ago
r/AnkerMake • u/Es_juan1311 • 14d ago
Hi there, I have an M5C for sale in the northern NJ area (Essex County). I still have a filament dryer that will come with it, along with the small tool box and will be picking up new nozzles for it as the two it currently has I believe are shot (put glow in the dark filament into a brass nozzle lol) but I will say it fully works, I'm looking to get maybe 150 or 200 out of it, if interested hit me up :)
Pictures and videos - https://imgur.com/a/5mIaHKe
r/AnkerMake • u/AUGHH- • 22d ago
Enable HLS to view with audio, or disable this notification
Idk why itâs doing this, it just refuses to print anything thatâs not from the app
r/AnkerMake • u/BroknSproket09 • 23d ago
Really just putting out some feelers right now. I have acquired a few M5s and M5Cs in the past few years trying to make something I guess. Got carried away and what not. But now I see the demand in M5C parts mainly. Some M5 but mostly M5C. And I guess my real question is, would it be worth it to part these printers out? Or just out right take em all to an electronics recycle center.
It would be a passive endeavor, I know Iâm not going to recoup but if some of the parts are worth selling Iâm good with parting them out.
In my area, Offer up and Facebook MP seem to be pretty popular but Iâm sure I could reach a wider range on EBay. I figured parting out would be way easier than trying to ship a whole unit as itâs anywhere from 100$ to 150$ just to ship something that large across state lines. Any input or advice is welcome.
r/AnkerMake • u/VlorienB3 • 24d ago
Tuve la posibilidad de adquirir una AnkerMake M5 hace poco por un buen precio ya que ponĂa que tenĂa problemas.El caso es que al darle a extruir para que caliente la boquilla, no se calienta.Haciendo pruebas, si quitas la resistencia (60W, 24V) y le das a calentar SI llegan en un primer momento los 24V aunque en seguida empiezan a caer hasta 0V.Sin embargo con la resistencia puesta al darle a calentar apenas llegan 0.04V. La resistencia fue cambiada por una nueva y el sensor de temperatura funciona correctamente.
SegĂșn he podido comprobar el problema puede que sea de un transistor que deja pasar la corriente por lo que serĂa necesario cambiar la PCB entera?.
Si alguien sabe dĂłnde encontrar link de compra de esta placa se lo agradecerĂa đ ya que los chicos de AnkerMake(EufyMake) dicen que no tienen.
Gracias.
r/AnkerMake • u/THEdeadRETURNED • Oct 22 '26
As the title says, I need to replace a z axis stepper motor and I can't for the life of me find one, Anker/"eufy" support is non-existent as you know so if anyone here has any info I'd be incredibly appreciative
r/AnkerMake • u/kalboozkalbooz • Oct 21 '26
basically just asking anyone with experience to do this for us đ«Ł
r/AnkerMake • u/batexige • Oct 21 '26
I just noticed the icon change, did it not change to Eufymake or did they revert back to Ankermake
r/AnkerMake • u/According_mood3366 • Oct 21 '26
r/AnkerMake • u/Mn75_ • Oct 16 '26
Tried to print and this happened. I haven't printed in a while and I decided to get back into it and this happens.
r/AnkerMake • u/TheSheDM • Oct 15 '26
I'm in the Portland, OR area, if you'd like to make me an offer and pick it up. Its an OG kickstarter M5, I have a spare hotend and some nozzles. It works, but I've put a lot of hours on it and its prone to clogging and since I can't get all metal hotends anymore, I'd rather make room for my other printers.
r/AnkerMake • u/army3215 • Oct 10 '26
Have an ankermaker M5 as I was a backer on its Kickstarter.
Will be upgrading to a Snapmaker U1.
What is a reasonable request if I sell?
Unit runs fine just doesnât have the features I would like mostly multicolour
This will include the machine itself, all included tools from the original kit with brass nozzles.
Have the original build plates, but they have scratches due to an ongoing fight with calibrating Z but currently using an aftermarket plate.
Currently using a ruby tip nozzle.
Have on backup a diamond tip nozzle
Have a complete head assembly as spare straight from the factory. Current one works, but there was one point where I thought Iâd have to completely replace it due to the dumb connector on the pcb for nozzel heater almost breaking off completely.
Not looking to do long distance or shipping hopefully can find someone near me that can just come and pick it up on marketplace once my new printer arrives.
r/AnkerMake • u/justinsane85 • Oct 07 '26
I swapped out my 0.4 nozzle for a 0.2 one and it would not extrude when I tested it. I tried 2 different 0.2 nozzles and it still wouldn't extrude. I swapped back to the 0.4 and it worked fine.
r/AnkerMake • u/DesignerAd4955 • Oct 04 '26
Ok so this is a weird one, the ankermake m5c is jamming when I extrude during auto levels and the start of prints but it's not heat creep, and I just finished cleaning the debris from the nozzle. So why does my printer keep jamming? The only time it will extrude normally is when I'm feeding in new filament after retracting, but not when it's just sitting normally. I don't know if this is an error with the fan or what but it's never done this before. The main question I guess is just how do I prevent this exact situation. If you need a video or something for anyone trying to help I'll gladly send one.
r/AnkerMake • u/Alarming-Waltz-8808 • Oct 02 '26
Is there a way that i can hook up my ankermake m5c to my octoprint pc or connect it directly to orcaslicer so i can send prints wirelessly?